New firmware 1.20 Release Candidate 2 - please try it!

deckingman

@crishamm
Ref my earlier post about extruder drive position in the Machine Status panel, I can now confirm that the behaviour is not limited to printing but appears to affect any extruder move. To elaborate, I ran home all which zeros the extruder positions. Then set active temperature for all tools to 180 and extruded 20mm of filament from each drive in turn. After using drive 0, the Extruder drive panel showed D0 at 0.0, D1 at 0.0, D2 at 20.0, D3 at 0.0 and D4 at 0..0. Using drive 1 shows 20.0 for Drive 3, and using drive 2 shows 20.0 for drive 4. Using drives 3 and 4 has no effect on the values shown in the machine status panel.

To be clear, the extruder drives are all working as expected but the drive position as reported in the Machine Status Panel is incorrect. The effect is that plus 2 is being added to the drive number so the value for Drive 0 is being applied to Drive2 in the panel, the value for Drive 1 is being applied to Drive 3 etc.

Cheers

Ian

Gosu

i updated from RC1 to RC2 then it stopped running with wifi and i used the new www file to fix the problem

now i can only control my printer via wifi for 5 minutes(with constant disconnects) and i was able to start a print
but the printer stopped beeing able to connect via webhost
only seldomly beeing able to connect

i would love to post my current version but it wont let me connect
its FW RC2
Wifi Beta10 i believe
and RC3 Webclient

Forgvn77

Pause print and resume failed for me from the PanelDue. The hot end resumed extruding a couple layers above the print. Running 1.20RC2 and latest DWC release candidate,

Iirai

When I try to connect to DWC I get this error:
Could not establish a connection to the Duet firmware! Please check your settings and try again.

I'm able to ping the DuetWiFi, wifi signal is -59, it's on a static Ip and I confirmed that the mac address is correct . Am I missing something obvious?

Firmware: 1.20-RC2
DuetWiFiServer: 1.20beta10
DWC: 1.20-RC3

Gone2Far

Admittedly I do not stress the Duet much, but FWIW, RC2 is working well for me.

dc42

@Iirai:

When I try to connect to DWC I get this error:
Could not establish a connection to the Duet firmware! Please check your settings and try again.

I'm able to ping the DuetWiFi, wifi signal is -59, it's on a static Ip and I confirmed that the mac address is correct . Am I missing something obvious?

Firmware: 1.20-RC2
DuetWiFiServer: 1.20beta10
DWC: 1.20-RC3

1. Did you install DuetWiFiServer.bin twice as suggested in the upgrade notes?

2. If you send M552 S1 from USB or PanelDue then it will report success/failure of the attempt to connect to your router.

dc42

@Gone2Far:

Admittedly I do not stress the Duet much, but FWIW, RC2 is working well for me.

Thanks for the feedback! Which Duet do you have?

dc42

@Forgvn77:

Pause print and resume failed for me from the PanelDue. The hot end resumed extruding a couple layers above the print. Running 1.20RC2 and latest DWC release candidate,

Thanks for the feedback. I'll test pause/resume again.

dc42

@Gosu:

i updated from RC1 to RC2 then it stopped running with wifi and i used the new www file to fix the problem

now i can only control my printer via wifi for 5 minutes(with constant disconnects) and i was able to start a print
but the printer stopped beeing able to connect via webhost
only seldomly beeing able to connect

i would love to post my current version but it wont let me connect
its FW RC2
Wifi Beta10 i believe
and RC3 Webclient

Did you install DuetWiFiFirmware twice as recommended in the upgrade notes?

AS-3D Druck

The Dark Theme on the new Webcontol is a little bit wrong.

Screenshot:
https://gyazo.com/5d01aed4163234081552f63a99b2f76c

dc42

@AS-3D:

The Dark Theme on the new Webcontol is a little bit wrong.

Screenshot:
https://gyazo.com/5d01aed4163234081552f63a99b2f76c

Try updating DWC to 1.20RC3.

AS-3D Druck

@dc42:

@AS-3D:

The Dark Theme on the new Webcontol is a little bit wrong.

Screenshot:
https://gyazo.com/5d01aed4163234081552f63a99b2f76c

Try updating DWC to 1.20RC3.

There is no DWC 1.20RC3 here: https://github.com/dc42/RepRapFirmware/tree/dev/Release/Duet-WiFi/Edge
or here: https://github.com/chrishamm/DuetWebControl

//Edite
THX now i found it (Duet Wifi): https://github.com/dc42/RepRapFirmware/blob/dev/Release/Duet-WiFi/Edge/DuetWebControl-1.20-RC3.zip

dc42

I've just released 1.20RC3. This has only minor changes from 1.20RC2.

