Posts made by TNC

My initial pursuit was a Ballscrew Core XY machine; configuration
proved different. Currently using Cartesian configuration files.
What configuration files should I be using???

@phaedrux
https://share.icloud.com/photos/0KhsV-vT1zNMIi8HbYeDvEJZg
Before reading the above documentation I made it to this point.
Thanks for putting me back on track!!!

@droftarts
https://share.icloud.com/photos/0KhsV-vT1zNMIi8HbYeDvEJZg
That's 100mm/s!!!
Didn't understand Expansion Board page in RRF Config. tool. HELP PLEASE!!!

@o_lampe
https://share.icloud.com/photos/0KhsV-vT1zNMIi8HbYeDvEJZg
That's 100mm/s!!!
Didn't understand Expansion Board page in RRF Config. tool. HELP PLEASE!!!

I need help setting up my Duex 5 board w/ Duet WiFi; pictured is the build. Unsuccessful w/RRF Config. tool
on Expansion board page. The link below is the ambitious project.
https://a360.co/3av4BEB
Ballscrews utilized for movement; marginal success with Cartesian
setup in RRF tool. Homing, movement, speeds...etc
Where do I begin???

@phaedrux
Hey Phaedrux, re-flash worked; got an IP address/DWC. I'm learning. Til next time,

     **THANKS!!!**

@paulhew
Hey Paul, thanks for responding. The move backwards was a start from the beginning attempt. Could've made a better decision!!! First of all, I'm currently using a Mac Book Pro (not very familiar) and I'm not very computer savvy. Couldn't get BOSSA to work with Big Sur (Mac); gonna try Windows. Do I simply copy/paste v3 RC into browser
and (write)???

I've lost connectivity with DWC after reverting from 3.2.2 back to 2.05: can't get IP address with M587 command in Serial Tool. Where did I go Wrong? Wifi module (blue) LED lit. TNC400 2.4Ghz Network.

@phaedrux

Thanks. I'm on it!!! Question: What bearing will non-upgrade of config.g
after 2.05 to 3.0 RRF have. Can those file changes be done in 3.2.2 RRF?

@phaedrux
Not triggered
Triggered

Seems I have a wiring issue, Huh?
No movement w/G1 H1 X200 F600 in the Console.
Everything seems to work fine from dashboard, except
endstop and Error message below.
Warning: motor phase A may be disconnected reported by driver(s) 0 1
Warning: motor phase B may be disconnected reported by driver(s) 1
I'll revisit (X-drive) termination @board. Error follows termination point.

@Phaedrux

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Sun Apr 18 2021 08:29:17 GMT-0400 (EDT)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-405 Y-405 F1800 ; move quickly to X or Y endstop and stop there (first pass)
G1 H1 X-405 ; home X axis
G1 H1 Y-405 ; home Y axis
G1 X5 Y5 F6000 ; go back a few mm
G1 H1 X-405 F360 ; move slowly to X axis endstop once more (second pass)
G1 H1 Y-405 ; then move slowly to Y axis endstop
G1 H1 Z-405 F360 ; move Z down stopping at the endstop
G90 ; absolute positioning
G92 Z0 ; set Z position to axis minimum (you may want to adjust this)
; homex.g
; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Sun Apr 18 2021 08:29:17 GMT-0400 (EDT)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-405 F1800 ; move quickly to X axis endstop and stop there (first pass)
G1 X5 F6000 ; go back a few mm
G1 H1 X-405 F360 ; move slowly to X axis endstop once more (second pass)
G1 H2 Z-5 F6000 ; lower Z again
G90 ; absolute positioning
; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Sun Apr 18 2021 08:29:17 GMT-0400 (EDT)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 Y-405 F1800 ; move quickly to Y axis endstop and stop there (first pass)
G1 Y5 F6000 ; go back a few mm
G1 H1 Y-405 F360 ; move slowly to Y axis endstop once more (second pass)
G1 H2 Z-5 F6000 ; lower Z again
G90 ; absolute positioning
; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Sun Apr 18 2021 08:29:17 GMT-0400 (EDT)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 Z-405 F1800 ; move Z down until the endstop is triggered
G92 Z0 ; set Z position to axis minimum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

I greatly appreciate your help with my situation!!!

@phaedrux generated by RepRapFirmware Configuration Tool v3.2.3 on Sun Apr 18 2021 08:29:16 GMT-0400 (EDT)
Why isn't Endstop working? config g. below; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Sun Apr 18 2021 08:29:16 GMT-0400 (EDT)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"TNC400" ; set printer name
M669 K1 ; select CoreXY mode

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X320.00 Y320.00 Z320.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X12000.00 Y12000.00 Z12000.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X950 Y950 Z950 E950 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X400 Y400 Z400 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop

; Z-Probe
M558 P5 C"^!zprobe.in" H5 F120 T6000 ; set Z probe type to switch and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 X15:215 Y15:195 S20 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

I inadvertently uploaded 3.2.2 firmware before updating config g. after 2.05 to 3.0
update. Ball screw motor not to responding to triggered Endstop.
Board: Duet 2 WiFi (2WiFi)
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.2.2 (2021-02-11)
Duet WiFi Server Version: 1.25