Posts made by stefano

you reply is not help, i have different problem with duet wifi original and only one post not possible, i create a post for problem

today other problem with duet 2 wifi 1.0.4c, FAN 0 e FAN 2 not working FAN 1 working and other FAN Ok

@Phaedrux said in Temp hotend not stop other limit and have error:

B3950

Have this error Warning: Auto tune of heater 1 failed due to bad curve fit (A=1636.8, C=129.8, D=6.1)

tomorrow change value and tell if have solve, have list with all code thermistore? have gcode for test thermistore o for see correct number

have image for correct mount? i have test with fan down effector, and if touch nozzle, led gren start, possible not have mount correct? Have see guide smart effector e not have idea error

have thermistore HE3D

4/2/2021, 18:30:14 Warning: Auto tune of heater 1 failed due to bad curve fit (A=1970.5, C=166.0, D=5.6)
4/2/2021, 18:27:40 Auto tune phase 3, peak temperature was 325.5
4/2/2021, 18:27:30 Auto tune phase 2, heater off
4/2/2021, 18:27:00 Auto tune phase 1, heater on
4/2/2021, 18:26:54 M303 H1 S280
Auto tuning heater 1 using target temperature 280.0°C and PWM 0.80 - do not leave printer unattended

@Veti new auto tune ok. If not solve write

yes have see link, not have solution

@Veti remove M500

My print is delta

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.2 on Wed Feb 03 2021 14:20:11 GMT+0100 (Ora standard dell’Europa centrale)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves

; Impostazioni delta
M550 P"OTS Print Turbo Predator" ; set printer name
M665 R175 L430 B165 H431.70 ; imposta raggio delta, lunghezza asta diagonale, raggio stampabile e altezza home
M666 X0 Y0 Z0 ; metti qui le tue regolazioni del finecorsa

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; Motore X
M569 P1 S1 ; Motore Y
M569 P2 S1 ; Motore Z
M569 P3 S0 ; Motore Estrusore E0
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z80.00 E663.00 ; set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Retraction
M207 S4.0 F5000 R-0.025 T2500 Z0.5 ; Firmware retraction

; Axis Limits
M208 Z0 S1 ; set minimum Z

; Fine Corsa
M574 X2 Y2 Z2 S1 ; set active high endstops

; Smart Effector
M558 P0 H25 F600 T4800 ; disable Z probe but set dive height, probe speed and travel speed
M557 R165 S40 ; define mesh grid

; Rilevamento Filamento Interrotto
M591 P1 C3 S1 D0

; Ripristino in Caso di Alimentazione Bassa
M911 S8.0: 19,5: 22,0 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"

; Ripresa di Stampa in Caso di Alimentazione Interrotta
M916

; Heaters
M305 P0 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 0 Hotbend
M143 H0 S100 ; set temperature limit for heater 0 to 100C
M305 P1 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 1 Hotend
M143 H1 S280 ; set temperature limit for heater 1 to 280c
;M570 H1 P4 T15 S0 ; Errore Riscaldatore Hotend
;M570 H0 P4 T15 S0 ; Errore Riscaldatore Hotbend

;Calibrazione Hotend
; M303 H1 P1 T100000 S280 ; impostazione hotend ( H1 ) a piena potentza ( P1 ) termistore ( T ) valore temperatura ( S )
M302 S190 R110 ; Consentire l'estrusione a partire da 120 ° C e le retrazioni già da 110 ° C

; Fans
M106 P0 S0.5 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings

; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
T0 ; select first tool

; Memorizza
M500

; Leggi Parametri
M501

@Phaedrux said in Temp hotend not stop other limit and have error:

M98 P"config.g"

M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: M916: No resume file found

@Phaedrux said in Temp hotend not stop other limit and have error:

https://duet3d.dozuki.com/Wiki/Tuning_the_heater_temperature_control

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later
Board ID: 08DLM-996RU-N8PS4-6J9D0-3SJ6J-KATZR
Used output buffers: 1 of 24 (8 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 92660 of which 340 recycled
Exception stack ram used: 312
Never used ram: 12048
Tasks: NETWORK(ready,676) HEAT(blocked,824) MAIN(running,3752) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:21:19 ago, cause: power up
Last software reset time unknown, reason: User, spinning module GCodes, available RAM 11968 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 2.8ms, max retries 0
MCU temperature: min 16.8, current 22.5, max 22.7
Supply voltage: min 23.6, current 24.1, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2021-02-04 11:26:22
Cache data hit count 3651532045
Slowest loop: 7.96ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 160, MinFreeDm: 160, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 1 is on, I-accum = 0.1
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.77ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8

• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.23
  WiFi MAC address ec:fa:bc:5b:42:c5
  WiFi Vcc 3.45, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 26056
  WiFi IP address 192.168.1.32
  WiFi signal strength -63dBm, reconnections 0, sleep mode modem
  Socket states: 0 0 0 0 0 0 0 0
  === Filament sensors ===
  Extruder 0 sensor: ok

for this i not have start my first print and not have height map with mesh bed compesation

Hi, have duet 2 wifi, version 1.0.4c original, and have this problem.

I if start charge filament, i set temp 190c start temp and not stop 190 and create error high temp 15c, have change cable, problem not solve.

For this not have start test my first print

Hello, all forum

have smart effector duet new version, duet 2 wifi 1.04c, firmware rep rap 2.0.5.1.

Have this problem, smart effector working, fan, led green, etc.. only problem if touch bed not active probe, moving not stop with contact bed.

If i send comand g30 and touch nozzle, moving not stop, if touch up effector, led gren active and stop moving, not have idea for solution, have control cable problem not solve.

have solve problem with jtag

@fcwilt null not see port

@bearer have see all problem not solve

@Phaedrux not possible connect with port usb you solution not solve