Working with variables in Gcode?

Danal

This post is deleted!

T3P3Tony

Looks like you want to have a tool change macro:
https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareCartesianPrinter#Section_Tool_change_files

WarriorMe

If i understand correctly, you are trying to write a Gcode to move the second nozzle to the correct position?

You don't actually need to do that. Setting the right tool offset is enough, though you need to include a command to lift the printhead in the "tpre" macro (which you can access in the system editor) to prevent the idle printhead from colliding with the bed when it's deploying.

You also need to put the commands required to actually deploy or retract the nozzle in the "tpost" macros.

RudydG

I know i can use the macro's, that is not the poitn.

This is the code i use to switch head (ultimaker head) it is rather complicated, and when i change something, i have to rewrite this entire code...
That is why i want to use some variables.
Many thanks,
Rudy
G1 X280 Y5 F20000 ;velige zone
G1 X280 Y23 F5000 ;ga voor gleuf
G1 X287.1 Y23 F5000 ; ga in gleuf
G1 X287.1 Y16 F5000 ;beweeg eerste stuk
G1 X285.1 Y9 F5000 ; beetje uit
G1 X284.1 Y2 F5000 ;vrij
G1 X280 Y5 F5000

dc42

@rudydg said in Working with variables in Gcode?:

I know i can use the macro's, that is not the poitn.

This is the code i use to switch head (ultimaker head) it is rather complicated, and when i change something, i have to rewrite this entire code...
That is why i want to use some variables.
Many thanks,
Rudy
G1 X280 Y5 F20000 ;velige zone
G1 X280 Y23 F5000 ;ga voor gleuf
G1 X287.1 Y23 F5000 ; ga in gleuf
G1 X287.1 Y16 F5000 ;beweeg eerste stuk
G1 X285.1 Y9 F5000 ; beetje uit
G1 X284.1 Y2 F5000 ;vrij
G1 X280 Y5 F5000

I'm sorry, the extent of my Dutch/Flemish is "twee biertjes alstublieft". Can you translate the comments for me?

whosrdaddy

@rudydg :

you could switch to relative positioning after the first G1 command, this way you only would need the absolute coordinates (Translated comments for @dc42 ) :

G1 X280 Y5 F20000 ; safe zone
G91 ; relative positioning
G1 Y18 F5000 ;position in front of the slot
G1 X7.1 F5000 ; go in the slot
G1 Y-7 F5000 ;move first part
G1 X-2 Y-7 F5000 ; almost out
G1 X-1 Y-7 F5000 ; free
G90; absolute positioning
G1 X280 Y5 F5000

RudydG

This post is deleted!

RudydG

@whosrdaddy said in Working with variables in Gcode?:

@rudydg :

you could switch to relative positioning after the first G1 command, this way you only would need the absolute coordinates (Translated comments for @dc42 ) :

G1 X280 Y5 F20000 ; safe zone
G91 ; relative positioning
G1 Y18 F5000 ;position in front of the slot
G1 X7.1 F5000 ; go in the slot
G1 Y-7 F5000 ;move first part
G1 X-2 Y-7 F5000 ; almost out
G1 X-1 Y-7 F5000 ; free
G90; absolute positioning
G1 X280 Y5 F5000

Ok, thank you, did not see you translated for me.
And will have a go with this method. Indeed yes, only one set of coordinates to manipulate in this situation.

RudydG

I'm sorry, the extent of my Dutch/Flemish is "twee biertjes alstublieft". Can you translate the comments for me?

whosrdaddy helped me out i guess.
Fun to see "twee biertjes alstublieft" always works ;-);-);-)

I have a second question,
How s the sequence of the toolchange files, i think there are 6 files, but i have some issues there also, and i don't find a clear explanation about is.

whosrdaddy

@rudydg said in Working with variables in Gcode?:

I have a second question,
How s the sequence of the toolchange files, i think there are 6 files, but i have some issues there also, and i don't find a clear explanation about is.

Look at the section "setting up the tool change files" of this documentation link.