Posts made by tdybare69

I have 2 printers 1 X5S, and 1 X5SA both are setup the same only problem when i slice a stl file in cura. it prints perfect in the X5S, but does not scale correctly on X5SA. keeps giving me a message.
M32 "0:/gcodes/CFFFP_CR-10_HD-modular-mount-V6_mount-cover__40mm-fan_v1.gcode"
File 0:/gcodes/CFFFP_CR-10_HD-modular-mount-V6_mount-cover__40mm-fan_v1.gcode selected for printing
T0:23.1 /0.0 B:23.6 /70.0

@bearer yes. maybe the board had to warm up. got me stumped. i have come across weirder things than that unfortunately.

@droftarts finally got it to work. took sd card from working duet printer. ran a M21&M39, went to working.

@tdybare69 its new board. but i have had it for a while in box, stored safely. got it from matter hackers.

@tdybare69 i think your right. something has to be wrong with board.everything i try it still says none.

@bearer i think thts it . be right back gonna make sure there is no partitions. it says files none.

@bearer i went to github got the files you said,extracted it,and tried again. still says same thing. did M21 it says SDHC card mounted in slot 0, capacity 31.9GB<LF>ok<LF>
M39 says SDcard in slot 0: capacity 31.9GB, speed20.00MBytes/sec,cluster size 167kb<LF>ok<LF>

i replaced it with a working sdcard from other printer still no go. seems like board is not mounting sd card. is there a code i can use in yat to tell it to mount the card?

after enabling the wifi module, and entering the router setting when i go to the ip address it gives me i get a reject message

Your Duet rejected the HTTP request: page not found
Check that the SD card is mounted and has the correct files in its /www folder
please help.
could it be that i have a second printer running at the same time.

@bearer thank you

under voltage message
Resume state saved
Print auto-paused due to low voltage

Warning: VIN under-voltage event (9.2V)
this is what i got after i did a M122

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03 running on Duet WiFi 1.02 or later
Board ID: 08DGM-917DA-G4MS8-6JKDA-3SN6Q-TSV39
Used output buffers: 1 of 24 (6 max)
=== RTOS ===
Static ram: 25680
Dynamic ram: 93780 of which 280 recycled
Exception stack ram used: 628
Never used ram: 10704
Tasks: NETWORK(ready,660) HEAT(blocked,1236) MAIN(running,3820) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:08:16 ago, cause: power up
Last software reset time unknown, reason: User, spinning module GCodes, available RAM 10792 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 31.4, current 35.6, max 36.6
Supply voltage: min 12.0, current 12.1, max 12.2, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max 0/307
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2020-02-18 09:02:21
Cache data hit count 1820081411
Slowest loop: 3.99ms; fastest: 0.08ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 169, MinFreeDm: 166, MaxWait: 176ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 8, completed moves: 8, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.52ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8

• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.23
  WiFi MAC address ec:fa:bc:2d:dc:69
  WiFi Vcc 3.38, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 25752
  WiFi IP address 192.168.0.25
  WiFi signal strength -62dBm, reconnections 0, sleep mode modem
  Socket states: 0 0 0 0 0 0 0 0
  === Filament sensors ===
  Extruder 0 sensor: ok
  any ideas

@jens55 thank you

@zapta 14GA

this is what i recievedfor the M303 H0.
M307 H0
Heater 0 model: gain 317.3, time constant 665.7, dead time 9.8, max PWM 1.00, calibration voltage 12.1, mode PID, inverted no, frequency default
Computed PID parameters for setpoint change: P38.0, I0.470, D262.1
Computed PID parameters for load change: P38
M303 H1
PMM307 H1
Heater 1 model: gain 898.2, time constant 180.8, dead time 2.9, max PWM 1.00, calibration voltage 11.9, mode PID, inverted no, frequency default
Computed PID parameters for setpoint change: P12.4, I0.541, D25.2
Computed PID parameters for load change: P12.

i have hooked my duet2 wifi to my 12v powers supply,and 750w silcone bed via a ssr. how do i fine tune the heat bed in the config files?

heat bed seems to be losing temperature gradually. when i got it, it would reach 100 degrees, now it seems to only get up to 68.4. how can i test thermistor without just replacing it.

can the duet 2 wifi be hooked up to a 24v power supply. and if so what arrangements will i have to do for the bltouch

your right. i ran a gcode print on small item cut the filament. it worked. thank you

@tdybare69
sorry about the caps

@tdybare69 THIS IS WHT MY CODE LOOKS LIKE.
M591 D0 P1 C3 S1 ; sensor drive 0 is connected to EO endstop input, enabled, trigger M83