3.5.0b4 losing XYZ position after print completes?

Phaedrux

Can you post your config,g as well?

What is the idle current for the motors set to?

droftarts

@paralepsis said in 3.5.0b4 losing XYZ position after print completes?:

G91 ; relative movement
G1 Z50 F5000 ; lift nozzle 50mm
G90 ; absolute movement
G1 X20 Y250 ; go to back left

You have quite a big Z and Y relative move at the end of the print. Could it be that this is beyond the limits of the machine, or something else stops it moving and causes Y and Z to skip at the end of the print? if you take the last few lines of the Gcode file, so you know the position of the axes at the end of the print, and run the above commands, what happens?

Also, the M204 command M204 S10000 is incorrect. RRF does not support an S parameter. See https://docs.duet3d.com/en/User_manual/Reference/Gcodes#m204-set-printing-and-travel-accelerations

Ian

paralepsis

@Phaedrux sure.

; RailCore RRF standalone for Duet3
; From: https://github.com/railcore/configs
;
G21						;Work in millimetres
G90						;Send absolute coordinates...
M83						;...but relative extruder moves

; Stepper configuration
;  https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareCoreXYPrinter
;
;  M569 P0 S0 ; X motor runs forwards -- +X+Y
;  M569 P1 S0 ; Y motor runs forwards -- +X-Y
;  Switch S parameter 0->1 or 1->0 if carriage moves the wrong way.
;
; Filastruder kit is LDO 0.9 degree steppers for X,Y, Z and Extruder
; 
M569 P0 S1 D3					;Drive 0 X / Rear
M569 P1 S0 D3					;Drive 1 Y / Front
M569 P2 S1 D3					;Drive 2 Z Front Left
M569 P3 S1 D3					;Drive 3 Z Rear Left
M569 P4 S1 D3					;Drive 4 Z Right
M569 P5 S1 D3					;Drive 5 Extruder

; Axis configuration
;
M669 K1							;corexy mode
M584 X0 Y1 Z2:3:4 E5			; Map X to drive 0 Y to drive 1, Z to drives 2, 3, 4, and E to drive 5

;Leadscrew locations
M671 X-10:-10:333  Y22.5:277.5:150 S7.5

M350 X16 Y16 Z16 E16 I1			;set 16x microstepping for axes with interpolation
M906 X1400 Y1400 Z1200 E800 I80	;Set motor currents (mA)
M201 X2500 Y2500 Z100 E1500		;Accelerations (mm/s^2)
M203 X24000 Y24000 Z900 E3600	;Maximum speeds (mm/min) 
M566 X800 Y800 Z100 E1500		;Maximum jerk speeds mm/minute 
M208 X295 Y303 Z290				;set axis maxima and high homing switch positions (adjust to suit your machine)
M208 X-11 Y0 Z0 S1				;set axis minima and low homing switch positions (adjust to make X=0 and Y=0 the edges of the bed)
M92 X200 Y200 Z1600 E830		;steps/mm (E830 - 415x2 b/c 0.9 degree motor!)

; Stall Detection (Testing)
; 
; Note: S value controls sensitivity, lower is more sensitive.
M915 X Y R2 F1 S9 H400

; End Stops
M574 X1 S1 P"io1.in"			;Map the X endstop to io1.in
M574 Y1 S1 P"io2.in"			;May the Y endstop to io2.in
 
; Thermistors
M308 S0 P"temp0" Y"thermistor" A"bed_heat" T100000 B4240 H0 L0 		;Bed thermistor - connected to temp0
M308 S1 P"temp1" Y"thermistor" A"e0_heat" T100000 B4725 C7.06e-8 H0 L0	;duet3 e3d thermistor - connected to e0_heat
M308 S3 P"temp3" Y"thermistor" A"bed_heat2" T100000 B3950 H0 L0      ; Bed thermistor - Keenevo builtin

; MCU Temp and TMC drivers -- need this before we set up the fan
M308 S10 Y"mcu-temp" A"MCUTemp[C]"
M308 S11 Y"drivers" A"TMC[Warning]"

; DHT22
M308 S12 P"io8.out" Y"dht22" A"Chamber Temp[C]"
M308 S13 P"S12.1" Y"dhthumidity" A"Chamber Humid[%]"

;Define Heaters
M950 H0 C"out0" T0				;Bed heater is on out0
M950 H1 C"out1" T1				;Hotend heater is on out1

