Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Wifi problem since replacing SD card with new Firmware

    Scheduled Pinned Locked Moved
    Firmware installation
    3
    18
    474
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • mesacrashundefined
      mesacrash @mesacrash
      last edited by

      @mesacrash I meant to say NO www folder.

      1 Reply Last reply Reply Quote 0
      • Phaedruxundefined
        Phaedrux Moderator @mesacrash
        last edited by

        @mesacrash said in Wifi problem since replacing SD card with new Firmware:

        I got a new one and installed frirmwre 3.4.6

        How did you install 3.4.6? To update the firmware requires more than just putting it on the SD card. The firmware gets flashed to the board itself. The SD card just holds the files.

        @mesacrash said in Wifi problem since replacing SD card with new Firmware:

        Your Duet rejected the HTTP request: page not found
        Check that the SD card is mounted and has the correct files in its /www folder".

        What is in the WWW folder? This is where the DWC files reside, and the version of the files there needs to match the version for your firmware.

        Since the board is still reporting 3.4.2, the firmware update hasn't been applied. So take a look at this link to see how to flash the board. https://docs.duet3d.com/en/User_manual/RepRapFirmware/Updating_firmware

        Then replace the files in your WWW folder with the DWC files from the firmware release. 3.4.6 in your case.

        And just in case you're missing something else from the new SD card, take a look here: https://docs.duet3d.com/en/User_manual/RepRapFirmware/SD_card

        Z-Bot CoreXY Build | Thingiverse Profile

        mesacrashundefined 6 Replies Last reply Reply Quote 0
        • mesacrashundefined
          mesacrash @Phaedrux
          last edited by mesacrash

          @Phaedrux

          @Phaedrux
          I am still getting the same error message and I am not able to connect to the printer on my browser. It says, "Error: M997: File 0:/firmware/DuetWiFiServer.bin not found", but it is there.

          From YAT:
          M552 S-1.
          ok
          M552
          WiFi module is disabled
          ok
          M552 S0
          ok
          WiFi module started
          M552
          WiFi module is idle
          ok
          M587 S"NETGEAR31" P"giftedbanana800"
          ok
          M587
          Remembered networks:
          TNCAPF2FD81 IP=192.168.1.8 GW=0.0.0.0 NM=0.0.0.0
          <ETX>[Warning: "F1h 01h" is a byte sequence outside the Unicode basic multilingual plane (plane 0)! Only Unicode plane 0 is supported by .NET Framework and thus YAT (yet).] IP=253.242.1.0 GW=4.47.2.0 NM=253.242.1.0
          NETGEAR31 IP=0.0.0.0 GW=0.0.0.0 NM=0.0.0.0
          ok
          M552 S1
          ok
          WiFi module is connected to access point NETGEAR31, IP address 192.168.1.8
          M997 S1
          Error: M997: File 0:/firmware/DuetWiFiServer.bin not found
          ok

          1 Reply Last reply Reply Quote 0
          • mesacrashundefined
            mesacrash @Phaedrux
            last edited by

            @Phaedrux I discovered a problem with my PC reading the card. It was intermittently reading/not reading. I think I have solved the problem and will try again. Please disregard my last message. I will get back with you, once I know what is going on. Thank you

            1 Reply Last reply Reply Quote 1
            • mesacrashundefined
              mesacrash @Phaedrux
              last edited by

              @Phaedrux 6ed3bb94-6f99-4172-b3ab-96a778a32a43-image.png

              1 Reply Last reply Reply Quote 0
              • mesacrashundefined
                mesacrash @Phaedrux
                last edited by

                @Phaedrux Please advise.

                1 Reply Last reply Reply Quote 0
                • mesacrashundefined
                  mesacrash @Phaedrux
                  last edited by

                  @Phaedrux
                  SD card 0 not detected, interface speed: 30.0MBytes/sec
                  SD card longest read time 0.0ms, write time 0.0ms, max retries 0

                  droftartsundefined 1 Reply Last reply Reply Quote 0
                  • mesacrashundefined
                    mesacrash @Phaedrux
                    last edited by

                    @Phaedrux
                    M39
                    Error: M39: No SD card mounted in slot 0
                    ok

                    1 Reply Last reply Reply Quote 0
                    • droftartsundefined
                      droftarts administrators @mesacrash
                      last edited by

                      @mesacrash It is not finding the SD card. Make sure the SD card is in, and reset the board. Send M122 and post the reply. You can cut and paste from YAT into your reply, in between 'code' quotes (</> formatting in the message window) which is much easier and more readable than taking a screenshot.

                      If the SD card is in, how big is it, and how is it formatted? See https://docs.duet3d.com/en/User_manual/RepRapFirmware/SD_card#formatting

                      To flash the firmware, you also need the IAP (In Application Programmer) binary file in the /firmware folder. You need to use the version of this that matches the firmware that is currently on your board. Most likely using the one from RRF 3.4.5 will be fine. Get the "Duet2_SDiap32_WiFiEth.bin" file from https://github.com/Duet3D/RepRapFirmware/releases/tag/3.4.5 and put it in the /firmware folder.

