Motor brake not working on expansion board
-
@mike_b we recently released 3.5.3-rc.1 so I suggest you try that.
-
@dc42 Thank you! This is fantastic. I'll try it out tomorrow and report any bugs in the beta channel. Thanks again!
-
@dc42 apologies up front if I'm missing something obvious here. However, in your dropbox, I don't see the
Duet3_SBCiap32_Mini5plus.bin
file which, I assume, I would a 3.5.3-rc.1 version off to test if this bug has been resolved? Or, is it safe to test withDuet 3 Expansion Mini5plus
running at 3.5.2? -
-
Hi @jay_s_uk, unfortunately I don't see
Duet3_CANiap32_Mini5plus.bin
in the link provided. Am I missing something? -
@mike_b DSF should handle the SBC IAP file, they aren't part of a normal release
-
@jay_s_uk When you say "DSF should handle the SBC IAP file" do you mean that I'll be able to find the .bin file in the DSF git repo?
-
@mike_b when you sudo apt update/upgrade, everything gets pulled down and automatically updated. so I suppose I should say the DSF repository (not git)
-
@jay_s_uk ah, Ok, got it, thank you! So I guess that mean I'll have to figure out my second issue https://forum.duet3d.com/post/344169, for some reason, despite switching to the unsteady deb repo (i.e
deb https://pkg.duet3d.com/ unstable-3.5 armv7
in my sources, running apt update/upgrade doesn't get me 3.5.3-rc -
@dc42 How do we update to this if we're running in SBC mode? The M997 commands don't work.
-
@p8blr you can't at the moment
-
Hey @jay_s_uk when you say "you can't at the moment" do you mean you can't at the moment because of a bug? Or do you mean you can't update to an
-rc
release in SBC in general? I ask because there does seem to be a version 3.5.3-rc1 in the repo here so I'm not really sure what the issue is. Could you help me understand? -
@mike_b just wait for @chrishamm to respond. You can usually upgrade to RC versions but it's obviously not working so be patient
-
Hey @jay_s_uk Thanks for your feedback! I truly appreciate everyone’s input and am happy to wait for a response Thanks again!
-
@mike_b It's now available via the package feeds, apologies for the delay.
-
Thanks @chrishamm, my entire system is now running 3.5.3-rc.1 as shown here
Unfortunately @dc42 I'm getting the same bug as before:
05/09/2024, 14.02.03 -Error in start-up file config.g line 156: M569.7: 05/09/2024, 14.02.03 -Error: M569.7:
Interestingly, I don't see these errors after power cycling the board and the SBC. That error only shows up when I do an emergency stop or chose "restart mainboard" or "run config file" after editing the config file. Although I guess I'm not getting those messages after a power cycle because DWC starts up only after the error, so doesn't show up in the console?
@dc42 also, I just realized that my particular issue was never mirrored on github - or mentioned in the release notes - so now I'm wondering if this issue got confused with this one?
Looking through the changelogs of previous releases, I see this limitation mentioned for 3.4.0RC1 but it's never mentioned again:
M569.7 (configure driver brake port) is supported, initially on the main board only -
@mike_b M569.7 is supported on expansion boards too, since version 3.5.0 AFAIR.
-
-
Hey @dc42 in case it's helpful, I am reiterating the issue here:
in 3.5.2 and 3.5.3-rc.1 this command fails:
M569.7 P40.0 C"40.out5" S25
while a similar command on the main board works fine:
M569.7 P0.0 C"out5" S25
-
@mike_b in what way does it fail? Does it return an error message, or return no message but the brake doesn't get activated when you use M17 and M18 to enable and disable the motor?
What is the response if you send M569.7 P40.0 after sending the original M569.7 command?
Have you verified that the port, wiring and brake are OK by configuring the port as a GpOut port instead and using M42 to turn the brake on and off?
What expansion board are you using?
Have you tried doing the same thing using 3.6.0-alpha.5 firmware?