Converting the Duet WiFi to use an external antenna

fma

Ok, I just changed my wifi module, but I can't set ssid/password (get "Bad or missing parameter"). Here are the logs:

>>> M997 S1
SENDING:M997 S1
Trying to connect at 460800 baud:
 success
Erasing 302928 bytes...
Uploading file...
5% complete
10% complete
15% complete
20% complete
25% complete
30% complete
35% complete
40% complete
45% complete
50% complete
55% complete
60% complete
65% complete
70% complete
75% complete
80% complete
85% complete
90% complete
95% complete
Upload successful
>>> M552 S0
SENDING:M552 S0
WiFi module started
>>> M587 Sxxx Pxyyy
SENDING:M587 Sxxx Pyyy
M587: Bad or missing parameter
>>> M122
SENDING:M122
=== Diagnostics ===
Used output buffers: 1 of 32 (9 max)
=== Platform ===
RepRapFirmware for Duet WiFi version 1.20beta8 running on Duet WiFi 1.0
Board ID: 08DDM-9FAM2-LW4S8-6JTDG-3SD6Q-13YRX
Static ram used: 15488
Dynamic ram used: 99136
Recycled dynamic ram: 64
Stack ram used: 4328 current, 5532 maximum
Never used ram: 10852
Last reset 00:19:36 ago, cause: reset button or watchdog
Last software reset reason: User, spinning module GCodes, available RAM 11504 bytes (slot 4)
Software reset code 0x0003, HFSR 0x00000000, CFSR 0x00000000, ICSR 0x00400000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
[ERROR] Error status: 0

Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 26.4, current 27.2, max 27.4
Supply voltage: min 1.7, current 1.7, max 1.7, under voltage events: 0, over voltage events: 0
Driver 0: ok
Driver 1: ok
Driver 2: ok
Driver 3: ok
Driver 4: ok
Date/time: 1970-01-01 00:00:00
Cache data hit count 1442288766
Slowest main loop (seconds): 3.074205; fastest: 0.000033
=== Move ===
MaxReps: 0, StepErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heater = 0, chamber heater = -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
Network state is running
WiFi module is idle
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.20b9
WiFi MAC address 5c:cf:7f:61:99:c5
WiFi Vcc 3.35, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 32376
HTTP sessions: 0 of 8
Socket states:  0 0 0 0 0 0 0 0
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)

Any idea?

dc42

Are you putting the ssid and password inside double quote characters?

fma

Yes. I tried with Pronterface (using single quote to prefix each lower case char), and with minicom. Same error each time.

Whatever I use as S/P values, I get the error.

Did I fry the esp module? I don't think, as the firmware was successfully updated, but…

fma

I just upgraded to lastest stable firmwares (1.20), and all is now working fine!

fma

I have a question… M122 returns:

WiFi signal strength -73dBm

But my router says:

Signal    Noise     RX Rate       TX Rate
-59 dBm   -89 dBm   54.0 Mbit/s   65.0 Mbit/s

Why is there such difference in signal level? In fact, while I'm now using the ESP-07 with a +6dB gain antenna, the signal level returned by M122 didn't changes that much (I think I was around -75dB before)…

garyd9

Large differences is wifi signal strength are normal for differing wifi devices. Each one "hears" the other differently. This can be due so many different factors it's impractical to enumerate. Usually, it's different radio power, different antennas, or different propagation paths.

In your case, it appears the router has "bigger ears" (better antenna.)

fma

Ok, I see.

But why switching from the default ESP (no antenna) to the new one (6dB gain antenna) didn't change that much the signal strength returned by the Duet?

I don't have signal values given by the router with the default ESP (didn't think to read it at the time); so I don't know if it really changed. But the thing is I know have a much better connection: transfers are very fast and I don't get any disconnection anymore.

dc42

If M122 is telling you that the signal strength is -73dBm now, that is already very low. If it was even lower before, that would explain the disconnections you had.

Which wifi channel is your router set to? Does the reported signal strength vary if you switch between channels 1, 6 and 11?

fma

Yes, it is low. But, as said, real transmissions work much better and faster, now. And no more disconnection.

I will make tests with different channels (I think I'm on channel 1 - the router is in auto and chose this one).

parovoZZ

Hi!

I have WiFi signal strength -61dBm in three meters from the router. The ESP-07 has a very very weak antenna ((
I will change to ESP-07S or connect external to ESP-07.
Laptop, iPhone, Nokia etc. - everything works fine.

fma

I used a wifi analyser on my phone, and noticed that there where 3 other AP on channel 1. In fact, it depends where I am in the house, and on the AP side, they are not detected. So the AP chose this channel. But on the printer side, they where as powerfull as my AP!

I moved to channel 3, unused by other wifi AP, and I now have -66dB strength…

ephemeris

Will this be available as a build option?

martins

ESP-07S sold out in RS-online how thats possible

S1lencer

Hi, i have a problem since i changed the Module.
I can only connect to the Duet Wifi in Accesspoint mode. If i change it to M552S1 it only says: Wifi reported error: no known networks found.
The wifi is defenitly present.
Did flash the right firmware files main as also the Wifiserver one.
Running 1.21

Anyone a clue why this could be?

S1lencer

Got the Problem solved.
David, i think the firmware 1.21 has a problem with loading the M587 with the Router data from the config.g to the remembered list.
Got my problem solved with Repetier host, did send the M587 with ssid and password via g-code console.

dc42

@S1lencer:

Got the Problem solved.
David, i think the firmware 1.21 has a problem with loading the M587 with the Router data from the config.g to the remembered list.
Got my problem solved with Repetier host, did send the M587 with ssid and password via g-code console.

How did you send the M587 command originally?

S1lencer

Via the config script

dc42

Sending M587 in config.g isn't going to work, because the wifi module doesn't get enabled until the end of running config.g. That's why I suggest using a macro to send those commands.

S1lencer

Ok for the next time i will do that.
Should be mentioned in the Wiki.