Independently leveled Z axis Issue

[fcwilt]

@mrenz999 said in Independently leveled Z axis Issue:

@3DPrintingWorld In your bed.g do you have it do multiple probes per point ? If so how do you accomplish that ?

Read up about the A and S parameters of M558.

If A = 10 and S=0.01 the process will probe each point up to 10 times trying to get two consecutive readings with 0.01.

If it fails to do that it will average all 10 readings.

Frederick

[mrenz999]

@fcwilt Perfect. Thank you. Does it matter where in the M558 I put that ?

[fcwilt]

@mrenz999 said in Independently leveled Z axis Issue:

Yes thats the one Except I have 3 z motors. 2 on the right side and 1 on the left

And the linear guides are on the underside of the top most frame pieces?

Frederick

[fcwilt]

@mrenz999 said in Independently leveled Z axis Issue:

@fcwilt Perfect. Thank you. Does it matter where in the M558 I put that ?

No just add them to your current M558 command.

Frederick

[mrenz999]

@fcwilt

[fcwilt]

@mrenz999

Sorry but I cannot tell where they are from that picture - I may be looking right at them and just not seeing them.

So where are the left and right linear guides mounted?

Thanks.

Frederick

[mrenz999]

@fcwilt So the left one is in the middle of the bed on the X axis. The 2 on the right are at the corners of the bed frame. The bed frame sits on the attachment to the linear guide mounts

[fcwilt]

@mrenz999 said in Independently leveled Z axis Issue:

@fcwilt So the left one is in the middle of the bed on the X axis. The 2 on the right are at the corners of the bed frame. The bed frame sits on the attachment to the linear guide mounts

Sorry I was not clear - I meant the Y axis guides - the ones running front to back on each side.

Frederick

[mrenz999]

@fcwilt gotcha. The are underneath

[3DPrintingWorld]

@mrenz999 said in Independently leveled Z axis Issue:

@3DPrintingWorld In your bed.g do you have it do multiple probes per point ? If so how do you accomplish that ?

I created a macro that heats the bed, calls out the mesh, homes, does the mesh, saves the mesh, then turns the bed off. I started at 10:10, then S= was my max travel minus 10. Plus you have to add/subtract your probe to nozzle offset.

M140 S60
M557 X10:365 Y10:290 S300:270
G28
G29 S0
G29 S3
M140 S0

[fcwilt]

@mrenz999

Great.

Did you print out those "tools" designed to help align the frame pieces?

I didn't have such tools and after seeing my 4 point height map I realized that my left and right Y axis guides were not in the same plane meaning the frame pieces were not in the same plane.

I closely examined the left and right frame pieces where they joined the four vertical pieces at the top and found that they were at slightly different heights, with the left piece being low in the rear and right piece being high in the front.

We are talking fractions of a mm but it was enough to generate a "twisted" height map - though not as bad as yours.

Perhaps you are having the same problem.

Frederick

[3DPrintingWorld]

@mrenz999

Looks like one of your bearings is not attached?


[mrenz999]

@fcwilt Perhaps. I did print the tool but things move so I will recheck them.
Is there a way to add the a and s parameter to your bed.g when doing the leveling so it does multiple probes ?

[fcwilt]

@3DPrintingWorld said in Independently leveled Z axis Issue:

M140 S60
M557 X10:365 Y10:290 S300:270
G28
G29 S0
G29 S3
M140 S0

Why the G29 S3? The G29 S0 creates the height map and loads it.

Frederick

[mrenz999]

@3DPrintingWorld I pulled screws out of all of them and started a retighten. Trying to see if something came loose.

[fcwilt]

@mrenz999 said in Independently leveled Z axis Issue:

@fcwilt Perhaps. I did print the tool but things move so I will recheck them.
Is there a way to add the a and s parameter to your bed.g when doing the leveling so it does multiple probes ?

Yes but is there some reason you cannot modify the existing M558?

Frederick

[3DPrintingWorld]

@mrenz999 said in Independently leveled Z axis Issue:

@3DPrintingWorld I pulled screws out of all of them and started a retighten. Trying to see if something came loose.

Ok, that makes sense.

[mrenz999]

I can but does that affect the bed leveling as well ?

[fcwilt]

@mrenz999 said in Independently leveled Z axis Issue:

I can but does that affect the bed leveling as well ?

If affects the way the probe works where ever it is used.

Do you wish to have it behave in different ways in different places?

Frederick

[mrenz999]

@fcwilt Not necessarily. I just want it to do multiple probes when it checks bed leveling when I home the printer.