CR-10S5 Firmware

Veti

Lines are becoming to small and separating multiple times in one movement.

is your thermistor set up correctly? are your e steps set up correctly?

Gost101

@Veti Yes they are, just got back to my benchy test print ive been gone for almost 6 hours and cura said that it was a 3 hour print. Turns out the printer is not fast still. What should do?

Gost101

Veti

did you restart the printer after you made those changes? anytime you are printing an old file you will revert the settings and need to reboot.

PaulHew

FYI I think the start code Veti is referring to is in your slicer.
If it is Cura.
Settings - Printers - manage printers
Select your printer and click 'Machine Settings'

On that page at the bottom there is a window with Start G-Code

Remove the lines you have been asked to remove.
M201 X500.00 Y500.00 Z100.00 E5000.00 ;Setup machine max acceleration
M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate
M204 P500.00 R1000.00 T500.00 ;Setup Print/Retract/Travel acceleration
M205 X8.00 Y8.00 Z0.40 E5.00 ;Setup Jerk

HTH
Paul.

Phaedrux

@Gost101 said in CR-10S5 Firmware:

M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate

Your screen shot shows the top speed as 8.4mm/s which is basically 500mm/min. So I think you still haven't removed the limiting start gcode from cura. Follow the directions that @PaulHew has given.

Once that change is made it will only apply to newly sliced files. All your previously sliced files will have the slow limits set.

Gost101

@Veti I did reboot it. I did find that in cura and deleted it. lol

Gost101

@Phaedrux @PaulHew @Veti Great confusion this printer has caused me, yet more to learn I must. Sorry I have been watching to much star wars. lol.

Gost101

START

M220 S100 ;Reset Feedrate
M221 S100 ;Reset Flowrate

G28 ;Home

G92 E0 ;Reset Extruder
G1 Z2.0 F3000 ;Move Z Axis up
G1 X10.1 Y20 Z0.28 F5000.0 ;Move to start position
G1 X10.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line
G1 X10.4 Y200.0 Z0.28 F5000.0 ;Move to side a little
G1 X10.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line
G92 E0 ;Reset Extruder
G1 Z2.0 F3000 ;Move Z Axis up

STOP

G91 ;Relative positioning
G1 E-2 F2700 ;Retract a bit
G1 E-2 Z0.2 F2400 ;Retract and raise Z
G1 X5 Y5 F3000 ;Wipe out
G1 Z10 ;Raise Z more
G90 ;Absolute positionning

G1 X0 Y{machine_depth} ;Present print
M106 S0 ;Turn-off fan
M104 S0 ;Turn-off hotend
M140 S0 ;Turn-off bed

M84 X Y E ;Disable all steppers but Z

Phaedrux

And what speeds are set in cura for printing moves?

Gost101

@Phaedrux For this profile it is:

Gost101

@Phaedrux Regardless of any adjustments to this, it still takes a long time to print. Even after the changes made.

Phaedrux

Can you post a gcode file somewhere for us to see? And perhaps your current config.g file as it is right now?

Gost101

Heres the benchy file: Benchy GCode

;config.g
; Created by Gost101 on Saturday, September 28th, 2019 at 18:00 (6:00PM for Civs). 
; This firmware discussion can be found on duet fourm: https://forum.duet3d.com/topic/11964/cr-10s5-firmware/37
; Contact gost1017@gmail.com for more help.

; General preferences
G90                                        ; send absolute coordinates...
M83                                        ; ...but relative extruder moves
M550 P"A.C.E."                             ; set printer name
M669 K0                                    ; select Cartesian mode

; Network
M551 P"SpaceForceHu2020!!"                 ; set password
M552 S1                                    ; enable network
M586 P0 S1                                 ; enable HTTP
M586 P1 S0                                 ; disable FTP
M586 P2 S0                                 ; disable Telnet

; Drives
M569 P0 S1                                 ; X physical drive 0 goes forwards
M569 P1 S1                                 ; Y physical drive 1 goes forwards
M569 P2 S0                                 ; Z physical drive 2 goes backwards
M569 P2 S0                                 ; Z physical drive 2 goes backwards
M569 P3 S0                                 ; E physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                           ; set drive mapping
M350 X16 Y16 Z16 E16 I1                    ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E408.30          ; set steps per mm
M566 X500.00 Y500.00 Z30.00 E1500.00      ; set maximum instantaneous speed changes (mm/min)
M203 X10800.00 Y9000.00 Z300.00 E3000.00   ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z500.00 E3000.00      ; set accelerations (mm/s^2)
M906 X950 Y950 Z850 E900 I30              ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                    ; Set idle timeout

; Axis Limits
M208 X0:500 Y0:500 Z0:500                  ; set axis maxima

; Endstops
M574 X1 Y1 Z1 S1                           ; set active high endstops

; Z-Probe
M558 P0 H5 F120 T6000                      ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20                   ; define mesh grid

; Heaters
M305 P0 T100000 B3950 R4700                ; set thermistor + ADC parameters for the heated bed
M143 H0 S120                               ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4725 C7.060000e-8 R4700   ; set thermistor + ADC parameters for heater 1
M143 H1 S550                               ; set temperature limit for heater 1 to 550C

; Fans
M106 P0 S0 I0 F500 H-1                     ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45                  ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                           ; define tool 0
G10 P0 X0 Y0 Z0                            ; set tool 0 axis offsets
G10 P0 R0 S40                              ; set initial tool 0 active and standby temperatures to 40C

; Custom settings are not defined

Phaedrux

Cura has the option for having the first couple layers after the first layer slowly ramping up to full speed. Have you done a full print yet to see if it speeds up? It also has a minimum layer time option which will slow down the print speed to allow for extra cooling time.

Would it be possible for you to export your cura print settings so we could see the full settings?

Do you have another slicer configured to test against? PrusaSlicer perhaps?

Gost101

@Phaedrux Part of a print, no where near the time of completion it was supposed to be. Sure, here is the Print Settings. I don't have another slicer. Big Rips. Also my cura dosent seem to want to work anymore. It wont launch and I have to reinstall it everytime in order to launch it. I have done a complete un-install as well and this still persists. I keep my congfig files saved.

Veti

first of disable tree support. you dont need that for benchy

your inner wall settings is 20mm/sec
;TYPE:WALL-INNER
G1 F1200 X252.085 Y243.08 E0.9276

Phaedrux

@Gost101 said in CR-10S5 Firmware:

It wont launch and I have to reinstall it everytime in order to launch it.

If you're on windows you will need to go to %appdata% and rename the cura folder there and then reinstall cura. You may need to re-create your printer and print settings, but it should work properly afterwards.

Veti

;SETTING_3 {"extruder_quality": ["[general]\nversion = 4\nname = Super Quality
;SETTING_3 #2\ndefinition = creality_cr10s5\n\n[metadata]\nquality_type = s
;SETTING_3 uper\ntype = quality_changes\nposition = 0\nintent_category = defa
;SETTING_3 ult\nsetting_version = 10\n\n[values]\nbuild_volume_temperature =
;SETTING_3 10\ncoasting_enable = True\ncoasting_volume = 0.4\ndefault_materi
;SETTING_3 al_print_temperature = 210\nfill_outline_gaps = True\ninfill_multip
;SETTING_3 lier = 1\ninfill_overlap = 0\ninfill_pattern = triangles\ninfill_s
;SETTING_3 parse_density = 5\nironing_enabled = True\nlimit_support_retraction
;SETTING_3 s = False\nmaterial_final_print_temperature = 210\nmaterial_initial
;SETTING_3 print_temperature = 210\noptimize_wall_printing_order = True\nretr
;SETTING_3 act_at_layer_change = True\nretraction_amount = 10\nretraction_coun
;SETTING_3 t_max = 0\nretraction_extra_prime_amount = 0\nretraction_extrusion
;SETTING_3 window = 3\nretraction_hop_enabled = True\nretraction_min_travel =
;SETTING_3 0.7\nretraction_prime_speed = 1\nroofing_layer_count = 3\nspeed_pr
;SETTING_3 int = 100\nsupport_angle = 80\nsupport_infill_rate = 5\nsupport_in
;SETTING_3 terface_density = 15\nsupport_interface_height = 1\nsupport_interfa
;SETTING_3 ce_pattern = zigzag\nsupport_interface_skip_height = 1\nsupport_lin
;SETTING_3 e_distance = 5\nsupport_use_towers = True\nswitch_extruder_retracti
;SETTING_3 on_amount = 0\nswitch_extruder_retraction_speeds = 40\ntop_bottom_t
;SETTING_3 hickness = 3\nz_seam_corner = z_seam_corner_inner\nz_seam_type = sh
;SETTING_3 arpest_corner\nzig_zaggify_infill = True\n\n"], "global_quality":
;SETTING_3 "[general]\nversion = 4\nname = Super Quality #2\ndefinition = cre
;SETTING_3 ality_cr10s5\n\n[metadata]\nquality_type = super\ntype = quality_
;SETTING_3 changes\nintent_category = default\nsetting_version = 10\n\n[valu
;SETTING_3 es]\nacceleration_enabled = False\nadhesion_type = raft\ndefault_m
;SETTING_3 aterial_bed_temperature = 50\nflow_rate_extrusion_offset_factor = 95
;SETTING_3 \nflow_rate_max_extrusion_offset = 5\nretraction_combing = off\nsu
;SETTING_3 pport_enable = True\nsupport_type = buildplate\n\n"}

retraction_hop_enabled = True
you might want to disable that.

Gost101

@Phaedrux Thanks, that just fixed cura not opening. Cool beans, @Veti don't know why I had tree support turned on. Lol.