Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    E3d V6 and KEENOVO Silicone Heater

    Scheduled Pinned Locked Moved
    Tuning and tweaking
    2
    8
    987
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Karimundefined
      Karim
      last edited by Karim

      Hey Guys trying to tune my E3d V6 and KEENOVO Silicone Heater 400x400mm 1000W 110v. The hotend and Bed heat up.

      ; Heaters
      ;Bed
      M307 H0 B0 S1.00 ; Disable bang-bang mode for the bed heater and set PWM limit
      M305 P0 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 0
      M143 H0 S120 ; Set temperature limit for heater 0 to 120C
      M305 P1 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 1
      ;E3dv6
      M143 H1 S280 ; Set temperature limit for heater 1 to 280C
      M305 P2 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 2
      M143 H2 S280 ; Set temperature limit for heater 2 to 280C

      M307 H0
      Heater 0 model: gain 204.4, time constant 836.7, dead time 1.5, max PWM 1.00, calibration voltage 24.3, mode PID, inverted no, frequency default
      Computed PID parameters for setpoint change: P482.3, I13.547, D511.5
      Computed PID parameters for load change: P

      Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 229C.
      Auto tune heater 0 completed in 1316 sec
      Use M307 H0 to see the result, or M500 to save the result in config-override.g

      Auto tune phase 3, peak temperature was 120.8
      Auto tune phase 2, heater off
      Auto tune phase 1, heater on
      M303 H0 S120

      M307 H1
      Heater 1 model: gain 800.1, time constant 205.0, dead time 5.2, max PWM 1.00, calibration voltage 24.3, mode PID, inverted no, frequency default
      Computed PID parameters for setpoint change: P8.8, I0.268, D32.0
      Computed PID parameters for load change: P8.8,
      PMM500
      Warning: No M501 command was executed in config.g
      PMWarning: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 825C.
      Auto tune heater 1 completed in 272 sec
      Use M307 H1 to see the result, or M500 to save the result in config-override.g
      PMAuto tune phase 3, peak temperature was 252.8
      PMAuto tune phase 2, heater off
      PMAuto tune phase 1, heater on
      PMM303 H1 S240
      Auto tuning heater 1 using target temperature 240.0°C and PWM 1.00 - do not leave printer unattended

      M307 H2
      Heater 2 model: gain 731.8, time constant 198.3, dead time 4.2, max PWM 1.00, calibration voltage 24.3, mode PID, inverted no, frequency default
      Computed PID parameters for setpoint change: P11.4, I0.393, D33.9
      Computed PID parameters for load change: P11.
      PMM500
      Warning: No M501 command was executed in config.g
      PMWarning: Heater 2 appears to be over-powered. If left on at full power, its temperature is predicted to reach 756C.
      Auto tune heater 2 completed in 271 sec
      Use M307 H2 to see the result, or M500 to save the result in config-override.g
      PMAuto tune phase 3, peak temperature was 249.7
      PMAuto tune phase 2, heater off
      PMAuto tune phase 1, heater on
      PMM303 H2 S240
      Auto tuning heater 2 using target temperature 240.0°C and PWM 1.00 - do not leave printer unattended

      1 Reply Last reply Reply Quote 0
      • Phaedruxundefined
        Phaedrux Moderator
        last edited by

        What is the issue? It looks like it worked.

        If you used M500 to save the results to config-override.g you'll need to add M501 to the end of your config.g to load them at startup.

        Alternatively, you can copy and paste the lines from config-override for H0 and H1 into config.g to make them permanent.

