Hotend temperature rising too "slowly" except it isnt.
-
Have you run heater auto tuning yet? See https://duet3d.com/wiki/Tuning_the_heater_temperature_control.
-
no never tuned, didnt know I could, will have a go
-
So my initial settings are,
===========
6:40:19 AM
M303
Heater 1 is being tuned, phase 3 of 3
6:34:48 AM
M303 H1 P0.5 S260
Auto tuning heater 1 - do not leave printer unattended
6:29:59 AM
M303
No heater has been tuned yet
6:24:45 AM
M307 H1
Heater 1 model: gain 340.0, time constant 140.0, dead time 5.5, max PWM 1.00, in use: yes, mode: PID
Setpoint change: P13.4, I0.10, D51.4
Load change: P13.4, I0.95, D51.4I set 260C as the upper limit, M303 H1 P0.5 S260 and it tripped at 260C
What temperature is the tuning meant to go to? kind of wondering as with the wanhao board firmware originally you told it the set point you wanted.
The heating curve is totally different running this, its way steeper and its convex as opposed to concave….
-
A hole in the wiki,
https://duet3d.com/wiki/Spurious_heater_faults_and_how_to_avoid_them
points me at,
https://duet3d.com/wiki/Tuning_the_heat
"Tuning the heat
There is currently no text in this page. You can search for this page title in other pages, or search the related logs, but you do not have permission to create this page.
" -
Re-trying P=0.25. painfully slooooow
-
Uh,
============
7:15:49 AM
M307 H1
Heater 1 model: gain 626.6, time constant 265.6, dead time 13.9, max PWM 1.00, in use: yes, mode: PID
Setpoint change: P5.5, I0.02, D53.0
Load change: P5.5, I0.17, D53.0
7:14:46 AM
Warning: Heater 1 appears to be over-powered and a fire risk! If left on at full power, its temperature is predicted to reach 646C.
Auto tune heater 1 with PWM=0.25 completed in 774 sec, maximum temperature reached 178.6C
Use M307 H1 to see the result
7:14:43 AM
M303
Heater 1 is being tuned, phase 3 of 3?
-
From what I read I now have new PID settings? its all auto set?
========
7:18:21 AM
M303
Heater 1 tuning succeeded, use M307 H1 to see resultI guess so?
Too big a heater is a concern? most odd.
-
You now add a M307 H1 line to config.g with the settings M303 found.
M307 H1 A626.6 C265.6 D13.9 ; hotend pid settings
The too big heater warning is there to alert you what temp it can reach if it gets stuck on. In normal use, you shouldn't have a problem.
-
With firmware 1.17 you can run M500 to write the M307 commands to config-override.g.
-
Thanks but I dont feel brave enough to try updating my firmware yet. I might just leave it until Ive bought a second duetwifi in a month or two so I am not left stuck in the poo if something goes wrong. New ones will come with 1.17 anyway?
I have not tried running the 3d printer yet to see if its OK as I did this before I left for work this morning and wanted it stone cold before I did as it only seemed to trip at 50~60C or so, once above 100~120C it goes up faster and never trips.
"normal use" yeah having read the horror stories, I have an arduino mega with a separate thermistor in the heater block (and one in the cold end block and one in the bed). The idea is if the arduino mega sees excessive temperature in either it will drop the SSR powering the d6 out. It got removed while removing the dead wanhao motherboard and installing the duetwifi so I need to put it all back in again. I also have an infra red sensor I want to play with.
-
Wow that is way way faster and it gets to 235C without any 5C+ overshoot and minute or 2 to settle like it did before
