Control for “Maslow” style cnc

o_lampe

@CNCModeller said in Control for “Maslow” style cnc:

a large plotter to mark out the cuts

That'll be much more accurate I guess, but the pen would need a bit of downforce to write. Maybe a small vacuum hose on the effector? Or an airbrush instead of a pen? That way you can also put your Logo on the crates or a "Fragile" sign...
A diode laser would probably work too, but the lines would be very fine.

droftarts

@CNCModeller said in Control for “Maslow” style cnc:

I could just use a large plotter

Something like the open source Makelangelo would work: https://www.marginallyclever.com/products/makelangelo-5-huge/
It runs on Marlin, so I'd think it would be transportable to Duet: https://www.marginallyclever.com/2021/10/friday-facts-4-how-to-marlin-polargraph/
A very old blog post about the kinematics https://www.marginallyclever.com/2012/02/drawbot-overview/
His software looks pretty fully-featured for making wall art, too.

Alternatively https://www.instructables.com/Polargraph-Wall-Draw-Bot-2023/ has a link to GRBL-Polargraph fork.

I'm pretty keen to make one of these, too, in case you hadn't realised... Somehow just need to find the time to see if the Hangprinter kinematics will work, or if we need to lift the Polargraph kinematics from Marlin or GRBL.

It would be cool to mount a low power diode laser on something like this to cut custom cardboard packaging, too.

Ian

o_lampe

@droftarts I started building a test-rig, but without steppers. Just to proove my belt-length correction theory. It's still a lot to compensate, I think I might use a torque-mode BLDC instead of the weight. (simpleFOC driven, since it can be completely independent from RRF)

PS: The effector was the first thing I found when looking for a triangle shaped thing. I might make a supercheap sandtable instead.

droftarts

@o_lampe Nice. Did it work?! I think what you have nearly made is a CoreXY! The nice thing about the Polarbots is that they only need two pivot points, at the motor. Yours needs a full frame, so it may as well be a CoreXY, perhaps more like https://corexy.com/botofthecloth/index.html

What I've noticed from most of the polarbots I've looked at is that there is a linkage for each belt around the centre of the effector, so that it's always a straight line between motor and 'pen' (or spindle). The Makelangelo and Maslow does this, in different ways. More complicated physically, but less computation within the kinematics.

Ian

o_lampe

@droftarts Opposite to a CoreXY I don't need linear guides or a crossbeam. The motion is similar, but there's no linear correlation between A+B motors.
Until the weekend I'll have a stepper driven rig. Then I can post a video.

droftarts

@o_lampe I just realised the Maslow4 is quite different. The Maslow 1 and 2 (no idea what happened to Maslow 3) were polarbots, with a belt/chain from each top corner, but the Maslow 4 is more like a 2D quad-tower delta, and probably much closer to Hangprinter than previous versions. Again, the Hangprinter kinematics might do this, too.

Ian

o_lampe

@droftarts Maybe the Maslow_3 was a flop and that's why they again had to kickstart their next project? They even pulled the "Ukraine" card to gain more money.
IMHO the Maslow_4 isn't a good design, using brushed DC motors and expensive ODrive controllers.

there is a linkage for each belt around the centre of the effector, so that it's always a straight line between motor and 'pen'
I think I figured out how to trick RRF to do the correct calculations without rotating belt links. It's similar to Delta-kinematics, where we have to measure rod length and horizontal distance between towers and effector.
I just have to measure the horizontal distance from motorshaft (minus pulley radius) to the fixed link on the effector. Will add it in my next picture for reference.

PS: I like the BotofTheCloth idea with it's strap-on corners. For a plotter or laser it might be good enough: Just buy a 8' x 6' plywood sheet and clamp the motors and idlers directly. No need for a permanent frame which only occupies workspace 99% of the time.

CNCModeller

@o_lampe said in Control for “Maslow” style cnc:

PS: I like the BotofTheCloth idea with its strap-on corners. For a plotter or laser it might be good enough: Just buy a 8' x 6' plywood sheet and clamp the motors and idlers directly. No need for a permanent frame which only occupies workspace 99% of the time.

I had exactly the sam thought, personally the idea of having all of the moving parts in the plotter carriage with just a fixed anchor point at the corner of the 8x6 sheet would be ideal. Literally just put a screw in each corner and attach the belts, calibrate, and you’re r away. Ideally everything would retract into the plotter carriage for storage.

