Filament config?
-
@briskspirit I disabled Temperature Control from the addon "printer settings" in the cura "marketplace".
-
I have dipped a toe in by setting baby stepping -0.2 for PLA since it likes more squish than PETG. M290 R0 S-0.2 Is this the wrong approach? I could set the offset in the slicer I suppose. genghisnico13, you are a mad man
edit: So much for that idea. It doesn't survive a power cycle.
-
@3dmntbighker If you have a custom config.g setup for the filament you can load it at startup so it should be applied again after a power cycle.
Baby stepping is different than the live Z adjust in Marlin, etc. It's not a permanent change.
-
@phaedrux said in Filament config?:
@3dmntbighker If you have a custom config.g setup for the filament you can load it at startup so it should be applied again after a power cycle.
Baby stepping is different than the live Z adjust in Marlin, etc. It's not a permanent change.
I added it to my PLA profile in S3D. It works fine there. I'm sure there are multiple ways to accomplish a Z offset like that. It's nice to have a flat stable bed that a 0.05 offset is actually useful for. I think I got super lucky with my Ender 3. I have not even bothered to change the wimpy bed springs. My first layers are pr0n-O-graphic
-
@3dmntbighker I think you may be missing M703 to execute the filament specific config.g file.
https://duet3d.dozuki.com/Wiki/Gcode#Section_M703_Configure_filament
-
@phaedrux said in Filament config?:
@3dmntbighker I think you may be missing M703 to execute the filament specific config.g file.
https://duet3d.dozuki.com/Wiki/Gcode#Section_M703_Configure_filament
Hmm, I added M703 to to tpost0.g and config.g still only runs at the time you load the filament. The filament name loaded survives a power cycle, but PLA/config.g is not run again after a power cycle? Or do you need the M703 in both tpost0.g and sys/config.g? If I deselect tool0 and select it again it looks like M703 doesn't run either. I have to unload and reload the filament.
-
@3dmntbighker I could see needing to add it to config.g, but it doesn't sound like it's working as intended. I think @chrishamm developed this functionality?
-
I added M703 in start.g.so at the beginning of a print all filaments specifics are loaded
-
@alexlin said in Filament config?:
I added M703 in start.g.so at the beginning of a print all filaments specifics are loaded
I have a stop.g but no start.g?
-
@3dmntbighker you can create it. It will be run first at the start of every print before the slicer start gcode.
I use it to do a preheat and home the printer, reset any extrusion or speed factors, reset baby stepping, and play a little tune.
-
@phaedrux said in Filament config?:
@3dmntbighker you can create it. It will be run first at the start of every print before the slicer start gcode.
I use it to do a preheat and home the printer, reset any extrusion or speed factors, reset baby stepping, and play a little tune.
S3D does a lot of that for you in the start code. But putting it in Duet code and purging your slicer means you don't have to worry what slicer you are using I suppose.
I was thinking yesterday that we need a pinned thread of people's musical code
-
@3dmntbighker Agreed! Here's mine: https://www.dropbox.com/sh/24m8me9jieqk725/AACJMSA0qlxw3KPLf_cjIVT5a?dl=0
