Problems with steppermotor
-
Also with one Firmware i was able to move one motor but since i change something nothing will work anymore
-
please post your config.g and your homing files
-
Config :
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun Feb 09 2020 12:48:51 GMT+0100 (Mitteleuropäische Normalzeit); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Anet E12" ; set printer name; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z1400 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X310 Y310 Z400 S0 ; set axis maxima; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop; Z-Probe
M558 P1 C"zprobe.in+zprobe.mod" H5 F120 T18000 ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 X15:215 Y15:195 S20 ; define mesh grid; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings are not defined
; Miscellaneous
M501 ; load saved parameters from non-volatile memoryHoming:
; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun Feb 09 2020 12:48:51 GMT+0100 (Mitteleuropäische Normalzeit)
G91 ; relative positioning
G1 H2 Z5 F18000 ; lift Z relative to current position
G1 H1 X-315 Y-315 F1200 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F18000 ; go back a few mm
G1 H1 X-315 Y-315 F360 ; move slowly to X and Y axis endstops once more (second pass)
G1 H1 Z-405 F360 ; move Z down stopping at the endstop
G90 ; absolute positioning
G92 Z0 ; set Z position to axis minimum (you may want to adjust this); Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F300 ; lift Z relative to current position
;G90 ; absolute positioning -
duble check your wires, did you get some error messages in the console if you try to home your printer ?
-
Most likely you don't have the stepper motor wires correctly phased (CAUTION: this can damage the drivers!), or there is a bad connection in one wire.
-
I think all wires a correct connectet. in other orientations the stepper does nothing at all. And then i get a error message, but not when the stepper stutters
is there a way to check if the drivers a damaged?
-
@MauriceM said in Problems with steppermotor:
M584 X0 Y1 Z2 E3 ; set drive mapping
you can swap the drivers change the wiring lets say swap x and y and add M584 X1 Y0 Z2 E3 ; set drive mapping and try again.
-
So i achieved that all motors turn except the z motors
It was a cable Problem, i hope i didnt demaged the z drivers
-
Thanks Guys, now it works , i bought cables with different colour matching. Was a stupid mistake but i damaged nothing and now i can enjoy my silent printer.
-
@MauriceM, I'm glad it all worked out for you and didn't cause any damage. Unfortunately, for stepper motors that have 6-pin JST connectors on them, there are at least 2 different pinouts used. So you can't rely on the wire colours being correct, especially if the motors and cables were purchased for different suppliers.
Can you tell us what VIN voltage you used, and what type of motors? Did you get any "short to ground" warnings from the firmware? I'd like to get a better idea of when the internal short circuit protection in the drivers works.
-
VIN in 12.5V and the type of Motor is: 42SHDC3025-24B.
But i never had a short to ground issue.
