Configuration problems

Dave Parry

OK so Hot end now goes Off Active and standby, but Bed not showing up and these error messages
G28
Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.
Error: Failed to enable endstops

Dave Parry

Oh and no fan controls showing up

fcwilt

@dave-parry said in Configuration problems:

OK so Hot end now goes Off Active and standby, but Bed not showing up and these error messages

Do you have this command after the M950 for the bed heater?

M140 P0 H0 ; map heated bed to heater 0

G28

Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.
Error: Failed to enable endstops

Correct.

What used to be G1 S1 is now G1 H1.

Just edit your homing files.

Frederick

Dave Parry

Have bed temps working now, many thanks.
Homing not working because of end stops Not enabled.
Is that similar to temp sensors?

Dave Parry

I just checked and I have
M574 X2 Y2 Z2 S1 ; set active high endstops

Wiki says they have to be seperate lines

Dave Parry

OK so now I get it to home and move down 5mm and home again, but it then should move down and centre. but it stays with end stops activated and I get message Error: G0/G1: target position not reachable from current position

File is
; homedelta.g
; called to home all towers on a delta printer
;
; generated by RepRapFirmware Configuration Tool v3.3.2 on Thu Sep 02 2021 19:22:19 GMT+0100 (British Summer Time)
G91 ; relative positioning
;*** Slow homing has been configured. Change F180 to F1800 below when your configuration is working
G1 H1 X265 Y265 Z265 F2500 ; move all towers to the high end stopping at the endstops (first pass)
G1 H2 X-5 Y-5 Z-5 F1800 ; go down a few mm
;*** Slow homing has been configured. Change F180 to F360 below when your configuration is working
G1 H1 X10 Y10 Z10 F180 ; move all towers up once more (second pass)
G1 Z-5 F2400 ; move down a few mm so that the nozzle can be centred
G90 ; absolute positioning
G1 X0 Y0 F2400 ; move X+Y to the centre

fcwilt

@dave-parry said in Configuration problems:

I just checked and I have
M574 X2 Y2 Z2 S1 ; set active high endstops

Wiki says they have to be seperate lines

Correct.

Dave Parry

Seem to think that error message is related to homed height, but just tried adding 5mm to homed height no different and then tried subtracting 5mm same.

fcwilt

@dave-parry said in Configuration problems:

Seem to think that error message is related to homed height, but just tried adding 5mm to homed height no different and then tried subtracting 5mm same.

Replace that G1 Z-5 with G1 H2 X-5 Y-5 Z-5 - that should do it.

Frederick

Dave Parry

It homes ok but I still get
G28
Error: G0/G1: target position not reachable from current position

fcwilt

@dave-parry said in Configuration problems:

It homes ok but I still get
G28
Error: G0/G1: target position not reachable from current position

Even with that change I suggested?

Curious.

Frederick

Dave Parry

sorted that out Frederick, the default end stop setting says
active high endstop switch but X1 is low end it needs to be X2

Dave Parry

Just need to sort fan control not showing and M106 not doing anything either. Think it's because they havent been properly configured.

fcwilt

@dave-parry said in Configuration problems:

Just need to sort fan control not showing

Need to see you most recent fan code. It may be still back at v2 syntax.

Frederick

Dave Parry

Think your right

; Fans
M106 P0 S0 I0 F500 H-1 C"Part Clg" ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S0 I0 F500 H-1 C"Bed Clg" ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off

fcwilt

@dave-parry said in Configuration problems:

Think your right

; Fans
M106 P0 S0 I0 F500 H-1 C"Part Clg" ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S0 I0 F500 H-1 C"Bed Clg" ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off

Yes - that's v2 syntax.

Here is my code for two fans:

; ****************************************************************************************************
; cooling fans
; -- P# is fan, S# is speed (0 to 255 or 0.0 to 1.0) H# means turn on fan when heater H# temp hits T#
; -- H-1 means no thermostatic control
; ****************************************************************************************************

M950 F0 C"fan0" Q500        ; create fan (F), pin name (C), frequency (Q)
M106 P0 C"Part" S0 H-1      ; set fan (P), name (C), speed (S), thermostatic control off (H)

M950 F1 C"fan1" Q500        ; create fan (F), pin name (C), frequency (Q)
M106 P1 C"Hotend" S1 H1 T45 ; set fan (P), name (C), speed (S), thermostatic control on (H & T)

Dave Parry

@fcwilt said in Configuration problems:

M950 F0 C"fan0" Q500 ; create fan (F), pin name (C), frequency (Q)

Have got them working with this

M950 F0 C"fan0"
M950 F1 C"fan1"
M106 P0 S0 I0 F500 H-1 C"Part Clg" ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S0 I0 F500 H-1 C"Bed Clg"

But have tool fan on there as well which also starts part fan

Dave Parry

Tried rem ing out fan0 but then tool fan controls do nothing

Dave Parry

Just noticed that the tool fan shows when the hot end is active and when hot end is off or standby is hidden.
I either need to hide it completely or get rid of the part fan control but have the tool fan control that fan

fcwilt

@dave-parry said in Configuration problems:

Just noticed that the tool fan shows when the hot end is active and when hot end is off or standby is hidden.
I either need to hide it completely or get rid of the part fan control but have the tool fan control that fan

That tool fan display is controlled by the DWC.

It's just a way of having a single consistently named control in those cases where you might have multiple tools each with their own fan.

You can control the visibility of the actual part fan from the DWC.

Frederick