Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    npn 5v fly rrf e3

    Scheduled Pinned Locked Moved
    STM
    3
    35
    1.5k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • gloomyandyundefined
      gloomyandy @npm1
      last edited by

      @npm1 and the results with the Z driver removed from the socket?

      npm1undefined 1 Reply Last reply Reply Quote 0
      • npm1undefined
        npm1 @gloomyandy
        last edited by

        @gloomyandy

        removed z driver with m574
        g31
        Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
        2/25/2022, 8:59:47 PM M119
        Endstops - X: not stopped, Y: at min stop, Z: not stopped, Z probe: not stopped
        2/25/2022, 8:59:44 PM M119
        2/25/2022, 8:59:33 PM M98 P"config.g"
        HTTP is enabled on port 80
        FTP is disabled
        TELNET is disabled

        Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

        npm1undefined 1 Reply Last reply Reply Quote 0
        • npm1undefined
          npm1 @npm1
          last edited by

          @gloomyandy removed z driver with m574 metal touching

          g31
          Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
          2/25/2022, 9:01:46 PM g31
          2/25/2022, 9:01:24 PM M119
          Endstops - X: not stopped, Y: at min stop, Z: not stopped, Z probe: not stopped

          Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

          npm1undefined gloomyandyundefined 2 Replies Last reply Reply Quote 0
          • npm1undefined
            npm1 @npm1
            last edited by

            @gloomyandy removed z driver without m574

            g31

            Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
            2/25/2022, 9:04:04 PM g31
            2/25/2022, 9:03:53 PM M119
            Endstops - X: not stopped, Y: at min stop, Z: no endstop, Z probe: not stopped

            Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

            npm1undefined 1 Reply Last reply Reply Quote 0
            • npm1undefined
              npm1 @npm1
              last edited by

              @gloomyandy removed z driver without m574 metal touching

              G31

              Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
              2/25/2022, 9:05:35 PM m119
              Endstops - X: not stopped, Y: at min stop, Z: no endstop, Z probe: not stopped

              Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

              npm1undefined 1 Reply Last reply Reply Quote 0
              • npm1undefined
                npm1 @npm1
                last edited by

                hope that helps

                Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                1 Reply Last reply Reply Quote 0
                • gloomyandyundefined
                  gloomyandy @npm1
                  last edited by

                  @npm1 Are you still using this line for your probe definition:

                  M558 P5 C"!^zstop" H5 F120 T6000

                  If so with the Z driver still removed enter

                  M558 P5 C"zstop" H5 F120 T6000

                  in the console (or change the line in your config.g and reboot)
                  and rerun both sets of tests.

                  npm1undefined 1 Reply Last reply Reply Quote 0
                  • npm1undefined
                    npm1 @gloomyandy
                    last edited by

                    @gloomyandy still no changes, the only thing that change is the z probe value being 1000 instead of zero

                    Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                    npm1undefined 1 Reply Last reply Reply Quote 0
                    • npm1undefined
                      npm1 @npm1
                      last edited by

                      @gloomyandy have I blown something on the board

                      Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                      npm1undefined 1 Reply Last reply Reply Quote 0
                      • npm1undefined
                        npm1 @npm1
                        last edited by

                        shall i update the firmware

                        Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                        npm1undefined 1 Reply Last reply Reply Quote 0
                        • npm1undefined
                          npm1 @npm1
                          last edited by

                          Electronics
                          Diagnostics
                          Board: fly_E3 (STMWiFi)
                          Firmware: RepRapFirmware for STM32F4 based Boards 3.3RC2+1_1 (2021-05-13)
                          Duet WiFi Server Version: 1.26-01S-D

                          Note: You can install updates on the System page.

                          Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                          npm1undefined gloomyandyundefined 2 Replies Last reply Reply Quote 0
                          • npm1undefined
                            npm1 @npm1
                            last edited by

                            will marlin be easier

                            Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                            1 Reply Last reply Reply Quote 0
                            • gloomyandyundefined
                              gloomyandy @npm1
                              last edited by gloomyandy

                              @npm1 Can you turn off your board, disconnect the probe and plug in one of the other endstop switches (x or y) into the zstop socket. Then run the two tests again once without pressing the endstop switch, then again with the endstop switch pressed. Run this test with the Z driver still removed.

                              npm1undefined 1 Reply Last reply Reply Quote 0
                              • npm1undefined
                                npm1 @gloomyandy
                                last edited by

                                @gloomyandy endstop works with zero issues with everything triggered correctly

                                M119

                                Endstops - X: at min stop, Y: at min stop, Z: at min stop, Z probe: at min stop
                                2/25/2022, 9:38:20 PM g31
                                Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
                                2/25/2022, 9:38:10 PM m119
                                Endstops - X: at min stop, Y: at min stop, Z: not stopped, Z probe: not stopped

                                Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                                npm1undefined 1 Reply Last reply Reply Quote 0
                                • npm1undefined
                                  npm1 @npm1
                                  last edited by

                                  @gloomyandy the only thing i can think of is to switch the cables on the zstop cables around

                                  Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                                  gloomyandyundefined 1 Reply Last reply Reply Quote 0
                                  • gloomyandyundefined
                                    gloomyandy @npm1
                                    last edited by

                                    @npm1 @npm1 In which case I would be looking very closely at that probe. Are you sure you have correctly identified the various wires? See: https://forum.duet3d.com/topic/25906/inductive-sensor-npn-no-not-working?_=1645824856161 (thanks to Jay for digging that one out).

                                    npm1undefined 1 Reply Last reply Reply Quote 0
                                    • npm1undefined
                                      npm1 @gloomyandy
                                      last edited by

                                      @gloomyandy i knoq that the 5v cable is correctly connected ill switch the cables around and confirm to you shortly

                                      Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                                      npm1undefined 1 Reply Last reply Reply Quote 0
                                      • npm1undefined
                                        npm1 @npm1
                                        last edited by

                                        I'm just gonna call it a day, may use an optical setup it with one of those allen keys

                                        Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                                        npm1undefined 1 Reply Last reply Reply Quote 0
                                        • npm1undefined
                                          npm1 @npm1
                                          last edited by

                                          thanks for your efforts

                                          Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                                          1 Reply Last reply Reply Quote 0
                                          • First post
                                            Last post
                                          Unless otherwise noted, all forum content is licensed under CC-BY-SA