                      Cartesian bed-slinger with Duet 3 Mini 5+ WiFi and 1LC : RRP Fisher Delta v1 with Duet 2 Maestro : TronXY X5S with Duet 3 MB6HC and Roto toolboard

                      mesacrashundefined 3 Replies Last reply Reply Quote 1
                      • mesacrashundefined
                        mesacrash @droftarts
                        last edited by droftarts

                        @droftarts

                        M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.6 (2023-07-21 14:08:28) running on Duet WiFi 1.02 or later
Board ID: 0JD2M-9F8TA-GJ4TJ-6JTD4-3S46T-16UL6
Used output buffers: 1 of 26 (1 max)
=== RTOS ===
Static ram: 23896
Dynamic ram: 73392 of which 0 recycled
Never used RAM 14792, free system stack 184 words
Tasks: NETWORK(ready,6.8%,513) HEAT(notifyWait,0.0%,388) Move(notifyWait,0.0%,363) MAIN(running,93.0%,602) IDLE(ready,0.2%,30), total 100.0%
Owned mutexes: USB(MAIN)
=== Platform ===
Last reset 00:08:47 ago, cause: reset button or watchdog
Last software reset at 2023-10-17 18:21, reason: User, GCodes spinning, available RAM 12876, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 0
MCU temperature: min 22.1, current 22.7, max 23.7
Supply voltage: min 24.3, current 24.3, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min n/a
Driver 1: standstill, SG min n/a
Driver 2: standstill, SG min n/a
Driver 3: standstill, SG min n/a
Driver 4: standstill, SG min n/a
Driver 5: 
Driver 6: 
Driver 7: 
Driver 8: 
Driver 9: 
Driver 10: 
Driver 11: 
Date/time: 1970-01-01 00:00:00
Cache data hit count 4294967295
Slowest loop: 4.44ms; fastest: 0.19ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.5ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is ready with "M122" in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== Network ===
Slowest loop: 0.29ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 0 of 8
= WiFi =
Interface state: disabled
Module is disabled
Failed messages: pending 0, notready 0, noresp 0
Socket states: 0 0 0 0 0 0 0 0
ok
                        droftartsundefined 1 Reply Last reply Reply Quote 0
                        • mesacrashundefined
                          mesacrash @droftarts
                          last edited by

                          @droftarts
                          Every time I formatted an SD card with the SD Card Formatter, My main PC said Windows wouldn't open it. So, I used Windows Formatter, not Quick.

                          1 Reply Last reply Reply Quote 0
                          • mesacrashundefined
                            mesacrash @droftarts
                            last edited by

                            @droftarts
                            The reset must have been the answer. It is currently burning to the board.

                            droftartsundefined 1 Reply Last reply Reply Quote 0
                            • droftartsundefined
                              droftarts administrators @mesacrash
                              last edited by

                              @mesacrash
                              The M122 says firmware version is 3.4.6, so not much point updating it.
                              It also says "SD card 0 detected, interface speed: 20.0MBytes/sec" so that seems to be okay. Try sending M39 again.
                              Your WiFi module is disabled, so I can't tell if that is working or not.
                              Is there a config.g in the /sys folder of the SD card?

                              Ian

                              Cartesian bed-slinger with Duet 3 Mini 5+ WiFi and 1LC : RRP Fisher Delta v1 with Duet 2 Maestro : TronXY X5S with Duet 3 MB6HC and Roto toolboard

                              mesacrashundefined 1 Reply Last reply Reply Quote 0
                              • droftartsundefined
                                droftarts administrators @mesacrash
                                last edited by

                                @mesacrash said in Wifi problem since replacing SD card with new Firmware:

                                @droftarts
                                The reset must have been the answer. It is currently burning to the board.

                                If you eject the SD card, when you put it back in, you either need to remount it with M21, or reset the board.

                                Ian

                                Cartesian bed-slinger with Duet 3 Mini 5+ WiFi and 1LC : RRP Fisher Delta v1 with Duet 2 Maestro : TronXY X5S with Duet 3 MB6HC and Roto toolboard

                                mesacrashundefined 1 Reply Last reply Reply Quote 0
                                • mesacrashundefined
                                  mesacrash @droftarts
                                  last edited by

                                  @droftarts No, my old card crapped out on me, so I'm starting fresh.

                                  1 Reply Last reply Reply Quote 0
                                  • mesacrashundefined
                                    mesacrash @droftarts
                                    last edited by

                                    @droftarts I don't see the configuration tool, wth?

                                    droftartsundefined 1 Reply Last reply Reply Quote 0
                                    • droftartsundefined
                                      droftarts administrators @mesacrash
                                      last edited by

                                      @mesacrash https://configtool.reprapfirmware.org/Start

                                      Cartesian bed-slinger with Duet 3 Mini 5+ WiFi and 1LC : RRP Fisher Delta v1 with Duet 2 Maestro : TronXY X5S with Duet 3 MB6HC and Roto toolboard

                                      1 Reply Last reply Reply Quote 0
                                      • First post
                                        Last post
                                      Unless otherwise noted, all forum content is licensed under CC-BY-SA