3.5.0-B3 Reboot in Laser mode

jay_s_uk

@cichaczech post an output of M122 after the reboot

cichaczech

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.5.0-beta.3 (2023-04-14 11:27:37) running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9P6M2-NW4SS-6JKDD-3S86R-KAZ7L
Used output buffers: 1 of 26 (15 max)
=== RTOS ===
Static ram: 22192
Dynamic ram: 74716 of which 244 recycled
Never used RAM 15992, free system stack 184 words
Tasks: NETWORK(nWait,11.0%,238) HEAT(nWait,0.0%,386) Move(nWait,0.0%,364) MAIN(running,80.9%,559) IDLE(ready,8.1%,29), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:00:11 ago, cause: software
Last software reset at 2023-06-09 12:21, reason: HardFault bfarValid precise, Gcodes spinning, available RAM 15492, slot 2
Software reset code 0x4063 HFSR 0x40000000 CFSR 0x00008200 ICSR 0x0041f803 BFAR 0x6b4bd9b0 SP 0x20003b38 Task Move Freestk 379 ok
Stack: 20008908 00000001 00000270 6b4bd450 a5a5a5a5 0042a6e3 0043cee0 a1000000 00000000 00000000 00000000 00000000 3f800000 00000000 00000000 00000000 2000bcf8 00000000 00000001 2000bcfc 2000487c 00000000 00000000 a5a5a5a5 0042a6e3 a5a5a5a5 a5a5a5a5
Error status: 0x00
Aux0 errors 0,0,19
MCU temperature: min 23.8, current 24.1, max 24.4
Supply voltage: min 23.6, current 23.7, max 23.8, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min n/a
Driver 1: standstill, SG min n/a
Driver 2: standstill, SG min n/a
Driver 3: standstill, SG min n/a
Driver 4: standstill, SG min n/a
Driver 5: 
Driver 6: 
Driver 7: 
Driver 8: 
Driver 9: 
Driver 10: 
Driver 11: 
Date/time: 2023-06-09 12:21:49
Cache data hit count 418033720
Slowest loop: 8.31ms; fastest: 0.19ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 12.0MBytes/sec
SD card longest read time 1.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
no step interrupt scheduled
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Movement locks held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is assembling a command in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Q0 segments left 0
Code queue 0 is empty
=== Filament sensors ===
Extruder 0 sensor: ok
=== Network ===
Slowest loop: 111.47ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 1 of 8
= WiFi =
Network state is active
Module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
Firmware version 1.27
MAC address bc:ff:4d:45:e0:c1
Module reset reason: Power up, Vcc 3.39, flash size 4194304, free heap 27176
WiFi IP address 10.0.0.120
Signal strength -59dBm, channel 0, mode 802.11n, reconnections 0
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0

dc42

@cichaczech as we're in the process of releasing 3.5.0-beta4 please can you test it again using that release and report back. If it happens in beta4 then please post a M122 report after the reset again.

cichaczech

@dc42 Ok, will do.
Thank you.

cichaczech

@dc42 still the same

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.5.0-beta.4 (2023-06-08 23:39:39) running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9P6M2-NW4SS-6JKDD-3S86R-KAZ7L
Used output buffers: 1 of 26 (15 max)
=== RTOS ===
Static ram: 23236
Dynamic ram: 74836 of which 244 recycled
Never used RAM 14828, free system stack 184 words
Tasks: NETWORK(2,nWait,12.2%,238) HEAT(3,nWait,0.0%,385) Move(4,nWait,0.0%,364) MAIN(1,running,81.7%,819) IDLE(0,ready,6.1%,29), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:00:15 ago, cause: software
Last software reset at 2023-06-09 17:27, reason: HardFault bfarValid precise, Gcodes spinning, available RAM 14328, slot 0
Software reset code 0x4063 HFSR 0x40000000 CFSR 0x00008200 ICSR 0x0041f803 BFAR 0x6b4bddd0 SP 0x20003f60 Task Move Freestk 379 ok
Stack: 20008d28 00000001 00000270 6b4bd870 a5a5a5a5 004291c3 0043c218 a1000000 00000000 00000000 00000000 00000000 3f800000 00000000 00000000 00000000 2000c168 00000000 00000001 2000c16c 20004bb4 00000000 00000000 a5a5a5a5 004291c3 a5a5a5a5 a5a5a5a5
Error status: 0x00
Aux0 errors 0,0,18
MCU temperature: min 22.9, current 23.5, max 23.6
Supply voltage: min 23.6, current 23.7, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min n/a
Driver 1: standstill, SG min n/a
Driver 2: standstill, SG min n/a
Driver 3: standstill, SG min n/a
Driver 4: standstill, SG min n/a
Driver 5: 
Driver 6: 
Driver 7: 
Driver 8: 
Driver 9: 
Driver 10: 
Driver 11: 
Date/time: 2023-06-09 17:28:13
Cache data hit count 558914657
Slowest loop: 8.27ms; fastest: 0.19ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 12.0MBytes/sec
SD card longest read time 1.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, height map offset 0.000, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Movement locks held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is assembling a command in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Q0 segments left 0
Code queue 0 is empty
=== Filament sensors ===
Extruder 0 sensor: ok
=== Network ===
Slowest loop: 111.94ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 1 of 8
= WiFi =
Interface state: active
Module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
Firmware version 1.27
MAC address bc:ff:4d:45:e0:c1
Module reset reason: Power up, Vcc 3.39, flash size 4194304, free heap 27096
WiFi IP address 10.0.0.120
Signal strength -59dBm, channel 0, mode 802.11n, reconnections 0
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0

