DuetWiFiFirmware minor release 1.15c
-
Forgive me for being cureas, but how is this going to fix my issue with the motors being drive on when they are not supposed to be. I mean this gcode is that same as i used on the Old Duet. So should it not print the same or maybe beater? I can see issues with the Controller not doing well with bad configuration, but that is fixed right?
So fixing the Config.g is a Good place to start. but non of the changes i have made, has solved this issue. Do you guys want me to run a File with a Specific gcode in it? For Debugging?
I mean i can configure it into thinking its got a Mixing hotend, but I don't have a mixing hotend to test it with.
-
Should i be configuring the Step mode on the Stepper motor drivers? if so what would be the equivalent to the default mode in the Duet?
-
Sorry old Duet, Example: M909 X3 Y5 Z2 E3
-
Sorry, but I'm just trying to help. I just don't understand how your printer is configured. You said
Quote….......
Extrudes: 2
Hot ends: 1I indeed fead different Filaments into one hotend (2 feeds).
...........end of quote.From that I assumed that it was a mixing hot end. Now you say that it's not. So I'm not sure what you mean. Do you have two extruders but only use them one at a time?
In your config.g you have tools defined to use 5 extruders, 3 of which which don't exist and you have a T4 command which selects one of these tools. I have no idea how the firmware would react to that but it is clearly something that needs correcting.
-
ReRap firmware doesn't use M909. Use M350 instead. I believe the default is 16x microstepping with interpolation.
-
Correct, i use one extruder at a time. I have a Jig that feeds the filament from 4 extruders into one mounted in the middle of my boden tub
-
Now you are saying that you have 4 (or 5 ) extruders when previously you said 2. I have no idea how you can be driving them all when the Duet WiFi on it's own only supports 2 extruders. Sorry but I'm going to have to give up with this.
-
Guy, how is the jig operated? Do you have 4 seperate extruder motors and 1 hotend or 1 extruder motor and the input is somehow switched?
-
4 separate extruder motors and 1 hotend. Its just a train track for the boden tubes. the jig is not connected to any electronics. just maniacal. no moving parts. Any one can print it
-
4 separate extruder motors and 1 hotend. Its just a train track for the boden tubes. the jig is not connected to any electronics. just maniacal. no moving parts. Any one can print it
OK, but the Duet WiFi only has 2 extruder drive outputs, so how are you driving the other 2 extruder motors?
-
not right now, wating for the new expansive board
-
Sorry Expansion board
-
Got [dc42/RepRapFirmware] M572 Loosing steps in XY email, was able to reproduce on my printer, but it made my over extrusion on line changes worse. Hop info helps
-
OK, i put new E firmware in. and Still had the same problem. So i put this into the Config.g file:
M572 D0 S0.00 ; Set extruder 0 pressure advance
M572 D1 S0.00 ; Set extruder 1 pressure advanceproblem is not as bad. in fact just a little bit of Extrusion error now when the program moves to the beginning of the next line
-
Ok, got it to work, this is what i ended up with for a Configuration:
; Configuration file for RepRap Ormerod
; RepRapPro Ltd
;
M111 S0 ; Debug on
M550 PTricolour Mendel WIFI
M551 Pgdww1620
M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0xEA ; Set the MAC address
M552 S1 ; Enable WiFiM555 P2 ; Set output to look like Marlin
M575 P1 B57600 S1 ; Comms parameters for PanelDue
M906 X800 Y1000 Z800 E800:800 ; Motor currents (mA)M305 P0 R4700 T10000 B3988 ; set bed thermistor parameters
M307 H0 A117.7 C395.8 D1.8 B0
M307 H1 A759.1 C95.9 D5.8 B0M574 X0 S1 ; Set endstop configuration
M574 Y2 S0 ; Set endstop configuration
M574 Z0 S1 ; Set endstop configurationM569 P0 S0 ; Set X Axis Direction
M569 P1 S1 ; Set Y Axis Direction
M569 P2 S0 ; Set Z Axis Direction
M569 P3 S0 ; Set E0 Axis Direction
M569 P4 S0 ; Set E1 Axis DirectionM558 P1 X1 Y0 Z1 ; Set Z probe type
M92 X100.25 Y100.25 Z4001.50 E420.00:420.00 ; Set axis steps per unit
M570 S180 ; Set heater timeout
M667 S0 ; set Cartesian modeM350 X16 Y16 Z16 E16:16 I01 ; Set microstepping mode
M563 P0 D0 H1 ; Create tool 0 = Color 1
M563 P1 D1 H1 ; Create tool 1 = Color 2
M563 P2 D2 H1 ; Create tool 2 = Color 3G10 P0 X20.0 Y0.0 Z0.0 S0 R0 ; Set tool 0 operating and standby temperatures
G10 P1 X20.0 Y0.0 Z0.0 S0 R0 ; Set tool 1 operating and standby temperatures
G10 P2 X20.0 Y0.0 Z0.0 S0 R0 ; Set tool 2 operating and standby temperaturesM106 P2 T45 H1 ; Fan control, Thermostatic on Heater H1
M572 D0 S0.00 ; Set extruder 0 pressure advance
M572 D1 S0.00 ; Set extruder 1 pressure advance;M566 X600 Y600 Z5 E10 ; Set allowable instantaneous speed change
M201 X800 Y800 Z15 E1000:1000 ; acceleration tweaks for improved finish
M203 X15000 Y15000 Z150 E3600:3600 ; speed tweaks for improved finish
;
M208 X200 Y200 Z120 ; set axis max travel
M208 X0.0 Y0.0 Z0.0 S1 ; set axis minimum (adjust to make X=0 the edge of the bed)G21 ; Work in millimetres
G90 ; Send absolute coordinates…
M83 ; relative extruder movesG31 P500 Z1.30 ; Set the probe height and threshold PLA = 0.65, ABS = 0.75
T2
M500 ;Store setting in EEPROM -
Are you certain that setting nonzero extruder pressure advance in M572 is causing a problem? Also, have you checked on the web interface or by sending M115 that you really are running firmware version 1.15e? Firmware updates do fail sometimes.
-
No Actually, it just helped. Things started working right when i put the M667 S0 and the M500. I can set the M572 D0 S0.00 to something other then zero. Whats a Recommended value to start with?
-
oww, yes i am running firmware version 1.15e. At least that is what the web interface reads out.
-
No Actually, it just helped. Things started working right when i put the M667 S0 and the M500. I can set the M572 D0 S0.00 to something other then zero. Whats a Recommended value to start with?
Try S values between 0.05 and 0.25. If you are using more than about 2mm of retraction then be prepared to reduce it when you use high S values. For example, using S0.25 will add about 1mm of retraction at the end of a fast printing move.
-
Ok, i set the pressure advance to this, and started a test print
M572 D0 S0.05 ; Set extruder 0 pressure advance
M572 D1 S0.05 ; Set extruder 1 pressure advanceWhen i got to the 1.00mm Z height, the Y axes started to jump, as if it was moving, braking, moving, braking. i killed the print as it was getting pretty load and i was afraid it was going to brake the printer.
