Inductive sensor

npm1

Ok according to the duet manual i connect a resistor between the ground and signal, then the power to a Vin socket.

Now, how many ohms resistor should it be.

I currently have 240ohm spare one laying around.

dc42

No, the Duet instructions don't say that. See https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe#Section_Connecting_different_types_of_Z_probe.

npm1

Ok so i drew a diagram, which way should i go with connecting the inductive sensor.

Kind Regards

dc42

Is it a PNP or an NPN output sensor?

npm1

Its NPN

dc42

Then you don't need resistors, just a small signal Schottky diode as described in the page I linked too.

npm1

Would this setup work?

Kozlow

Hey npm1

I just hooked a probe similar to this yesterday.
dc42 helped me out with a problem that I was having.
You should have a read of that thread.
https://www.duet3d.com/forum/thread.php?id=4490.

Are you planning on using the probe as an end stop too?
Because I hooked mine up using E0 endstop pins, I'm not sure that it will work as
an endstop if you use the probe pins.

Hope this helps
Steve

dc42

Yes that diagram looks right. Use probe type P5 in the M558 command.

parovoZZ

Port will not burn out?

Kozlow

@dc42:

Yes that diagram looks right. Use probe type P5 in the M558 command.

Hey dc42, just so i understand, if you use the probe connector can you still use the probe as an endstop?
Is there any difference besides for the firmware settings between using the Z probe pins vs the E0 stop pin?

dc42

Yes there is. See https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareCartesianPrinter#Section_Homing_Z.

npm1

thks for the heads up on the pictures,

@kozlow: anything can be used as an endstop as long as the M558 and G31 commands are defined correctly

Kozlow

@npm1:

thks for the heads up on the pictures,

@kozlow: anything can be used as an endstop as long as the M558 and G31 commands are defined correctly

Right, i realize that you can use a probe as an endstop, that's how mine is set up.
What i didn't know was if it worked the same when the probe was hooked up to the probe pins. Because when i set up my NPN sensor the wiki said to use the E0 stop pin.
The wiki must be out dated. That must be for previous hardware that didn't have probe pins.

dc42

An NPN-output sensor can be connected to the E0 endstop input, E1 endstop input, Z endstop input (if it is free) or Z probe connector. You choose the P parameter in the M558 command to tell it which one.

Kozlow

@dc42:

An NPN-output sensor can be connected to the E0 endstop input, E1 endstop input, Z endstop input (if it is free) or Z probe connector. You choose the P parameter in the M558 command to tell it which one.

Ok, thanks for the clarification. I understand now. Lol

npm1

Great so I have successfully got the 5v version of this sensor, literally plug and play, the issue i have is the first layer i.e. some of the filament isnt smushed down enough to the point where i could rub my finger against the filament and have it come of the build plate

Isnt bed leveling with a sensor supost to give perfect first layer height.

my bed.g file

[[language]]
; bed.g
; called to perform automatic bed compensation via G32
M561				       ;Clear any bed transform
G28 ; home all
G90 				               ; Back to absolute positioning ;G91 ; relative mode
M557 X0:150 Y13:180 S30     ; Define mesh grid
G1 Z4 F200 ; move Z 4mm for clearance
G90 ;absolute mode
;M280 p3 S160 I1 ; Clear any alarms ;M401 ; In lieu of macro - call GCode for deploy probe
G29 S0; run auto bed mesh level
M374 	; Save Mesh Data
;M402 ; In lieu of macro - call GCode to retract probe

My Home Z file

[[language]]
T0 ; select first hot end
G91 ; Relative coordinates
G1 Z5 F200 ; Lower bed.
G4 P500 ; Dwell for 500ms - to ensure bed is down
G90 ; Absolute positioning
G1 X10 Y15 F300 ; Go to first bed probe point and home the Z axis
;M401; M280 P3 S10 I1 ; Lower Z probe (BLTouch)
G30; Calibrate Z-axis
;M402; M280 P3 S10 I1; Retract Probe
;G92 Z2.5; PLA. higher g92 means that 0 is lower down on the z axis
G92 Z1.55; ABS. higher g92 means that 0 is lower down on the z axis

My Heightmap

please help

Excuse the Bltouch comments I removed it from my printer since it was always giving me inconsistent z heights and massive variations in the heightmap.

With the bltouch i had to continues change the G92 height. With the new sensor I barely touch this code.

Please Help

npm1

I have successfully soldered and added the new sensor to my printer, looking forward to better consistency, how ever this is connected through the endstop connector rather than the probe connector.

What is the difference between the probe connector and the axis endstop connectors

this time i am looking to post more heightmaps.

dc42

@npm1 said in Inductive sensor:

I have successfully soldered and added the new sensor to my printer, looking forward to better consistency, how ever this is connected through the endstop connector rather than the probe connector.

What is the difference between the probe connector and the axis endstop connectors

this time i am looking to post more heightmaps.

An NPN output sensor can be connected to either an endstop connector or the z probe connector. It doesn't matter which as long as you tell that firmware in the M558 command how you have connected it.

npm1

At the moment when i get the sensor connected to the probe pins, the z probe trigger value is alway 1000, when the sensor is touching the aluminium, the reading is still 1000.
The firmware is set as follow:

; Endstops
M574 X1 Y1 S1 ; Set active low endstops
M574 Z1 S0 ;(S1)
M558 P5 X0 Y0 Z1 H10 F80 I1 T6000 ; for inductive sensor, Set Z probe type to switch, the axes for which it is used and the dive height + speeds
M557 X0:170 Y13:180 S25; Define mesh grid
G31 P500 X0 Y0 Z0; Set Z probe trigger

m119 is not reporting the probe at its minimum point

please help