Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    npn 5v fly rrf e3

    STM
    3
    35
    1.3k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • npm1undefined
      npm1 @npm1
      last edited by

      @gloomyandy have I blown something on the board

      Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

      npm1undefined 1 Reply Last reply Reply Quote 0
      • npm1undefined
        npm1 @npm1
        last edited by

        shall i update the firmware

        Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

        npm1undefined 1 Reply Last reply Reply Quote 0
        • npm1undefined
          npm1 @npm1
          last edited by

          Electronics
          Diagnostics
          Board: fly_E3 (STMWiFi)
          Firmware: RepRapFirmware for STM32F4 based Boards 3.3RC2+1_1 (2021-05-13)
          Duet WiFi Server Version: 1.26-01S-D

          Note: You can install updates on the System page.

          Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

          npm1undefined gloomyandyundefined 2 Replies Last reply Reply Quote 0
          • npm1undefined
            npm1 @npm1
            last edited by

            will marlin be easier

            Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

            1 Reply Last reply Reply Quote 0
            • gloomyandyundefined
              gloomyandy @npm1
              last edited by gloomyandy

              @npm1 Can you turn off your board, disconnect the probe and plug in one of the other endstop switches (x or y) into the zstop socket. Then run the two tests again once without pressing the endstop switch, then again with the endstop switch pressed. Run this test with the Z driver still removed.

              npm1undefined 1 Reply Last reply Reply Quote 0
              • npm1undefined
                npm1 @gloomyandy
                last edited by

                @gloomyandy endstop works with zero issues with everything triggered correctly

                M119

                Endstops - X: at min stop, Y: at min stop, Z: at min stop, Z probe: at min stop
                2/25/2022, 9:38:20 PM g31
                Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
                2/25/2022, 9:38:10 PM m119
                Endstops - X: at min stop, Y: at min stop, Z: not stopped, Z probe: not stopped

                Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                npm1undefined 1 Reply Last reply Reply Quote 0
                • npm1undefined
                  npm1 @npm1
                  last edited by

                  @gloomyandy the only thing i can think of is to switch the cables on the zstop cables around

                  Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                  gloomyandyundefined 1 Reply Last reply Reply Quote 0
                  • gloomyandyundefined
                    gloomyandy @npm1
                    last edited by

                    @npm1 @npm1 In which case I would be looking very closely at that probe. Are you sure you have correctly identified the various wires? See: https://forum.duet3d.com/topic/25906/inductive-sensor-npn-no-not-working?_=1645824856161 (thanks to Jay for digging that one out).

                    npm1undefined 1 Reply Last reply Reply Quote 0
                    • npm1undefined
                      npm1 @gloomyandy
                      last edited by

                      @gloomyandy i knoq that the 5v cable is correctly connected ill switch the cables around and confirm to you shortly

                      Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                      npm1undefined 1 Reply Last reply Reply Quote 0
                      • npm1undefined
                        npm1 @npm1
                        last edited by

                        I'm just gonna call it a day, may use an optical setup it with one of those allen keys

                        Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                        npm1undefined 1 Reply Last reply Reply Quote 0
                        • npm1undefined
                          npm1 @npm1
                          last edited by

                          thanks for your efforts

                          Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                          1 Reply Last reply Reply Quote 0
                          • First post
                            Last post
                          Unless otherwise noted, all forum content is licensed under CC-BY-SA