Posts made by Woody78

@droftarts yes i know. i have only the connection problem in my last connector on the hotend...

@droftarts do you know if i can measure the 3.3v every time or only when the board gives a signal?

@droftarts okay, i checked another led strip in spare directly on the board without level shifter. it worked fine. so i have to check my wires to the stealthburner, i hope it is no problem that the wires are over 2m long

@droftarts i´d tried your config with and without level shifter. but nothing happend... i don´t know why...
it is possible to test the led´s on another way... to check?

Re: 3.5.0-beta.4 neopixel on duet 2 wifi

hi there, i have installed my stealthburner with 3 LEDs neopixel 5V version.
I have also a logic level shifter between board and leds, but nothing happend.
when i measuring on the pins i have all about 4.95V, i think it is okay...

in my config.g i have:

M950 E0 T1 C"connlcd.5" U3
M150 E0 X3 Q3000000
M150 E0 R255 P255

the pins on the board i used are:

5V = 1)5V CONN_SD
GND = 2)GND CONN_SD
3.3V = 5) En10 (LCD_DB7) CONN_LCD

the 5V and GND goes direct to LEDs and HighInput of LLC and the 3.3V DataLine goes to LowInput LLC

@jay_s_uk okay, thanks thats easy to make.

Hi there,

i´m using Duet 2 Wifi FW 3.5.3 on my hypercube setup.
now when i home x axis (i drive first z a little bit down) become a warning: Driver 2 warning: phase B may be disconnected
the bed doesn´t move and it´s very load on the z steppers, they are shaking...
few hours ago it´s run normal. then i put the stepper out from the printer, change against other stepper, change back to the old stepper, and everything looks fine. i put the stepper back in the printer, and then works.
after few hours with power off from the printer, i want to test something, first start G28 X and same again.

i don´t know what can i do....

@cosmowave thats great. many thanks

Hi there, i didn´t find anything to make a own new button in DWC to start for example a macro.
It is generally possible?

@chrishamm yes, it is. great. thank you... now everything is fine

Hello,
after Update to 3.5.3 on my duet 2 wifi at every start it gives me this error message:

Bad command: Configuration file for Duet WiFi (firmware version 3.3)

my installation is:

Duet 2 WiFi 2WiFi 3.5.3
Duet WiFi Server n/v 2.1.0
Duet Web Control DWC 3.5.3

what can i do?

Hallo, ich möchte meinen Hypercube mit einer Klicky PCB ausstatten und stehe vor der Frage wie ich diesen an das Duet 2 anschließen muss. Es gibt ja den Anschluss für Z-Probe und den regulären Endstop Z Anschluss. Der Klicky müsste ja eigentlich nur als einfacher Schalter arbeiten, sprich er schaltet die angelegte Spannung bzw. GND.
Für die spätere Programmierung ist es sicherlich wichtig zu wissen ob der Klicky an den Z-Probe gehört oder an den Endstop Eingang. Hat jemand eine Idee?

Hello, I would like to equip my Hypercube with a Klicky PCB and am wondering how to connect it to the Duet 2. There is the connection for the Z-Probe and the regular Endstop Z connection. The Klicky should actually only work as a simple switch, i.e. it switches the applied voltage or GND. For later programming it is certainly important to know whether the Klicky belongs to the Z-Probe or the Endstop input. Does anyone have any ideas?