Duet 3 6HC Output_0 always on
-
@razrudy said in Duet 3 6HC Output_0 always on:
Also the OUT_0 output is controlling a mosfet ( that's the reason for that "thick" wires on output )
I also have separate PSU for the bed controlled by the mosfet.Why is the OUT_0 output controlling a MOSFET?
Frederick
-
This is my working config , not complete but everything works
Configuration file for Duet 3 (firmware version 3) ; Configuration for Chiron+Titan Aero+Volcano+BlTouch+ SBC Pi4 ; executed by the firmware on start-up ; General preferences G21 ; works in mm G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Chiron" ; set printer name ; Drives M569 P0.0 S1 ; physical drive 0.0 goes forwards X M569 P0.1 S0 ; physical drive 0.1 goes backwards Y M569 P0.2 S0 ; physical drive 0.2 goes bacwards ZL M569 P0.3 S0 ; physical drive 0.3 goes backwards ZR M569 P0.4 S1 D2 ; physical drive 0.4 goes forwards E M584 X0 Y1 Z2:3 E4 ; set drive mapping M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X80 Y100 Z400 E400.96 ; set steps per mm ;M566 X1200 Y1200 Z12 E120 ; set maximum instantaneous speed changes (mm/min) M566 X600 Y360 Z24 E1200 ; in mm/min-Marlin values ;M203 X9000 Y9000 Z180 E1200 ; set maximum speeds (mm/min) M203 X6000 Y6000 Z1200 E4800 ; set maximum speeds-Marlin values transform to mm/m ;M201 X1000 Y800 Z250 E250 ; set accelerations (mm/s^2) M201 X350 Y350 Z50 E30000 ; set accelerations-Marlin values M906 X1100 Y1100 Z1100 E1100 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X-6.0 Y-9.0 Z-20 S1 ; set axis minima M208 X400 Y400 Z445 S0 ; set axis maxima-need to remeasure this M671 X-40:440 Y200:200 ; leadscrews position at right and left of the X axis ; Endstops M574 X1 S1 P"!io0.in" ; configure active-high endstop for low end on X via pin io0.in M574 Y1 S1 P"!io1.in" ; configure active-high endstop for low end on Y via pin io1.in ;M574 Z1 S1 P"io2.in+io3.in" ; configure active-high endstop for low end on Z via pin-for original endstop's M574 Z1 S2 ; endstop set to z-probe ;Stall Detection ;M915 P0 S-5 F0 H200 R0 ; P=drive motor , S= sensitivite , H=motorstep/sec ( check home file) ; Z-Probe M950 S0 C"io5.out" ; create servo pin 0 for BLTouch M558 P9 C"^io5.in" H5 F60 T6000 R0.2 A10 ; set Z probe type to bltouch and the dive height + speeds G31 P25 X41.13 Y2.69 Z1.537 ; set Z probe trigger value, offset and trigger height M557 X40:400 Y0:400 S72:80 ; define mesh grid ; Piezo Z-probe ;M558 P8 C"io5.in" I1 R0.4 F300 X0 Y0 Z1 ;new piezo ;G31 X0 Y0 Z-0.1 P100 ;new piezo ; Heaters M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0 M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0 M307 H0 R0.286 C453.000:453.000 D1.10 S0.50 V24.0 B0 ; disable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M308 S1 P"temp1" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin temp1 M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1 M307 H1 R1.840 C275.300:275.300 D4.10 S0.50 V24.0 B0 ; disable bang-bang mode for heater and set PWM limit M143 H1 S285 ; set temperature limit for heater 1 to 285C ; Fans M950 F0 C"out4" Q25000 ; create fan 0 on pin out4 and set its frequency M106 P0 S0 H1 T45 ; set fan 0 value. Thermostatic control is turned on M950 F1 C"out5" Q25000 ; create fan 1 on pin out5 and set its frequency M106 P1 S0 H1 T45 ; set fan 1 value. Thermostatic control is turned on M950 F2 C"out7" Q25000 ; create fan 2 on pin out7 and set its frequency M106 P2 S0 H-1 ; set fan 2 value. Thermostatic control is turned off ;M950 F3 C"out8" Q500 ; create fan 3 on pin out8 and set its frequency ;M106 P3 S0 H-1 ; set fan 3 value. Thermostatic control is turned off ; Tools M563 P0 D0 H1 F0:2 ; define tool 0 G10 P0 X-6.0 Y-7.0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not defined M572 D0.4 S0.05 ; Miscellaneous ;M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss ;M564 H0 ; moving axes before/without homing ;M591 P1 C"io4.in" S1 D0 ; filament run out sensor - work in progress
M308 and M950 are not on the same order. Not sure how important is
-
@razrudy I don't think this is config related as replacing my config with a default one, or not one at all the same behavior exists.
@fcwilt I don't know. Could that be related to the fuse that I replaced that was loose at the start that was causing the bed to power on and off randomly? Or something else?
-
@fcwilt said in Duet 3 6HC Output_0 always on:
@razrudy said in Duet 3 6HC Output_0 always on:
Also the OUT_0 output is controlling a mosfet ( that's the reason for that "thick" wires on output )
I also have separate PSU for the bed controlled by the mosfet.Why is the OUT_0 output controlling a MOSFET?
Frederick
Separate PSU for bed. Is there any other way to control the mosfet?
-
@razrudy said in Duet 3 6HC Output_0 always on:
Separate PSU for bed. Is there any other way to control the mosfet?
The 6HC has the separate power input for OUT 0. If the current rating of OUT 0 is adequate you can connect the bed power supply to OUT 0 POWER IN and the bed directly to OUT 0.
Just verify that the grounds of both power supplies are connected together if the two board ground connections are not.
Frederick
-
I've tried this with seperate supplies, the same supply and new power supplies to no change in the problem I'm experiencing so I don't think it's related to the power suppl(y/ies).
-
-
@razrudy That was my conclusion as well but per Filastruder I have to have a mod/admin approve to get an RMA issued.
-
@razrudy said in Duet 3 6HC Output_0 always on:
@fcwilt 1000W 40A PSU too much for the board
Your bed heater draws 40 amps?
Wow.
Frederick
-
It would appear that the mosfet for Out_0 has failed closed. Not a good situation. Please contact your vendor and initiate a warranty exchange and include a link to this thread as authorization.
-
Can you see any damage or something on the mosfet on the board? Maybe one "leg" is not soldered properly
-