Posts made by Szurke

@ottobawt

I've got a similar problem, except none of my fans are working. I'm considering just getting a bunch of cheap 24v power supplies if I can't fix the fan headers.

Okay, I think I figured it out. In https://configtool.reprapfirmware.org/Endstops it doesn't automatically select Z-probe in the endstop type for the Z axis when you select BLTouch. When I did so, it seems to have solved my issue.

Hi, I didn't see any questions that answered my question but I would love to be wrong and pointed to the right page. Thanks for reading.

Here's the steps I followed, per
https://duet3d.dozuki.com/Wiki/Test_and_calibrate_the_Z_probe
and
https://betrue3d.dk/bltouch-on-duet-wifi-configuratio-and-usage/

Ender 3 (no Pro, no V2)
Duet 2 WiFi/Ethernet v1.04, firmware updated to 3.3
BLTouch V2.0
All wires are correct and seated
I edited the X and Y offset of the BLTouch to correspond to my mounting location.

(0) deployed sensor is about 2.5mm below nozzle
(1) deploy and retract work as normal
(2) dynamic test works
(3) I jog the nozzle down until it is just gripping a feeler gauge (0.10mm). During this step the BLTouch is triggered with Z-Probe value of 1000.
(4) G92 Z0
(5) Jog the head up 10mm. At this point I am unable to retract/deploy the probe.
(6) G30 S-1
     Error: Probe already triggered at start of probing move
     Also, I am unable to deploy the sensor unless I power cycle.

===========================================================

M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled

Config per https://configtool.reprapfirmware.org

config.g

; Configuration file for Duet WiFi (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.2 on Sat Sep 25 2021

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Waterfall" ; set printer name

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S0 ; physical drive 0 goes backwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E103.00 ; set steps per mm
M566 X900.00 Y900.00 Z24.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X300.00 Y300.00 Z100.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S300 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X220 Y220 Z250 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z

; Z-Probe
M950 S0 C"exp.heater7" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-50 Y-15 Z0 ; set Z probe trigger value, offset and trigger height
M557 X15:215 Y15:215 S20 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

deployprobe.g

; deployprobe.g
; called to deploy a physical Z probe
;
; generated by RepRapFirmware Configuration Tool v3.3.2 on Sat Sep 25 2021 05:31:30 GMT-0400 (Eastern Daylight Time)
M280 P0 S10 ; deploy BLTouch