FILAMENT_RUNOUT_DISTANCE_MM or similar at reprap?

apak

@dc42 yes. It´s a direct extruder, but with reversed bowden of 400mm, and at the beginning of the reversed bowden it´s the filament sensor, so It would be nice to extrude at leat 90% of that lenght in order not to waste that filament

apak

@owend Looking at how caribou3d duet handles the sensor
https://github.com/Caribou3d/CaribouDuet2Wifi-ConfigurationMacros

may be, on trigger we could deactivate sensor, continue printing for var runoutDistance, and then trigger pause, reactivate, load an resume

??

T3P3Tony

@apak @OwenD I am working on recreating this issue because it looks like there is a pause happening which should not be happening if the filament-error.g file is present.

T3P3Tony

I have recreated this - and moved it to firmware wishlist section as the behaviour will need to be changed to allow the filament out logic to run without a pause.

OwenD

@t3p3tony
Thanks Tony

apak

@t3p3tony thanks

apak

@t3p3tony does this feature have an ETA?

T3P3Tony

@apak no ETA yet.

DonStauffer

@t3p3tony Tell me if I'm correct:

A workaround should be possible by setting a global variable in filament-error.g if you want to cancel the pause. pause.g checks for the variable, and does an M24 if the variable was set, instead of its usual commands.

Do you think this would work? Or would it skip pause.g if filament-error.g ran, giving you no opportunity to cancel the pause? I'm uncertain whether pause.g gets run or not if filament-error.g exists. I know it's not supposed to.

T3P3Tony

@donstauffer if filament-error.g runs then pause.g does not run AFAIK. The issue is that there is always a pause as part of the process no matter which macro is called.

DonStauffer

@t3p3tony Confirmed. pause.g doesn't run.

OwenD

Just confirming that this is now possible with 3.4.0b7
Albeit you must be aware that the macro called is now filament_error.g, not filament-error.g
i.e. must have an underscore "_" and not a hyphen "-"
There is also a problem if filament_error.g contains an M291 as described here

filament_error.g

;0:/sys/filament_error.g
;run when a filament sensor error is detected.  Print will be paused bt Daemon.g after runout distance.
var runoutDistance = 350 ; this is just so you can change easily 
; first check that we are not currently in an error state and the switch has been toggled again.
if (global.filamentDistance !=0) || !(state.status = "processing")
	echo "Filament sensor triggered, but already no print in progress.  No action taken"
	M99 ; exit macro
echo "filament_error.g run"

G4 P10 ; delay 10ms to debounce
if sensors.filamentMonitors[0].status="ok"
	echo "switch bounce detected - error cancelled"
	M99 ; break out if sensor value is zero again (bouncing)
echo {"Filament error type " ^ param.P ^ " detected on extruder " ^ param.D}
;M291 R"Filament Error" P{"Filament error type " ^ param.P ^ " detected on extruder " ^ param.D} S1 T3

var thisExtruderValue = move.extruders[tools[state.currentTool].filamentExtruder].position
set global.filamentDistance = var.thisExtruderValue + var.runoutDistance
echo "filament_error.g run - print will be paused after " ^ var.runoutDistance ^ "mm"

In daemon.g
(Note this is run in a while loop so it's called at intervals less than 10 seconds)

while true
	; I have a bunch of other stuff in here
	;check the filament runout
	if state.currentTool != -1
		if (move.extruders[tools[state.currentTool].filamentExtruder].position > global.filamentDistance)  &&  (global.filamentDistance !=0) && (state.status = "processing")
			echo "paused called from daemon - filament runout"	
			M25 ; pause print if filament has run out
	G4 S2 ; add a delay for these checks

In resume.g we reset the distance

if sensors.filamentMonitors[0].status="ok"
	set global.filamentDistance = 0 ; reset filament sensor extrusion distance
;do all the other stuff needed for resuming

You also need to set the distance to zero in start.g

if sensors.filamentMonitors[0].status="ok"
	set global.filamentDistance = 0 ; reset filament sensor extrusion distance 
else
	abort "Filament sensor shows no filament loaded.  Print aborted"

and of course define the global in config.g

if !exists(global.filamentDistance)
	global filamentDistance = 0 ; global for use to allow filament to feed for set distance after sensor trips 
else
	set global.filamentDistance = 0

apak

thanks, will try

apak

This post is deleted!

MrTwinkys

@apak any word on whether or not this is functioning correctly? I would like to set this up for a reverse Bowden setup also.