-
I'm having trouble getting my probe to show up. I tried analog and digital. I'm not sure what I'm doing wrong but the probe doesn't even show up anymore.
I'm using this probe: https://www.amazon.com/gp/product/B07V6GR72Q/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
; Configuration file for Duet WiFi (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.1.4 on Sun Nov 08 2020 20:39:44 GMT-0500 (EST) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Sauron" ; set printer name M665 R217.8 L118.7 B70 H280 ; Set delta radius, diagonal rod length, printable radius and homed height M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S1 D3 ; physical drive 0 goes forwards M569 P1 S1 D3 ; physical drive 1 goes forwards M569 P2 S1 D3 ; physical drive 2 goes forwards M569 P3 S1 D3 ; physical drive 3 goes forwards M569 P4 S0 D2 ; physical drive 4 goes forwards M584 X0 Y1 Z2 E4:3 ; set drive mapping M350 X16 Y16 Z16 E16:16 I1 ; configure microstepping with interpolation M92 X80.00 Y80.00 Z80.00 E823.00:823.00 ; set steps per mm M566 X1200.00 Y1200.00 Z1200.00 E1200.00:1200.00 ; set maximum instantaneous speed changes (mm/min) M203 X18000.00 Y18000.00 Z18000.00 E1200.00:1200.00 ; set maximum speeds (mm/min) M201 X3000.00 Y3000.00 Z3000.00 E1000.00:1000.00 ; set accelerations (mm/s^2) M906 X800 Y800 Z800 E800:800 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 Z0 S1 ; set minimum Z M591 P1 C"e0det" D0 S1 ; filament run out sensor M591 P2 C"!e1det" D1 S1 ; filament run out sensor ; Endstops M574 X2 S1 P"xstop" ; configure active-high endstop for high end on X via pin xstop M574 Y2 S1 P"ystop" ; configure active-high endstop for high end on Y via pin ystop M574 Z2 S1 P"zstop" ; configure active-high endstop for high end on Z via pin zstop ; Z-Probe M558 P8 C"!zprobe.in" R0.8 F300 ; set Z probe type to switch and the dive height + speeds G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height M557 R70 S20 ; define mesh grid ; Heaters M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bed" T0 ; create bed heater output on bedheat and map it to sensor 0 M307 H0 A174.1 C624.2 D0.3 S1.00 V0.0 B0 ; disable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M143 H0 S90 ; set temperature limit for heater 0 to 90C M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M307 H1 A518.8 C179.5 D4.1 S1.00 V0.0 B0 ; disable bang-bang mode for heater and set PWM limit ; Fans M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off M950 F1 C"HE1" Q500 M106 P1 S0.75 H-1 ; Tools M563 P0 S"left spool" D0 H1 F0 ; define tool 0 M563 P1 S"right spool" D1 H1 F0 ; define tool 1 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C ; Custom settings are not defined M307 H1 A518.8 C179.5 D4.1 S1.00 V0.0 ; hotend PID tune M307 H0 A174.1 C624.2 D0.3 S1.00 V0.0 ; bed PID tune M575 P1 S3 B57600 ; display comms -
How do you have it wired up?
Did it work at all? What do you mean that it doesn't show up anymore?
-
It's embarrassingly simple. the pin name on my board, an skr 1.4T, was actually just "probe"
-
So this is on an SKR board? You're not giving me a lot to work with here.
-
Yes, an SKR 1.4 turbo. It sees the probe now that I changed the pin name, but now it won't home. It looses position once I run the home command and won't move except to rehome. After homing, the positions are n/a.
-
this thread should be moved to the lpc category
post your homedelta.g script.
-
@Veti said in Piezo probe not seen SKR 1.4 RRF3:
this thread should be moved to the lpc category
Moved.