;Define Bed
M140 H0

; Tuning Heaters
;   https://docs.duet3d.com/en/How_to_guides/Commissioning
;
; M307 H0 B0 R0.237 C862.8 D27.12 S1.00 V23.8 ; Keenovo, 6/26/2022, Duet Firmware 3.3
M307 H0 B0 R0.254 K0.102:0.000 D27.86 E1.35 S0.90 ; Keenovo 6/11/2023, Duet FW 3.4.5, 90% power
M307 H1 B0 R2.850 C198.6:142.2 D5.59 S1.00 V23.8 ; Mosquito @ 260C, 7/16/2022, Duet  Firmware 3.3

M570 S360					;Hot end may be a little slow to heat up so allow it 180 seconds
M143 H1 S285				;Set max hotend temperature
M143 H0 A2 S130 T3 C0		; Temporarily turn off bed heater when Keenovo sensor says 130C+

; Fans
; Note: Making part fan Fan 0 b/c slicers sort of expect it. -- RBR
; 
M950 F1 C"out5"					;Hotend fan on "out5" connector
M106 P1 S255 H1 T50 C"HotEndFan";enable thermostatic mode for hotend fan
M950 F0 C"out4"					;Layer fan on "out4" connector
M106 P0 S0						;Layer Fan
M950 F2 C"out6"					;Electronics fan on "out6" connector
M106 P2 S0 C"ElectFan"			;Electronics Fan
M950 F3 C"out9"                 ;Chamber fan on "out9" connector
M106 P3 S0 C"ChamberFan"        ;Chamber Fan

; Tool definitions
M563 P0 D0 H1 F0                      		;Define tool 0 (Fan 0 is Fan 0 :))
G10 P0 S0 R0                        		;Set tool 0 operating and standby temperatures

; BLTouch
; Note: This puts the nozzle about 0.05mm off the plate @ Z=0
;
M558 P9 C"io7.in" H5 R1 F120 T6000 A5 S0.02 B1	;define the bltouch input on io7.in
M950 S0 C"io7.out"				;define the bltouch servo on io7.out
; G31 X-2 Y37 Z0.8 P25 			;set the offsets for the bltouch -- E3D mount
G31 X-2 Y37 Z2.05 P25 			;set the offsets for the bltouch -- direct mount

; Ethernet network
M552 P192.168.1.14 S1
M550 P"Beast"

; BTT Smart Filament Sensor
M591 D0 P7 C"io6.in" L7 R50:150 E22 S1

; PanelDue on "out0" connector
M575 P1 S1 B57600

T0						;select first hot end

paralepsis

@droftarts thanks for the catch on M204; I'll have to fix that.

No, I don't think I'm exceeding the capabilities of the machine with those last commands -- the movement/acceleration/jerk settings that are in my config.g are considered conservative for this design. Also, this wasn't happening with 3.4.5 for many many prints.

I've had this happen once more since posting, have started just homing Z so I don't have to think about it (which obviously isn't treating the condition...).

paralepsis

@paralepsis The XYZ motors are LDO-42STH40-1684MAC (https://cdn.shopify.com/s/files/1/0239/9287/files/LDO-42STH38-1684MAC_TIM_RevA.pdf).

paralepsis

To follow up on this, an F5000 Z move would indeed be a problem if the speed weren't capped by the config.g settings, but it is :). I'll clean that up in the stop.g anyway, just so it isn't a distraction in the future.

Thanks again!

droftarts

@paralepsis said in 3.5.0b4 losing XYZ position after print completes?:

No, I don't think I'm exceeding the capabilities of the machine with those last commands -- the movement/acceleration/jerk settings that are in my config.g are considered conservative for this design.

I was thinking more of the physical limits of the print bed, rather than skipping steps.

Ian

paralepsis

@droftarts maybe I misunderstand, but the X/Y move isn't relative, just moves to near the back left corner (xmin is -11 and ymax is 300ish). Notionally the Z could push to Z-max, but the prints in question have been in the ~100mm or less height, and I've got roughly 280-300mm of Z to work with.

gloomyandy

@paralepsis Does your printer have more than one tool? You have T99 in your stop.g, I'm not sure what it is you are trying to do with that, but I wonder if in effect causing a tool change is part of the problem?

paralepsis

@gloomyandy I don't have more than one tool. I was using that as a way to kick the current tool out of active mode...I want to say that M568 wasn't around when I first started doing that, but it's also possible I just didn't find it.

Either way, that would be a regression -- I've been doing that "tool switch" trick on this machine and one other for years w/out issue prior to move to 3.5.0b4.

jay_s_uk

@paralepsis you should use T-1 to unmount the current tool

paralepsis

@jay_s_uk I feel like I got an error trying to do that (way back when), but really M568 P0 A0 is probably the right thing in a single tool printer, yes?

jay_s_uk

@paralepsis to turn it off, yes, thats what i use