The following have been reported in this thread:

1. "Starting with Beta11, with the M584 changes, with the U axis hidden if I run G29 the printer starts probing, but after the first row the U drive, which is my second Z motor starts moving up rather than down."

I thought I had asked for more detail about this issue, but it looks like I didn't. Has anyone else seens a similar issue? Hiding the U axis should make no difference to the behaviour of the Z axis, but it will prevent explicit U moves being made.

2. Various WiFi disconnection issues. Please note the instructions to install DuetWiFiServer-1.20b10 twice. You can use older DuetWiFiServer versions with RRF 1.20RC3 if necessary, but if you do then the M587 command to list configured wifi networks may not work. I expect to have DuetWiFiServer 1.20beta11 available early next week.

3. A report that pause/resume caused the print to resume too high. I have tested this on 2 printers and I can't reproduce it.

4. Various DWC issues, which I believed are resolved in DWC 1.20-RC3.

AS-3D Druck

I got a Problem to open a Directory on G-Code Files:

[[language]]
A JavaScript error has occurred so the web interface has closed the connection to your board. It is recommended to reload the web interface now. If this happens again, please contact the author and share this error message:

Version: 1.20-RC3
Message: Uncaught TypeError: Cannot read property 'match' of undefined
URL: http://d-bot.local/js/dwc.js
Line: 2015:27
Error object: {}

Only this Directory makes Problemes everything else works.

deckingman

@dc42:

….................
4. Various DWC issues, which I believed are resolved in DWC 1.20-RC3.

Some have been resolved but the extruder position issue that I reported above is still outstanding.

Gone2Far

@dc42:

@Gone2Far:

Admittedly I do not stress the Duet much, but FWIW, RC2 is working well for me.

Thanks for the feedback! Which Duet do you have?

Duet WiFi, with smart effector and 7" panel due.

dc42

@AS-3D:

I got a Problem to open a Directory on G-Code Files:

[[language]]
A JavaScript error has occurred so the web interface has closed the connection to your board. It is recommended to reload the web interface now. If this happens again, please contact the author and share this error message:

Version: 1.20-RC3
Message: Uncaught TypeError: Cannot read property 'match' of undefined
URL: http://d-bot.local/js/dwc.js
Line: 2015:27
Error object: {}

Only this Directory makes Problemes everything else works.

Is there anything unusual about that directory, for example its name?

Dougal1957

@dc42:

I've just released 1.20RC3. This has only minor changes from 1.20RC3.

The following have been reported in this thread:

1. "Starting with Beta11, with the M584 changes, with the U axis hidden if I run G29 the printer starts probing, but after the first row the U drive, which is my second Z motor starts moving up rather than down."

I thought I had asked for more detail about this issue, but it looks like I didn't. Has anyone else seens a similar issue? Hiding the U axis should make no difference to the behaviour of the Z axis, but it will prevent explicit U moves being made.

2. Various WiFi disconnection issues. Please note the instructions to install DuetWiFiServer-1.20b10 twice. You can use older DuetWiFiServer versions with RRF 1.20RC3 if necessary, but if you do then the M587 command to list configured wifi networks may not work. I expect to have DuetWiFiServer 1.20beta11 available early next week.

3. A report that pause/resume caused the print to resume too high. I have tested this on 2 printers and I can't reproduce it.

4. Various DWC issues, which I believed are resolved in DWC 1.20-RC3.

David

A Couple of Typos first in this post first line V1.20RC3 has minor changes to 1.20RC3

And in the changeling latest release titled as 1.20RC2

Doug

T-Printer

I still have at lot of Communication Error (before with 1.18, ther was no problems with the WiFi)
DuetWiFiServer ver. 1.20B10 Install twice as DC42 say
Web Interface ver. 1.20-RC3
Duet FirmWare ver. 1.20RC3
My Wifi ruter is a ASUS RT-AC87U, and is firmware is up to date. good signal -55
It just go on and off. On the Paneldue is say Wifi Reported Error Lost Connection Auto Reconnect, and Auto Reconnect Succeeded about every 1 - 2 min
On the webinterface most of the time, I have Communication Error, then I can reconect, but after Max 1min I am off aging..
Anny solution to this?
Kent

AS-3D Druck

@dc42:

@AS-3D:
I got a Problem to open a Directory on G-Code Files:
[[language]]
A JavaScript error has occurred so the web interface has closed the connection to your board. It is recommended to reload the web interface now. If this happens again, please contact the author and share this error message:

Version: 1.20-RC3
Message: Uncaught TypeError: Cannot read property 'match' of undefined
URL: http://d-bot.local/js/dwc.js
Line: 2015:27
Error object: {}
Only this Directory makes Problemes everything else works.
Is there anything unusual about that directory, for example its name?

Got it, i used letters like äüß and he converted that to strange Symbols.
After renaming everything works again.