Z axis motors not getting power
-
Hi,
I have my motors hooke up to the my duex and they are set under z axis with the M584 command but they still arent getting power because under the machine properties tab it says their motor current is 0. how would i change that to 800?
Here is my config
Thanks
; Configuration file for Duet WiFi (firmware version 1.17 to 1.19)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Thu Mar 29 2018 21:22:13 GMT-0400 (Eastern Daylight Time)
; Custom settings
M584 X0 Y1:4 Z5:6:7:8:2 E3:9; General preferences
G90 ; Send absolute coordinates…
M83 ; ...but relative extruder movesM667 S1 ; Select CoreXY mode
; Network
M550 PUnderground Printing- Jumbo ; Set machine name
M552 S1 ; Enable network
M587 S"KQVQM" P"SVLFBZMC3PK8893X" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M569 P4 S0 ; Drive 4 goes back
M350 X32 Y32 Z32 E16 I1 ; Configure microstepping with interpolation
M92 X160 Y160 Z4000 E420 ; Set steps per mm
M566 X900 Y900 Z12 E120 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z180 E1200 ; Set maximum speeds (mm/min)
M201 X500 Y20 Z250 E250 ; Set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 U0 Z0 S1 ; Set axis minima
M208 X838.2 Y762 Z1117.6 S0 ; Set axis maxima; Endstops
M574 X1 Y2 S0 ; Set active low endstops; Z-Probe
M558 P0 H5 F120 T6000 ; Disable Z probe but set dive height, probe speed and travel speed
M557 X15:823.2 Y15:747 S20 ; Define mesh grid; Heaters
M140 H-1 ; Disable heated bed
M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C; Fans
M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C -
The Machine Properties tab doesn't take account of axis mappings, so it isn't giving you the true picture.
-
do you know any reason it wouldn't be moving either up or down
-
Is the DueX5 definitely getting VIN power?
Does the Settings General page of DWC mention the DueX5?
Does M122 list the status of 10 drives, or only 5?
