Duet 3 mini 5+ sensorless homing will not work

fcwilt

@Alucardi said in Duet 3 mini can't configure sensorless homing + missing extruder:

played around with different move types and all i could find. Still no go.

As I understand it this is a CoreXY machine.

Why are your X and Y motor settings not the same?

Why are you using G1 H3 moves?

Thanks.

Frederick

Alucardi

@gloomyandy do not work.

Alucardi

@fcwilt how should I move the axis then if not using g1? Should I not use H? In the guide it says to use it. I have tried H1/2/3/4 just to see if it makes any different but it does not.

fcwilt

@Alucardi said in Duet 3 mini can't configure sensorless homing + missing extruder:

@fcwilt how should I move the axis then if not using g1? Should I not use H? In the guide it says to use it. I have tried H1/2/3/4 just to see if it makes any different but it does not.

You are trying to home the X and Y axes to test sensorless homing - correct?

If that is the case G1 H1 is the correct variant to use.

And what about the motor settings being different for X and Y?

Frederick

Alucardi

@fcwilt it makes no difference what h I use. Be look further up and you will see that I used h1 also. S value is difference cause I can then test 2 values at the same time. But it makes for no difference if I use -64 or 64 it still will not detect a stall.

Alucardi

@fcwilt here is a new config still same issue it makes no difference what i do.

M400							; finishes all current moves and and thus clears the buffer
M913 X50 Y34 					; drop motor current to 33%
M569 P0.0 D3 V60   		 		; reduce V to ensure stealthChop is enabled
M569 P0.1 D3 V60   		 		; reduce V to ensure stealthChop is enabled
M915 P0.0 S-50 R0 F0 H400		; sensitivity X, don’t take action, don’t filter
M915 P0.1 S-50 R0 F0 H400		; sensitivity Y, don’t take action, don’t filter
M400 							; finishes all current moves and and thus clears the buffer
G91								; relative positioning
G1 H1 Z10 F6000	    	   		; lift Z relative to current position
G1 H1 X1
G4 P200
G1 H1 X20 F8000
G1 H1 X-335 F5000		   		; move to X
G1 H1 X5 F7000
G1 H1 Y1
G4 P200
G1 H1 Y20 F8000
G1 H1 Y-348 F5000 				; move to Y
G30 P0 G1 X167.5 Y167.5    		; home Z by probing the bed
G90                   	  		; absolute positioning
M400							; finishes all current moves and and thus clears the buffer
M569 P0.0 P0.1 D2      			; restore default for motor
M913 X100 Y100 					; return current to 100%
M400							; finishes all current moves and and thus clears the buffer

fcwilt

@Alucardi said in Duet 3 mini can't configure sensorless homing + missing extruder:

@fcwilt here is a new config still same issue it makes no difference what i do.

OK I will give it a go on my Duet 3 Mini and see if I can get it to work.

This will take a bit of time.

Frederick

fcwilt

@Alucardi

Well I got it to function on my work bench BUT it was erratic - failing more often than working.

Certainly not reliable enough to use.

If I find the problem I will let you know.

Frederick

Phaedrux

@fcwilt What settings did you end up with?

fcwilt

@Phaedrux said in Duet 3 mini can't configure sensorless homing + missing extruder:

@fcwilt What settings did you end up with?

You would ask me that. Let's see...

I basically followed the documentation and used the suggested values.

The following were already in the config file that I was using for testing my new board:

M92 X80
M201 X1000
M203 X10000
M566 X600
M906 X1000 I30

These I added for testing:

M569 P0 S1 V?? (I cannot remember V but it set the crossover speed around 180 mm/s)
M574 X2 S3 (the doc example has M574 X Y S3 which is missing the X and Y values)
M913 X70
M915 X S1 F0 H400 R1 (0.9 stepper - I just grabbed a handy one)

The "home" command was G91 G1 H1 X999 F10000 G90

Now I have never tried this before and I wasn't going to spend a lot of time trying to tweak it.

I was content to verify that it did work sometimes and perhaps just needed different settings or perhaps a different
stepper.

Back to my trusty optical end stop sensors.

Frederick

Alucardi

@fcwilt I don’t see what I am missing. My stepper works fine with my old board I guess I am sol. Others have made it work. Think I have a defective board or is it that firmware is not working as it should? Cause it seem like all I find are people having issues.

Edit: I did find this. But it is unclear if I should use s3 or s4. S4 says it stops the motors individuality but I don’t want that. S3 refers to be used with only 1 motor so I should not use that either. So what should I use?

fcwilt

@Alucardi said in Duet 3 mini 5+ sensorless homing will not work:

@fcwilt I don’t see what I am missing. My stepper works fine with my old board I guess I am sol. Others have made it work. Think I have a defective board or is it that firmware is not working as it should? Cause it seem like all I find are people having issues.

I wouldn't exactly say I got it to work. It worked maybe 1 time out of 10 tries.

~~For a Core XY I THINK you would use S4 so each motor would keep moving until it stalled.~~

OK so it turns out you use S3.

Did I mention that optical end stop sensors work great?

Frederick

Phaedrux

S4 is intended for Z axis leveling with multiple motors but instead of endstops stall detection.

Alucardi

@fcwilt I will not redesign my printer setup to use endstops. The card says it support sensorless homing so that feature should work right? It has worked fine for years using duet 2 card. It took me 2 minutes to get it setup there and now it is a pain in the but.
Regarding s3 it clearly says single motor. A coreXY don’t have a single motor ‍️
Unless @dc42 have a suggestion it is time for me to leave rrf and move over to klipper where I know sensorless homing works with 2209 drivers.

oliof

Did you follow @gloomyandy s suggestion to try the inverted sensitivity setting?

Alucardi

@oliof yes I replied to him and said it did not work using 64. At -64 it should trigger directly which it does not. It does not even trigger which means something is not working. Either it is a broken firmware or wrong code we can’t figure out.
I believe it to be firmware though since even if downloading 3.2 firmware we are stuck on beta, Wonder why they don’t fix that ‍️

oliof

~~I'll try a small setup tonight.~~ unfortunately my mini beta board is on a version that doesn't support sensorless homing yet and won't be updated anymore. But downstream I see your problem with sensorless homing was fixed, so yay!

Veti

@Alucardi said in Duet 3 mini 5+ sensorless homing will not work:

I believe it to be firmware though since even if downloading 3.2 firmware we are stuck on beta, Wonder why they don’t fix that

if you are on the beta, then stall detection is not implemented

to update see
https://forum.duet3d.com/topic/20382/unable-to-update-firmware-on-duet-mini-5-ethernet

jay_s_uk

TBH, I couldn't get mine to stall with a simple movement with S set to -64 either.

Alucardi

@Veti why is this not fixed in the stable release?