dc42

@cichaczech please try again. The stack trace in your M122 report doesn't match the 3.4.0-beta.4 code, so I suspect you were running different firmware when that last reset happened.

cichaczech

@dc42 Today I tried delete old FW and instal beta4 with BOSSA, but it still keeps rebooting when I try to home it.
For now I am moving back to last stable release

this is my latest M122

=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.5.0-beta.4 (2023-06-08 23:39:39) running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9P6M2-NW4SS-6JKDD-3S86R-KAZ7L
Used output buffers: 13 of 26 (20 max)
=== RTOS ===
Static ram: 23236
Dynamic ram: 74836 of which 244 recycled
Never used RAM 14828, free system stack 186 words
Tasks: NETWORK(2,nWait,12.5%,238) HEAT(3,nWait,0.0%,383) Move(4,nWait,0.0%,364) MAIN(1,running,78.8%,819) IDLE(0,ready,8.7%,29), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:00:10 ago, cause: software
Last software reset at 2023-06-12 09:11, reason: HardFault bfarValid precise, Gcodes spinning, available RAM 14328, slot 2
Software reset code 0x4063 HFSR 0x40000000 CFSR 0x00008200 ICSR 0x0041f803 BFAR 0x6b4bddd0 SP 0x20003f60 Task Move Freestk 379 ok
Stack: 20008d28 00000001 00000270 6b4bd870 a5a5a5a5 004291c3 0043c218 a1000000 00000000 00000000 00000000 00000000 3f800000 00000000 00000000 00000000 2000c168 00000000 00000001 2000c16c 20004bb4 00000000 00000000 a5a5a5a5 004291c3 a5a5a5a5 a5a5a5a5
Error status: 0x00
Aux0 errors 0,0,18
MCU temperature: min 22.2, current 22.7, max 23.0
Supply voltage: min 23.7, current 23.7, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min n/a
Driver 1: standstill, SG min n/a
Driver 2: standstill, SG min n/a
Driver 3: standstill, SG min n/a
Driver 4: standstill, SG min n/a
Driver 5: 
Driver 6: 
Driver 7: 
Driver 8: 
Driver 9: 
Driver 10: 
Driver 11: 
Date/time: 2023-06-12 09:11:56
Cache data hit count 397729243
Slowest loop: 9.39ms; fastest: 0.19ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 12.0MBytes/sec
SD card longest read time 1.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, height map offset 0.000, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Movement locks held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is assembling a command in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Q0 segments left 0
Code queue 0 is empty
=== Filament sensors ===
Extruder 0 sensor: ok
=== Network ===
Slowest loop: 114.56ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(2) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 3 of 8
= WiFi =
Interface state: active
Module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
Firmware version 2.1beta3
MAC address bc:ff:4d:45:e0:c1
Module reset reason: Power up, Vcc 3.38, flash size 2097152, free heap 38084
WiFi IP address 10.0.0.120
Signal strength -54dBm, channel 1, mode 802.11n, reconnections 0
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0

dc42

@cichaczech please can you provide your config.g and homing files, so that I can try to reproduce this.

dc42

@cichaczech I haven't managed to reproduce the problem, but I believe I have identified the issue. It's specific to laser mode. Please try the Duet 2 firmware binary at https://www.dropbox.com/sh/c4aatfdsejjjab0/AACGuZ4qUBvZz49zxErkhmnWa?dl=0 and see if it resolves the problem.

I think a workaround for this issue using the original 3.5.0-beta4 firmware binary would be to issue a G1 move with an S parameter after switching to laser mode with M452 but before doing the very first real move (i.e. before homing). Even G1 S0 with no other parameters should be sufficient.

cichaczech

@dc42 Both of your solutions work.

3.5.0-beta4 -> you have to send G1 S0 after switching laser mode
3.5.0-beta4+ -> works normally in laser mode, without any additional commands

Thank you.

dc42

@cichaczech thanks for confirmation! The fix will be included in 3.5.0-rc.1. I'll mark the Github issue I created at https://github.com/Duet3D/RepRapFirmware/issues/869 solved.

dc42 created this issue in Duet3D/RepRapFirmware

3.5.0-B3 Reboot in Laser mode

closed [3.5beta3, beta4] Unexpected reset when using laser mode #869