Firmware(ahhhhhh) Gotta be an easier way!

aidar

@Styler93gsx said in Firmware(ahhhhhh) Gotta be an easier way!:

M552 S-0

This is not valid command, use M552 S0 to put wifi module to idle mode

Styler93gsx

@droftarts
I had it in idle mode last night for abou a few hours. I sent M997 S0 M997 S1 M552 M552 S1 M552 S0 M552 more times than I can count and not all it that particular order. I really think my M key on my keyboard is about worn out. I've pulled my Micro SD card and formatted, copy pasted, watched numerous youtube videos and have read on the WIKI till I started seeing double. Took a three hour nap an only think I can say that has gone right is after the three hour nap I"m not seeing double anymore.

I've explored fallback firmware #1 #2 & #3

#3 I even started with a different freshly formatted SD card and still can't get he 1.02 to update to anything other than 1.02

When I send M115 I get
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.03 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2019-06-13b2

I have uploaded firmwares 2.05RC all the way down to 2.03. But it always says Duet Wifi 1.02

If that 1.02 is referring to my board then how do I actually check my wifi server bin version
When I send M122 This is what I get.

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03 running on Duet WiFi 1.02 or later
Board ID: 08DAM-9K9K2-NGNS0-7JKDL-3SJ6J-K70HL
Used output buffers: 1 of 24 (10 max)
=== RTOS ===
Static ram: 25680
Dynamic ram: 93636 of which 0 recycled
Exception stack ram used: 312
Never used ram: 11444
Tasks: NETWORK(ready,548) HEAT(blocked,1172) MAIN(running,3832) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 07:17:54 ago, cause: software
Last software reset at 2019-01-22 23:57, reason: User, spinning module GCodes, available RAM 5672 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 12.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 28.7, current 29.8, max 32.3
Supply voltage: min 0.5, current 0.5, max 0.6, under voltage events: 0, over voltage events: 0, power good: no
Driver 0: ok, SG min/max not available
Driver 1: ok, SG min/max not available
Driver 2: ok, SG min/max not available
Driver 3: ok, SG min/max not available
Driver 4: ok, SG min/max not available
Date/time: 1970-01-01 00:00:00
Cache data hit count 4294967295
Slowest loop: 99.59ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 0.20ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8

WiFi -
Network state is starting
WiFi module is disabled
Failed messages: pending 0, notready 0, noresp 0
Socket states: 0 0 0 0 0 0 0 0
ok

Styler93gsx

@aidar
If is not a valid command why does it say OK?

I've tried it with M552 S0 and M552 S-0

Both respond with ok.

The part that you read up above I copy and pasted the entire dialog and as you can see when I typed M552 S-0 it responded with ok.

I've tried M552 I don't know how many times and at one point it was saying the wifi module is idle but now it just keeps saying wifi module is starting.

Danal

@Styler93gsx said in Firmware(ahhhhhh) Gotta be an easier way!:

#3 I even started with a different freshly formatted SD card and still can't get he 1.02 to update to anything other than 1.02

When I send M115 I get
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.03 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2019-06-13b2

2.03 is your firmware version and 2019-06-13b2 is the date of that firmware version's build.

FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.03 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2019-06-13b2

1.02 is your 'electronics'. That is, the board. The hardware. It will NEVER change (unless you buy new/different hardware).

Danal

@Styler93gsx said in Firmware(ahhhhhh) Gotta be an easier way!:

@aidar
If is not a valid command why does it say OK?

I've tried it with M552 S0 and M552 S-0

Both respond with ok.

The part that you read up above I copy and pasted the entire dialog and as you can see when I typed M552 S-0 it responded with ok.

I've tried M552 I don't know how many times and at one point it was saying the wifi module is idle but now it just keeps saying wifi module is starting.

It might say OK, but S-0 is not the documented format of the command and none of us can have any idea what S-0 does (or does not) do. For now, please stick to S0 for idle.

Danal

And, a couple of notes:

The erase button on the main board erases the flash memory in the CPU of the main board. It does NOT erase the WiFi module. There is no way to erase WiFi; instead, overwrite it.
When executing the various recovery options, your SD should look like:

sys/Duet2CombinedFirmware.bin
sys/iap4e.bin
sys/DuetWiFiServer.bin
www/ (will look more or less like screenshot below)

Connect with YAT (or other terminal) and issue:

M997 S0:1

This updates BOTH the main board and the WiFi together. That is more likely to work. If for some reason it does not, you can try M997 S0 and M997 S1 separately.

At that point, you should have good firmware. From there, you should be able to get on your network via:

https://duet3d.dozuki.com/Guide/1.)+Getting+Connected+to+your+Duet/7

droftarts

@Styler93gsx

M552 S-1 turns the WiFi module off. M552 S0 turns it on, and sets it to idle mode. M552 S1 activates it to connect to any WiFi access point that it has been configured to connect to. I'm guessing M552 S-0 is interpreted as S0.

As @Danal says, your firmware version is 2.0.3. Your Duet board revision is 1.0.2. I expect you are continuously updating the board with the same firmware version, 2.0.3. Try this one instead: https://github.com/dc42/RepRapFirmware/releases/tag/2.04

Ian

zapta

@droftarts said in Firmware(ahhhhhh) Gotta be an easier way!:

Try this one instead: https://github.com/dc42/RepRapFirmware/releases/tag/2.04

I find the firmware release more confusing than needed, having to sift through a list of files, most of them non relevant to majority of the users. Could be simplified along these lines:

Duet2 Wifi

board_firmware_xyz.zip
panel_due_xyz.zip

Maestro

(similar)

And a link to a repository where the developer oriented files can be found.

Styler93gsx

Ok I have 2.04 installed and Wifi Module is going into idle again. But I'm still getting Errror retrieving Wifi status message: SPI timout.

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.04 running on Duet WiFi 1.02 or later
Board ID: 08DAM-9K9K2-NGNS0-7JKDL-3SJ6J-K70HL
Used output buffers: 1 of 24 (1 max)
=== RTOS ===
Static ram: 25680
Dynamic ram: 92696 of which 0 recycled
Exception stack ram used: 288
Never used ram: 12408
Tasks: NETWORK(ready,1280) HEAT(blocked,1208) MAIN(running,3808) IDLE(ready,200)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:02:07 ago, cause: software
Last software reset time unknown, reason: User, spinning module GCodes, available RAM 11444 bytes (slot 2)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x04433000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 12.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 29.2, current 30.6, max 30.8
Supply voltage: min 0.4, current 0.5, max 0.6, under voltage events: 0, over voltage events: 0, power good: no
Driver 0: ok, SG min/max not available
Driver 1: ok, SG min/max not available
Driver 2: ok, SG min/max not available
Driver 3: ok, SG min/max not available
Driver 4: ok, SG min/max not available
Date/time: 1970-01-01 00:00:00
Cache data hit count 808438268
Slowest loop: 392.09ms; fastest: 0.05ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 160, MinFreeDm: 160, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 401.11ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8

WiFi -
Network state is running
WiFi module is idle
Failed messages: pending 0, notready 0, noresp 471
Error retrieving WiFi status message: SPI timeout
Failed to get WiFi status
Socket states: 0 0 0 0 0 0 0 0
ok