Resurrect.g problem

3Dream

Config.g

M80 ; power on
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Pluto" ; set printer name
M669 K1 ; select CoreXY mode

; Network
M552 P192.168.44.30 S1
M554 P192.168.44.1
M553 P255.255.255.0
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S0 ; physical drive 0 goes forwards
M569 P1 S0 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M569 P4 S0 ; physical drive 4 goes forwards
M584 X0 Y1 Z2 E3:4 ; set drive mapping
M350 X128 Y128 Z32 E16:16 I0 ; configure microstepping with interpolation
M92 X641.50 Y641.50 Z1280.00 E460.00:460.00 ; set steps per mm
M566 X800.00 Y800.00 Z60.00 E120.00:120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z1200.00 E3000.00:3000.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z80.00 E250.00:250.00 ; set accelerations (mm/s^2)
M906 X1600 Y1600 Z1400 E700:700 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X-18.5 Y-1.5 Z0 S1 ; set axis minima
M208 X340 Y300 Z302.5 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"^xstop" ; configure active-high endstop for low end on X via pin ^xstop
M574 Y1 S1 P"^ystop" ; configure active-high endstop for low end on Y via pin ^ystop
M574 Z2 S1 P"^zstop" ; configure active-high endstop for high end on Z via pin ^zstop

; Z-Probe
M558 P5 C"^!zprobe.in" H3 F120 T12000 ; set Z probe type to unmodulated and the dive height + speeds
G31 P600 X23 Y13.5 Z0.3 ; set Z probe trigger value, offset and trigger height
M557 X18:295 Y20:290 S90 ; define mesh grid

; Heaters
;Piano
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S150 ; set temperature limit for heater 0 to 150C
M570 H0 P1000000 S1000000
;Estrusore SX
M308 S1 P"e0temp" Y"pt1000" ; configure sensor 1 as PT1000 via CS pin spi.cs1
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 R3.082 C205.660:205.660 D5.75 S1.00 V24.2 B0; disable bang-bang mode for heater and set PWM limit
M143 H1 S400 ; set temperature limit for heater 1 to 400C
M570 H1 P1000000 S1000000
;Estrusore DX
M308 S2 P"e1temp" Y"pt1000" ; configure sensor 2 as PT1000 via CS pin spi.cs2
M950 H2 C"e1heat" T2 ; create nozzle heater output on e0heat and map it to sensor 2
M307 H2 R2.931 C222.886:222.886 D5.16 S1.00 V24.2 B0; disable bang-bang mode for heater and set PWM limit
M143 H2 S400 ; set temperature limit for heater 2 to 400C
M570 H2 P1000000 S1000000
;Camera
M308 S3 P"duex.e6temp" Y"thermistor" T100000 B4138 ; configure sensor 3 as thermistor on pin e0temp
M950 H3 C"!exp.heater3" T3 ; create chamber heater output on e7heat and map it to sensor 3 ( ! inverte logica uscita )
M307 H3 B1 S1.00 ; enable bang-bang mode for the chamber heater and set PWM limit
M141 H3 ; map chamber to heater 2
M143 H3 S80 ; set temperature limit for Chamber to 80C
M570 H3 P1000000 S1000000

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off

; Tools
M563 P0 S"Extr sx" D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
M563 P1 S"Extr dx" D1 H2 F0 ; define tool 1
G10 P1 X-17.4 Y0.00 Z0 ; set tool 1 axis offsets
G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C

;Filament Sensor
M591 D0 P1 C"^e0stop" S1
M591 D1 P1 C"^e1stop" S1

; Miscellaneous
M911 S22 R0 P"M913 X0 Y0 G91 M83 G1 Z10 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T0 ; select first tool

3Dream

Resurrect prologue.g

M116 ; wait for temperatures
G28 ; home all towers
M83 ; relative extrusion
G1 E10 F600 ; undo the retraction that was done in the M911 power fail script
G4 S5
G1 Y50 F5000; Mi muovo per togliere il filo
G1 Y0 F5000
G1 Y50 F5000

Actual resurrect.g

; File "0:/gcodes/bloccaggio-a-pressione-definitivo-v2.gcode" resume print after power failure at 2021-04-13 14:34
G21
M141 P0 S40.0
G29 S1
T-1 P0
G92 X128.952 Y115.714 Z0.650
G60 S1
G10 P1 S23 R0
G10 P0 S240 R240
T0 P0
M98 P"resurrect-prologue.g"
M116
M290 X0.000 Y0.000 Z0.000 R0
T-1 P0
T0 P6
; Workplace coordinates
G10 L2 P1 X0.00 Y0.00 Z0.00
G10 L2 P2 X0.00 Y0.00 Z0.00
G10 L2 P3 X0.00 Y0.00 Z0.00
G10 L2 P4 X0.00 Y0.00 Z0.00
G10 L2 P5 X0.00 Y0.00 Z0.00
G10 L2 P6 X0.00 Y0.00 Z0.00
G10 L2 P7 X0.00 Y0.00 Z0.00
G10 L2 P8 X0.00 Y0.00 Z0.00
G10 L2 P9 X0.00 Y0.00 Z0.00
G54
M106 S0.00
M116
G92 E12.78310
M82
M23 "0:/gcodes/bloccaggio-a-pressione-definitivo-v2.gcode"
M26 S13452 P1.015 X118.520 Y115.714
G0 F6000 Z2.650
G0 F6000 X128.952 Y115.714
G0 F6000 Z0.650
G1 F450.0 P0
G21
M24

dc42

@3dream, I confirm that this is a bug. Bed and chamber heat on/off and temperature settings are not written to resurrect.g.

3Dream

@dc42
Good morning,
Thanks for the reply
The temperature of the extruder and chamber are recorded.
is there any way around this?
I would prefer that the chamber does not turn on again or at least that the machine does not wait to reach its temperature before starting.
While the bed would need to be registered.

dc42

@3dream, why would you not want to restore chamber heat before the print is resurrected?

The workaround is that before you resurrect a print, manually set the bed temperature to the required value.

3Dream

@dc42 because the chamber temperature is also reached thanks to the bed. If I forget to activate the bed before pressing resume I cannot activate it again until I reach the chamber temperature. However, it takes a long time to reach the chamber temperature if it has been left very high.
Instead of waiting for the chamber target it could activate but not wait to reach it (like M104).
When do you think you can close this hole? I would really appreciate it
Thank you

dc42

@3Dream, you could turn off the chamber heat in resurrect-prologue.g before the M116 command. Or you could leave it on, but use a more selective M116 command that doesn't wait for the chamber temperature.

dc42

I've found the bug that was causing the bed heater state not to be written to resurrect.g when there was also a chamber heater. The fix will be in firmware 3.3beta3.

3Dream

@dc42 , Ok, but first the resurrection is read where M141 starts for the chamber and only then is the right prologue read? Therefore it would still wait for the chamber temperature before advancing. Or am I wrong?

dc42

@3dream, M141 does not wait for temperature to be reached.

3Dream

@dc42 Thank you
It worked for the chamber