Oh yeah, thats it! Thank you very much, it works
Posts made by SW
-
RE: BL-Touch and the Duex 5
-
RE: Inverting PS_ON levels
Hy, I have an Meanwell PSPA-1000-24 and removed the bridge from the power supply. Then I connected the contacts "Ground" and "PS_on" to the power supply and connect an small 5V power supply (Jumper 5V ext!). If you switch the ATX-Power on (M80) the "PS_on" is connected to the "Ground".
It works fine!
-
BL-Touch and the Duex 5
Hello at all,
if I am connect my BL-Touch direct to the Duett WiFi 1.04 like you see at "Connecting a Z probe" he's working very fine on the Expansion "8) Heater 3". And when I connect the Duex to the Duet and the BL-Touch to PWM1 it seems to work too, I can check the settings with the Macros for the BL-Touch - he's working without changing the settings. But if I start the Homing for the Z-Axis the BL-Touch didn't work, no Pin down and I have to stop homing. Can anyone help me please?
-
RE: Duex 2/5 for 12V
Hello to you
you have to set an Jumper to enable the 12 Volts at Version 0,9 or newer ...
https://duet3d.dozuki.com/Wiki/Duex2_and_Duex5_Features -
RE: U3 "A4403" dead
Hello dc42, it seems that I need your further help. The Supplier send me an eMail on 09.05.2019 " we will analyze your board further and send you a return label in the course of the day." - but I didn't get an return label. I wrote him on the 13.05.2019 a mew Mail, that I didn't get the label, but he dont answer me ... Can you help me please an second time ?
-
RE: Heatbed with 411Watt on Duet Wifi
Ok, I see it's the better way to lave it on the Mosfat
Thank you very much! -
Heatbed with 411Watt on Duet Wifi
Hello Folks,
my Heatbet takes 24 Volt and an resistance (measured) like 17,14 Ohm, this is like 411Watt - 17,14 Amperes. The Fuse on Duet WiFi is like 15 Amperes (Blue). Can I connect direktly to the Duet or did I need an mosfet between the Bed ant the Duet? At this time I connect the Heatbed with an Mosfet, because I don't want to damage my Duet - it works very fine ...
-
RE: ATX Power off at 45° at the Heatend
Oh yes, I thank You very much and check it now ...
-
RE: ATX Power off at 45° at the Heatend
Thank you for this information!
Do you mean i have to write into the End-sequence for my progamms (Slicer Cura) M81 S1 to shut off the ATX-Power?
-
ATX Power off at 45° at the Heatend
Hy at all,
how can I switch ATX power off when the Hotend is under 45°C, because the Fan from the Coldend need ATX-Power and I dont want to damage my Printhead!
If my print is finish I have to wait bevore the system shut down with ATX-Power off. Any Idea? -
U3 "A4403" dead
Hello at all,
I had the same prolems like "U3 burned a hole in itself?" or "Worst day for my Duet Wifi" since February 2019 and my Supplier "Maker...." in Germany didn't answer to my E-Mails since the 8th of February 2019, the last Mail was yesterday (it was the 9th mail)! I buyed an second one Duet WiFi after the damage and this one works fine. The first one is dead. Can you help me please?