Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    correctly Config for my Fan

    Scheduled Pinned Locked Moved
    Config Tool
    3
    12
    334
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • chuserundefined
      chuser
      last edited by

      I have a DICE Printer.
      my FAN Config
      M950 F0 C"out3" Q500
      M950 F1 C"out5" Q500
      M950 F2 C"out6" Q500

      out5 and out6 also work.
      But out3 burns my fans (Sunon MC30060V2-00U-A99).
      Measured at the fan 5V arrive.

      But the fan is already on strike at 50%.
      Can someone help me?

      Here the wirring
      DuetWiring 2.png

      fcwiltundefined 1 Reply Last reply Reply Quote 0
      • fcwiltundefined
        fcwilt @chuser
        last edited by

        @chuser said in correctly Config for my Fan:

        out5 and out6 also work.

        Are you saying that out5 and out6 are working correctly?

        But out3 burns my fans (Sunon MC30060V2-00U-A99).

        What do you mean by "burns"?

        Measured at the fan 5V arrive.

        Are you saying you have measured that the outputs are providing 5 volts?

        But the fan is already on strike at 50%.

        What does that mean?

        Frederick

        Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

        1 Reply Last reply Reply Quote 0
        • chuserundefined
          chuser
          last edited by

          Thank you for your Answer.

          @fcwilt said in correctly Config for my Fan:

          Are you saying that out5 and out6 are working correctly?

          yes working correctly

          What do you mean by "burns"?

          The fan rotate, then stops and smokes and that already at 50%

          Are you saying you have measured that the outputs are providing 5 volts?

          yes corretly

          fcwiltundefined 1 Reply Last reply Reply Quote 0
          • fcwiltundefined
            fcwilt @chuser
            last edited by

            @chuser said in correctly Config for my Fan:

            What do you mean by "burns"?

            The fan rotate, then stops and smokes and that already at 50%

            Not all fans can be controlled with PWM to vary the speed.

            Perhaps the one that is smoking is one of those that cannot be controlled.

            If it is still working try 100% - that feeds un-pulsed power to the fan just as if was receiving power from a 5 volt DC source.

            Frederick

            Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

            1 Reply Last reply Reply Quote 0
            • chuserundefined
              chuser
              last edited by

              Thanks for the tip

              I tried that but it did not work.
              The fan spins for about 5 seconds and then it stops.

              And I noticed now that as soon as the fan stops the board reboot. no smoke appears.
              Isn't there a possibility to use the out3 withouth PWM?

              fcwiltundefined 1 Reply Last reply Reply Quote 0
              • fcwiltundefined
                fcwilt @chuser
                last edited by

                @chuser said in correctly Config for my Fan:

                Thanks for the tip

                I tried that but it did not work.
                The fan spins for about 5 seconds and then it stops.

                And I noticed now that as soon as the fan stops the board reboot. no smoke appears.
                Isn't there a possibility to use the out3 withouth PWM?

                Perhaps you are drawing more current than the on-board power 5 volt power supply can provide?

                It's limited to about 700ma according to the docs.

                That would explain why the board re-boots.

                Frederick

                Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

                chuserundefined 1 Reply Last reply Reply Quote 0
                • chuserundefined
                  chuser @fcwilt
                  last edited by

                  @fcwilt

                  The fan which makes troubles has only 0.072mA - in my opinion that shouldn‘t be the reason for re-booting
                  What do ya think?

                  1 Reply Last reply Reply Quote 0
                  • Phaedruxundefined
                    Phaedrux Moderator
                    last edited by Phaedrux

                    If you don't need PWM control or switching, can you connect it directly to a 5v source and run it as always on?

                    Is this the fan?
                    https://www.mouser.ca/ProductDetail/Sunon/MC30060V2-000U-A99?qs=EU6FO9ffTwdvsqO4GP3Tbg==

                    Z-Bot CoreXY Build | Thingiverse Profile

                    chuserundefined 1 Reply Last reply Reply Quote 0
                    • chuserundefined
                      chuser @Phaedrux
                      last edited by

                      @Phaedrux yes its this type of fan.

                      I will do a test run tomorrow and will let you know!

                      1 Reply Last reply Reply Quote 0
                      • Phaedruxundefined
                        Phaedrux Moderator
                        last edited by

                        Does the fan work on the other ports without issue?

                        Z-Bot CoreXY Build | Thingiverse Profile

                        1 Reply Last reply Reply Quote 0
                        • chuserundefined
                          chuser
                          last edited by

                          @fcwilt @Phaedrux Thank you very much for the help.

                          I have measured the power current of the fan and found that it is too much. The current of the fan rised above 1A after a short time.

                          I have replaced the fan and now everything works.

                          fcwiltundefined 1 Reply Last reply Reply Quote 1
                          • fcwiltundefined
                            fcwilt @chuser
                            last edited by

                            @chuser said in correctly Config for my Fan:

                            @fcwilt @Phaedrux Thank you very much for the help.

                            I have measured the power current of the fan and found that it is too much. The current of the fan rised above 1A after a short time.

                            I have replaced the fan and now everything works.

                            So it turned out to be the fan that was causing the reset as we suspected.

                            Glad to hear you got it all sorted.

                            Frederick

                            Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

                            1 Reply Last reply Reply Quote 0
                            • First post
                              Last post
                            Unless otherwise noted, all forum content is licensed under CC-BY-SA