BL Touch sanity check, please

Phaedrux

Can you test the BLT on the mainboard to see if it will powerup and self-test? Even just connecting 5v should have it do a test.

Is the BLT upright when doing this? If it's on it's side it won't work the pin correctly. It must be vertical to function.

PaulHew

@Phaedrux Thanks for the prompt reply, it is appreciated as always.

Have plugged into io.0 on the board, no self test but lights up red.
Dead BLT?

P.

Phaedrux

Hmmm. Well you say it's known working? When was it last working? Does it work there now?

PaulHew

I have ordered another blt 3.1 which will be here tomorrow.

That will be the definitive way!

Thanks again @Phaedrux

Paul.

PaulHew

My new v3.1 BLT turned up today.
Checked it worked on bench with only pos and neg connected, fired pin 3 times.

Plugged into my wiring after checking for the Nth time, powered up, lights red but no self test.

Tested original cable, wired new one in still no joy.

Back to the bench and both new and old BLT's work with 5v power in regards to power on test.
Tested both on Mini+ IO_0, both completed self test.

wired ONLY the pos and gnd/neg wires into the toolboard and powered up, self test completes.
Yellow and white were not connected.

Reason why I thought it had failed last night and ordered another because I still had yellow and white connected on the toolboard whilst powering it with IO_0 on the Mini.

I think I have a faulty toolboard, is there anything else I can checked to clarify?

Regards,

Paul.

PaulHew

Trying something.
Power for BLT on toolboard, IO control on io_1 on Mini 5+
Configured, shutdown, wait 10secs, powered up, self test completes.

Sent the test commands M280 P0 S10 and M280 P0 S90 and these push the pin out and retract the pin as expected.

So power on the toolboard is ok, Self test does not complete when IO connected to the toolboard.
IO on the Mini5+ - BLT self tests and responds to commands.

Regards,

Paul

Phaedrux

@paulhew Hmm. I'm not sure if that's normal or not. Will check with DC42.

PaulHew

@phaedrux Appreciate that it is DC42's call.
IMO, pretty conclusive.
When all connections for the BLT are on the toolboard it does not self test or respond to commands.
When the io_in and out are on io_1 on the mainbaoard, it works as it should.
Also when only power is applied with no connections to orange and white wires, it self tests correctly.

Regards,

Paul

droftarts

@paulhew I remembered that this has been an issue for other people. Please can you see if this thread is relevant? https://forum.duet3d.com/topic/19211/bltouch-and-duet-3-tool-board

Edit: basically, check the bootloader version on the toolboard, and update it. See https://duet3d.dozuki.com/Wiki/Updating_the_bootloader_on_Duet_3_expansion_and_tool_boards

Ian

PaulHew

@droftarts Thanks for the info Ian.
My current Info from the 1LC

m122 b20
Diagnostics for board 20:
Duet TOOL1LC firmware version 3.2.2 (2021-02-11)
Bootloader ID: not available
Never used RAM 4032, free system stack 94 words
HEAT 90 CanAsync 89 CanRecv 83 TMC 56 MAIN 218 AIN 64
Last reset 00:02:03 ago, cause: software
Last software reset data not available
Driver 0: position 0, 412.0 steps/mm, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 28, reads 61567, writes 12, timeouts 0, DMA errors 0
Moves scheduled 0, completed 0, in progress 0, hiccups 0
No step interrupt scheduled
VIN: 24.3V
MCU temperature: min 23.3C, current 24.0C, max 25.1C
Ticks since heat task active 192, ADC conversions started 122890, completed 122888, timed out 0
Last sensors broadcast 0x00000002 found 1 195 ticks ago, loop time 0
CAN messages queued 973, send timeouts 43, received 714, lost 0, free buffers 36

No bootloader info... Oh well, hope Tony has a spare board if this goes pear shaped!

P.

PaulHew

So issued the command
M997 B20 S3
Tool fan spun up and so far 2 mins in nothing else has happened

M997 B20 S3
Board 20 starting bootloader update

Restarted the machine and now have this...

m122 b20
Diagnostics for board 20:
Duet TOOL1LC firmware version 3.2.2 (2021-02-11)
Bootloader ID: SAMC21 bootloader version 2.3 (2021-01-26b1)
Never used RAM 4032, free system stack 94 words
HEAT 90 CanAsync 89 CanRecv 83 TMC 66 MAIN 218 AIN 70
Last reset 00:00:13 ago, cause: software
Last software reset data not available
Driver 0: position 0, 412.0 steps/mm, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 51, reads 6920, writes 12, timeouts 0, DMA errors 0
Moves scheduled 0, completed 0, in progress 0, hiccups 0
No step interrupt scheduled
VIN: 24.3V
MCU temperature: min 23.6C, current 23.6C, max 23.7C
Ticks since heat task active 148, ADC conversions started 13850, completed 13849, timed out 0
Last sensors broadcast 0x00000002 found 1 151 ticks ago, loop time 0
CAN messages queued 160, send timeouts 0, received 134, lost 0, free buffers 36

seems to be working with M280 P0 S10 and S90. Will test tomorrow after I have redone my Z offsets....