Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    npn 5v fly rrf e3

    Scheduled Pinned Locked Moved
    STM
    3
    35
    1.5k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • gloomyandyundefined
      gloomyandy @npm1
      last edited by

      @npm1 Yes but I asked you to run M119 and G31 twice for each test once without having the probe in a triggered state and then again with the probe in a triggered state (by placing something metal near it so the LED comes on). Have you run the test with the Z driver removed?

      npm1undefined 1 Reply Last reply Reply Quote 0
      • npm1undefined
        npm1 @gloomyandy
        last edited by

        @gloomyandy
        without m574 and with metal touching the probe

        g31

        Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
        2/25/2022, 8:46:38 PM g31
        2/25/2022, 8:46:16 PM M119
        Endstops - X: not stopped, Y: at min stop, Z: no endstop, Z probe: not stopped
        2/25/2022, 8:45:56 PM M98 P"config.g"
        HTTP is enabled on port 80
        FTP is disabled
        TELNET is disabled

        Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

        npm1undefined gloomyandyundefined 2 Replies Last reply Reply Quote 0
        • npm1undefined
          npm1 @npm1
          last edited by

          @gloomyandy with 574 and metal touching probe
          g31
          Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
          2/25/2022, 8:50:23 PM g31
          2/25/2022, 8:50:05 PM m119
          Endstops - X: not stopped, Y: at min stop, Z: not stopped, Z probe: not stopped

          Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

          1 Reply Last reply Reply Quote 0
          • gloomyandyundefined
            gloomyandy @npm1
            last edited by

            @npm1 and the results with the Z driver removed from the socket?

            npm1undefined 1 Reply Last reply Reply Quote 0
            • npm1undefined
              npm1 @gloomyandy
              last edited by

              @gloomyandy

              removed z driver with m574
              g31
              Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
              2/25/2022, 8:59:47 PM M119
              Endstops - X: not stopped, Y: at min stop, Z: not stopped, Z probe: not stopped
              2/25/2022, 8:59:44 PM M119
              2/25/2022, 8:59:33 PM M98 P"config.g"
              HTTP is enabled on port 80
              FTP is disabled
              TELNET is disabled

              Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

              npm1undefined 1 Reply Last reply Reply Quote 0
              • npm1undefined
                npm1 @npm1
                last edited by

                @gloomyandy removed z driver with m574 metal touching

                g31
                Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
                2/25/2022, 9:01:46 PM g31
                2/25/2022, 9:01:24 PM M119
                Endstops - X: not stopped, Y: at min stop, Z: not stopped, Z probe: not stopped

                Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                npm1undefined gloomyandyundefined 2 Replies Last reply Reply Quote 0
                • npm1undefined
                  npm1 @npm1
                  last edited by

                  @gloomyandy removed z driver without m574

                  g31

                  Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
                  2/25/2022, 9:04:04 PM g31
                  2/25/2022, 9:03:53 PM M119
                  Endstops - X: not stopped, Y: at min stop, Z: no endstop, Z probe: not stopped

                  Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                  npm1undefined 1 Reply Last reply Reply Quote 0
                  • npm1undefined
                    npm1 @npm1
                    last edited by

                    @gloomyandy removed z driver without m574 metal touching

                    G31

                    Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
                    2/25/2022, 9:05:35 PM m119
                    Endstops - X: not stopped, Y: at min stop, Z: no endstop, Z probe: not stopped

                    Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                    npm1undefined 1 Reply Last reply Reply Quote 0
                    • npm1undefined
                      npm1 @npm1
                      last edited by

                      hope that helps

                      Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                      1 Reply Last reply Reply Quote 0
                      • gloomyandyundefined
                        gloomyandy @npm1
                        last edited by

                        @npm1 Are you still using this line for your probe definition:

                        M558 P5 C"!^zstop" H5 F120 T6000

                        If so with the Z driver still removed enter

                        M558 P5 C"zstop" H5 F120 T6000

                        in the console (or change the line in your config.g and reboot)
                        and rerun both sets of tests.

                        npm1undefined 1 Reply Last reply Reply Quote 0
                        • npm1undefined
                          npm1 @gloomyandy
                          last edited by

                          @gloomyandy still no changes, the only thing that change is the z probe value being 1000 instead of zero

                          Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                          npm1undefined 1 Reply Last reply Reply Quote 0
                          • npm1undefined
                            npm1 @npm1
                            last edited by

                            @gloomyandy have I blown something on the board

                            Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                            npm1undefined 1 Reply Last reply Reply Quote 0
                            • npm1undefined
                              npm1 @npm1
                              last edited by

                              shall i update the firmware

                              Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                              npm1undefined 1 Reply Last reply Reply Quote 0
                              • npm1undefined
                                npm1 @npm1
                                last edited by

                                Electronics
                                Diagnostics
                                Board: fly_E3 (STMWiFi)
                                Firmware: RepRapFirmware for STM32F4 based Boards 3.3RC2+1_1 (2021-05-13)
                                Duet WiFi Server Version: 1.26-01S-D

                                Note: You can install updates on the System page.

                                Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                                npm1undefined gloomyandyundefined 2 Replies Last reply Reply Quote 0
                                • npm1undefined
                                  npm1 @npm1
                                  last edited by

                                  will marlin be easier

                                  Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                                  1 Reply Last reply Reply Quote 0
                                  • gloomyandyundefined
                                    gloomyandy @npm1
                                    last edited by gloomyandy

                                    @npm1 Can you turn off your board, disconnect the probe and plug in one of the other endstop switches (x or y) into the zstop socket. Then run the two tests again once without pressing the endstop switch, then again with the endstop switch pressed. Run this test with the Z driver still removed.

                                    npm1undefined 1 Reply Last reply Reply Quote 0
                                    • npm1undefined
                                      npm1 @gloomyandy
                                      last edited by

                                      @gloomyandy endstop works with zero issues with everything triggered correctly

                                      M119

                                      Endstops - X: at min stop, Y: at min stop, Z: at min stop, Z probe: at min stop
                                      2/25/2022, 9:38:20 PM g31
                                      Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
                                      2/25/2022, 9:38:10 PM m119
                                      Endstops - X: at min stop, Y: at min stop, Z: not stopped, Z probe: not stopped

                                      Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                                      npm1undefined 1 Reply Last reply Reply Quote 0
                                      • npm1undefined
                                        npm1 @npm1
                                        last edited by

                                        @gloomyandy the only thing i can think of is to switch the cables on the zstop cables around

                                        Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                                        gloomyandyundefined 1 Reply Last reply Reply Quote 0
                                        • gloomyandyundefined
                                          gloomyandy @npm1
                                          last edited by

                                          @npm1 @npm1 In which case I would be looking very closely at that probe. Are you sure you have correctly identified the various wires? See: https://forum.duet3d.com/topic/25906/inductive-sensor-npn-no-not-working?_=1645824856161 (thanks to Jay for digging that one out).

                                          npm1undefined 1 Reply Last reply Reply Quote 0
                                          • npm1undefined
                                            npm1 @gloomyandy
                                            last edited by

                                            @gloomyandy i knoq that the 5v cable is correctly connected ill switch the cables around and confirm to you shortly

                                            Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                                            npm1undefined 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA