Fan settings not working
-
I am wanting to change fan speed according to layer. I have it set up in cura to do this but it doesnt happen when printing. I end up having to change it manually with the slider. Do I have something setup wrong? In the web portal for the printer it also shows three fans which I only have 2. It shows 'Tool Fan' being a fan along with 'Hotend' and 'Blower'
; Configuration file for Duet WiFi (firmware version 1.21) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2 on Wed Apr 17 2019 17:42:43 GMT-0400 (Eastern Daylight Time) ; General preferences G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves ; Network M550 P"Ender3" ; Set machine name M586 P0 S1 ; Enable HTTP M586 P1 S0 ; Disable FTP M586 P2 S0 ; Disable Telnet ; Drives M569 P0 S0 ; Drive 0 goes backwards M569 P1 S0 ; Drive 1 goes backwards M569 P2 S1 ; Drive 2 goes forwards M569 P3 S0 ; Drive 3 goes backwards M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation M92 X80.00 Y80.00 Z400.00 E106.29 ; Set steps per mm M566 X600.00 Y600.00 Z24.00 E300.00 ; Set maximum instantaneous speed changes (mm/min) If bad prints change to 600 M203 X30000.00 Y30000.00 Z800.00 E1500.00 ; Set maximum speeds (mm/min) M201 X500.00 Y500.00 Z100.00 E5000.00 ; Set accelerations (mm/s^2) M906 X500.00 Y500.00 Z500.00 E500.00 I30 ; Set motor currents (mA) and motor idle factor in per cent M84 S300 ; Set idle timeout ; Axis Limits M208 X-5.5 Y-10 Z0 S1 ; Set axis minima M208 X243 Y231 Z260 S0 ; Set axis maxima ; Endstops M574 X1 Y1 S1 ; Set active high endstops ; Z-Probe M574 Z1 S2 ; Set endstops controlled by probe M307 H3 A-1 C-1 D-1 ; Disable heater on PWM channel for BLTouch M558 P9 H5.0 F120 T6000 ; Set Z probe type to bltouch and the dive height + speeds G31 P25 X-40 Y0 Z1.78 ; Set Z probe trigger value, offset and trigger height M557 X50:185 Y50:185 S65 ; Define mesh grid ; Heaters M305 P0 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 0 M143 H0 S120 ; Set temperature limit for heater 0 to 120C M305 P1 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 1 M143 H1 S280 ; Set temperature limit for heater 1 to 280C ; Fans M106 P2 S1 I0 F10 H-1 C"Blower" ; Set fan 0 value, PWM signal inversion and frequency. M106 P1 S.5 I0 F500 H-1 C"Hotend" ; Set fan 1 value, PWM signal inversion and frequency. ; Tools M563 P0 D0 H1 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C ; Automatic power saving M911 S10 R11 P"M911 S10 R11 P""M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss ; Custom settings are not configured ; Miscellaneous ;M501 ; Load saved parameters from non-volatile memory
-
Well I think I know the issue. Cura cannot address fans. Being that my blower is P2 and not the default P0 the gcode command being sent wont work. So I think I need to rename my blower fan to P0 in order to get this to work. Well never mind, Seems pwm is not working on fan_0. A bit upsetting.
Is there any way to remap fan_2 and make it fan_0?
-
@jtroutt19 said in Fan settings not working:
Is there any way to remap fan_2 and make it fan_0?
There are two ways. You can use RepRapFirmware 3 which allows you to map any fan number to any suitable output pin. Or you can use the F parameter in the M563 commands that you use to create tools, to specify which fan is the default print cooling fan for each tool.