I also like the idea of a diode laser to mark out for manual cuts and labelling.

I could even see a larger version being used to layout where you put holes for steelwork or walls etc on a building concrete slab during construction.

All interesting stuff…

o_lampe

I added steppers and a central tightening winch. The idea of the hidden weight is not too good, because it would almost move the same as if it was connected directly to the effector.
This way it won't work with the strap-on corner idea, unless you are willing to drill 3 holes in the 8x6 everytime.

o_lampe

I tried my luck and modified config for a 2D hangprinter.
It seems RRF3.4.6 already has the latest version of HP-kinematics. It is oddly specific regarding spool diameter and all.

m98 p"config.g"
Error: Wrong number of values after '''D''', expected 3
Q:Buildup fac 0.0070
R:Spool r 75.00, 75.00, 75.00, 75.00
U:Mech Adv 2, 2, 2, 4
O:Lines/spool 1, 1, 1, 1
L:Motor gear teeth 20, 20, 20, 20
H:Spool gear teeth 255, 255, 255, 255
J:Full steps/rev 25, 25, 25, 25
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled

droftarts

@o_lampe What are the commands you are using to define it? I'd imagine that the C and D motors don't really matter in M669. Are the other values set in firmware? That might rather limit the usefulness of the Hangprinter kinematics.

Ian

o_lampe

@droftarts I figured, I could use any two of the ABC motor to define a 2D plane. So I took the BC motors, because they already defined the left and right corner. (A motor is the front/center motor)
Here's the basic config.g, but I don't know how to match XY with ABCD or how to define a tool for a plotter

; Configuration file for Duet WiFi (firmware version 3)
;
; General preferences
G90                                                    ; send absolute coordinates...
M83                                                    ; ...but relative extruder moves
M550 P"Hangprinter_2D"                                     ; set printer name

M669 K6 A0.0:220.0:0.0 B-220.0:220.0:0.0 C220.0:220.0:0.0 D2000.0 P100.0 Q0.0 R1 


M666 X0 Y0 Z0                                          ; put your endstop adjustments here, or let auto calibration find them

; Network
M552 S1                                                ; enable network
M586 P0 S1                                             ; enable HTTP
M586 P1 S0                                             ; disable FTP
M586 P2 S0                                             ; disable Telnet

; Drives
M569 P0 S0                                             ; physical drive 0 goes forwards
M569 P1 S0                                             ; physical drive 1 goes forwards
M569 P2 S0                                             ; physical drive 2 goes forwards
M569 P3 S0                                             ; physical drive 3 goes forwards

M584 A0 B1 C2 D3                                             ; set drive mapping 
M350 A16 B16 C16 D16 I1                                ; configure microstepping with interpolation
M92 A200.00 B200.00 C200.00 D0                       ; set steps per mm
M566 A900.00 B900.00 C900.00 D1200              ; set maximum instantaneous speed changes (mm/min)
M203 A24000.00 B24000.00 C24000.00 D4800            ; set maximum speeds (mm/min)
M201 A4000.00 B4000.00 C4000.00 D1000               ; set accelerations (mm/s^2)
M906 A200 B400 C400 D200 I70                        ; set motor currents (mA) and motor idle factor in per cent

M84 S10                                                ; Set idle timeout


; Axis Limits
M208 X-100:100 Y-100:100 Z0:10


; Tools
M563 P0                                           ; define tool 0
G10 P0 X0 Y0 Z0                                       ; set tool 0 axis offsets


M911 S20 R22 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"     ; set voltage thresholds and actions to run on power loss
T0                                                     ; select first tool

//edit OK, I guess I found the reason for one of the errormessages: "D" on has one parameter in my config, but needs three....
YES, that solved most of it, although I still don't know, if I have to map AB drives to XY axes? I guess it should be done automatically by the kinematic model?

droftarts

@o_lampe Looks like our Hangprinter documentation needs updating; there's a whole bunch of parameters not covered on the wiki page here https://docs.duet3d.com/User_manual/Machine_configuration/Configuration_Hangprinter
Looks like you can define Q, R, U, O, L, H and J: https://github.com/Duet3D/RepRapFirmware/blob/47435151e110f373fc80721a2c265e38b8ec5e3b/src/Movement/Kinematics/HangprinterKinematics.cpp#L203
So it's coming up with sensible numbers for those as well, I guess. There's a reasonable amount of comments in HangprinterKinematics.cpp to hopefully work out what is going on!

