@fcwilt No I didn't, I made sure.
Best posts made by TRATOON
-
RE: Duet 2 Fans No Longer Work
-
RE: Filament sensor constantly throws errors
@infiniteloop Thank you, I had already tried LoFi's design a few days ago, just had to file it down and tweak it a little, now it works like a charm.
-
RE: Prints are warping
@alankilian OK, thank you I will go pick up the PEI plate from Microcenter today and let you know if it works.
-
RE: Prints are warping
@engikeneer Thank you very much, that solved my problem
Latest posts made by TRATOON
-
RE: Connecting a specific Accelerometer to Duet 2 Wifi
@tas Could you post your wiring on both accelerometer and Duet and also what are you using for accelerometer for? Input shaping? If so, do you know if the Duet takes live input from the accelerometer and changes input shaping for each movement, also do you notice a significant improvement in print quality? Also, what is the boards orientation and what is your I value (for input shaping if you are using it, as mentioned here https://docs.duet3d.com/User_manual/Connecting_hardware/Sensors_Accelerometer)
-
Connecting a specific Accelerometer to Duet 2 Wifi
Hello, I plan on installing this accelerometer to my 3D printer with a Duet 2 Wifi. I was wondering if this specific one would work and if it would be possible to use the in-built temp sensor and if the DSH version is worth it compared to sparkfuns DH, I plan on using it for input shaping. Also, in the docs, a ribbon cable is used, however, I though ribbon cables can really only be used for short distances and I have a Ender 5 Plus (500mm^2) and if there is any way to get around that.
-
RE: Rough print finish and dimensional inaccuracy
@mrehorstdmd How tight should the belts be I'm using exoslide so I will reach out to him to see if any of the exoslide parts can cause this problem, also what are some areas where wobble might be common?
-
RE: Rough print finish and dimensional inaccuracy
@mrehorstdmd I just finish printing my part with a .2mm layer and .3mm for initial layer with a .4 nozzle and line width of .4. I also added the motor line as @gloomyandy pointed out and reset my steps for motors to 80,80,800. Now, my print quality is better, but there are still some ridges however I noticed they only occur on the left side of the x axis (facing printer from front). The corner thing is still mildly present and then there are these lines on the surface of print (circled). The face of the part in the image you can see was printed in the back of the printer. I calibrated only E-Steps, should I calibrate flow as well?
-
RE: Rough print finish and dimensional inaccuracy
@mrehorstdmd No it is just 800m/s no upstepping. So you are saying I set it back to 800m/s and I will be fine printing at 0.2 mm and 0.35mm as both of those are divisible evenly by 1.25um?
-
RE: Rough print finish and dimensional inaccuracy
@mrehorstdmd I am was using 10000mm/s/s for acceleration in cura and 80mm/s for speed but I reduced it to 2750 for acceleration and 60mm/s for speed and I saw a little improvement. iam nost sure what pressure advance is.
-
RE: Rough print finish and dimensional inaccuracy
@mrehorstdmd What is step multiples for layer thickness? What layer height should I be using for 80,80,800?
-
RE: Rough print finish and dimensional inaccuracy
@gloomyandy Yes the values are supposed to be 80,80,800. However, I thought it was common practice to calibrate these values which is how I reached these values.
-
RE: Rough print finish and dimensional inaccuracy
@mrehorstdmd My layer height is 0.2 mm and 0.3 mm for first layer.