        Z-Bot CoreXY Build | Thingiverse Profile

        1 Reply Last reply Reply Quote 0
        • Karimundefined
          Karim
          last edited by Karim

          ; config-override.g file generated in response to M500 at 2019-01-02 15:07
          ; This is a system-generated file - do not edit
          ; Heater model parameters
          M307 H0 A204.4 C836.7 D1.5 S1.00 V24.3 B0
          M307 H1 A800.1 C205.0 D5.2 S1.00 V24.3 B0
          M307 H2 A731.8 C198.3 D4.2 S1.00 V24.3 B0
          M307 H3 A340.0 C140.0 D5.5 S1.00 V0.0 B0
          M307 H4 A340.0 C140.0 D5.5 S1.00 V0.0 B0
          M307 H5 A340.0 C140.0 D5.5 S1.00 V0.0 B0
          M307 H6 A340.0 C140.0 D5.5 S1.00 V0.0 B0
          M307 H7 A340.0 C140.0 D5.5 S1.00 V0.0 B0
          G10 L2 P1 X0.00 Y0.00 Z0.00 U0.00
          G10 L2 P2 X0.00 Y0.00 Z0.00 U0.00
          G10 L2 P3 X0.00 Y0.00 Z0.00 U0.00
          G10 L2 P4 X0.00 Y0.00 Z0.00 U0.00
          G10 L2 P5 X0.00 Y0.00 Z0.00 U0.00
          G10 L2 P6 X0.00 Y0.00 Z0.00 U0.00
          G10 L2 P7 X0.00 Y0.00 Z0.00 U0.00
          G10 L2 P8 X0.00 Y0.00 Z0.00 U0.00
          G10 L2 P9 0.00 Y0.00 Z0.00 U0.00

          Phaedruxundefined 1 Reply Last reply Reply Quote 0
          • Phaedruxundefined
            Phaedrux Moderator @Karim
            last edited by

            @karim said in E3d V6 and KEENOVO Silicone Heater:

            M307 H0 A204.4 C836.7 D1.5 S1.00 V24.3 B0
            M307 H1 A800.1 C205.0 D5.2 S1.00 V24.3 B0
            M307 H2 A731.8 C198.3 D4.2 S1.00 V24.3 B0

            Copy and paste those into config.g for your 3 heaters. Maybe add a comment about what temp you tuned to.

            Z-Bot CoreXY Build | Thingiverse Profile

            1 Reply Last reply Reply Quote 0
            • Karimundefined
              Karim
              last edited by

              This is what it should look like.
              ; Heaters
              ;Bed
              M143 H0 S120 ; Disable bang-bang mode for the bed heater and set PWM limit
              M305 P0 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 0
              M307 H0 A204.4 C836.7 D1.5 S1.00 V24.3 B0 ; Set temperature limit for heater 0 to 120C

              ;E3dv6
              M143 H1 S280 ; Set temperature limit for heater 1 to 280C
              M305 P2 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 1
              M307 H1 A800.1 C205.0 D5.2 S1.00 V24.3 B0
              M143 H2 ; Set temperature limit for heater 2 to 280C
              M305 P2 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 2
              M307 H2 A731.8 C198.3 D4.2 S1.00 V24.3 B0

              Phaedruxundefined 1 Reply Last reply Reply Quote 0
              • Phaedruxundefined
                Phaedrux Moderator @Karim
                last edited by

                @karim said in E3d V6 and KEENOVO Silicone Heater:

                M143 H2 ; Set temperature limit for heater 2 to 280C

                You've missed the temp limit for heater 2.

                Otherwise I think that looks ok.

                Z-Bot CoreXY Build | Thingiverse Profile

                1 Reply Last reply Reply Quote 0
                • Karimundefined
                  Karim
                  last edited by

                  @karim said in E3d V6 and KEENOVO Silicone Heater:

                  M305 P2 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 1

                  Yea it ok now, I am testing it.

                  M305 P1 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 1

                  This one had to fix too, change from P2 to P1.

                  1 Reply Last reply Reply Quote 0
                  • Karimundefined
                    Karim
                    last edited by

                    Thank you, Everything seem ok.

                    1 Reply Last reply Reply Quote 1
                    • First post
                      Last post
                    Unless otherwise noted, all forum content is licensed under CC-BY-SA