Ian

droftarts

@o_lampe Also note that, as of RRF 3.5.0-beta4, Hangprinter support is removed from Duet 2 WiFi/Ethernet builds. RRF 3.4.6 is fine, though. Just in case you decide to update!
https://github.com/Duet3D/RepRapFirmware/wiki/Changelog-RRF-3.x-Beta#reprapfirmware-350-beta4

[Duet 2] Hangprinter kinematics are no longer supported in the standard build of Duet2CombinedFirmware because of lack of flash memory space

Ian

o_lampe

@droftarts I have made some progress and got motion in the right directions. But tightening the belts and adding some gravity needs a propper balance of forces. I played with the L&H values and Q&R as well, but didn't see a difference.

@CNCModeller How about window cleaning on skyscrapers? The strap-on corners will fit almost anywhere.

o_lampe

I played a bit more with the HP-kinematics, but there are some weird things I couldn't work out yet:

No matter what I set as steps/mm, it always moves 1/3 of the requested length (XYZABCD, tried all)
I can't move past X0. Positive X-moves are straight, but lower than X0, it starts to make a curve
although I only have ABCD axes in the kinematic model, I have to set motor currents for XYZ??

Not very promissing.
I really don't want to dig out an old RAMPS controller and bite my teeth out, configuring Marlin

o_lampe

I found the inverse kinematics which are pretty simple.
Just don't want to fall in this rabbit hole called "RRF compiling...with Eclipse"

; inverse kinematics of Makelangelo polargraph plotter

function IK(P) {
  A = Px - M1x;  
  B = Py - M1y;  
  M1P = square_root(A*A+B*B);
  A = Px - M2x;  
  // B is the same
  M2P = square_root(A*A+B*B);

  return M1P,M2P;
}

o_lampe

I completely missed that M666 alters the Q,R,L,H,J... settings. Now I've set them to my best knowledge, ~~but now the steppers don't energize.~~
I had to set a Q-value greater 0 to make it work.
The XY axes both work in the right direction, but they aren't perpendicular to each other.

m669
Kinematics is Hangprinter, 100 segments/sec, min. segment length 0.20mm
A:0.00, -200.00, 0.00
B:193.00, 241.00, 0.00
C:-193.00, 241.00, 0.00
D:0.00, 0.00, 200.00
P:Print radius: 200.0

m666
Q:Buildup fac 0.0000
R:Spool r 6.00, 6.00, 6.00, 6.00
U:Mech Adv 1, 1, 1, 1
O:Lines/spool 1, 1, 1, 1
L:Motor gear teeth 20, 20, 20, 20
H:Spool gear teeth 20, 20, 20, 20
J:Full steps/rev 200, 200, 200, 200

droftarts

@o_lampe I'm not sure where you are up to on your project, but a couple of notes might help from my Polargraph.

although I only have ABCD axes in the kinematic model, I have to set motor currents for XYZ??

In the config.g you posted earlier (which you may already have changed), you have defined the ABCD axes in M584. However, Hangprinter maps the ABCD drives to XYZU. Because ABCD are really anchor points, rather than motor axes. All speeds, accelerations, motor currents etc are in terms of XYZU. See https://docs.duet3d.com/User_manual/Machine_configuration/Configuration_Hangprinter#select-hangprinter-kinematics

I can't move past X0. Positive X-moves are straight, but lower than X0, it starts to make a curve

I had this too. It was caused by the motor assignments, and I actually had the motors mapped incorrectly. Because you only want to use the B and C anchor points, you only use the Y and Z motor assignments. For a long time I was using X and Y! Made particularly confusing for me, because I have the Z motor driver for the Y axis, and E1 motor driver for Z axis. If only we had just called them driver 0 to 4! See the config.g in the Polargraph thread: https://forum.duet3d.com/topic/35248/duet-polargraph

I think you resolved the M666 problems, and I think mine are set similar to yours. As far as I can tell, it's mostly to do with gearing and spool wind up, so largely irrelevant for our application, just have to set sensible numbers.

Ian