Posts made by SoDamnInsane

@droftarts Thank you! FAN0 and FAN2 don't work. I ordered a few MOSFETS. The newer ones, that are installed at the Duet3 mainboard. I hope i have them tomorrow, otherwise it will be de day after tomorrow. I'll post the results here.

@Phaedrux said in Fans not working Duet2 Wifi - Ender 5 Plus:

@SoDamnInsane said in Fans not working Duet2 Wifi - Ender 5 Plus:

When i send M106 P0 S1, the fan for part-cooling doesn't work.

If the fan itself still works correctly when connected to an always on fan pin, than i suspect that the mosfet that controls the fan0 port has failed. Do you notice any damaged chips near the fan0 port?

Is it possible to replace the mosfet on the mainboard? Or is it to expensive to repair the board?

@Phaedrux I can't see any damages on the mainboard.

Yesterday i found a post from 2018. I checked the continuity between the pins, and there is continuity between these pins.

Link to this post

@Phaedrux

Thank you!
When i send M106 P0 S1, the fan for part-cooling doesn't work.
The fan for the hotend is working now!!

These are the results of the commands:

Output M122:

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.5.3 (2024-09-18 11:25:32) running on Duet WiFi 1.02 or later
Board ID: 08DJM-9178L-L2MS8-6JKFJ-3SD6M-TVGAN
Used output buffers: 3 of 26 (18 max)
=== RTOS ===
Static ram: 23376
Dynamic ram: 72952 of which 20 recycled
Never used RAM 17128, free system stack 184 words
Tasks: NETWORK(1,ready,15.0%,217) HEAT(3,nWait 5,0.0%,328) Move(4,nWait 5,0.0%,359) MAIN(1,running,84.7%,742) IDLE(0,ready,0.2%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:07:04 ago, cause: power up
Last software reset at 2024-09-25 19:55, reason: User, Gcodes spinning, available RAM 17128, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
MCU temperature: min 30.3, current 35.9, max 36.4
Supply voltage: min 23.7, current 24.2, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min n/a
Driver 1: standstill, SG min n/a
Driver 2: standstill, SG min n/a
Driver 3: standstill, SG min n/a
Driver 4: standstill, SG min n/a
Driver 5:
Driver 6:
Driver 7:
Driver 8:
Driver 9:
Driver 10:
Driver 11:
Date/time: 2024-09-25 20:06:50
Cache data hit count 4294967295
Slowest loop: 14.85ms; fastest: 0.19ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.5ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, height map offset 0.000, max steps late 0, min interval 0, bad calcs 0, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Movement locks held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Q0 segments left 0
Code queue 0 is empty
=== Network ===
Slowest loop: 20.36ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 1 of 8
=== WiFi ===
Interface state: active
Module is connected to access point
Failed messages: pending 0, notrdy 0, noresp 0
Firmware version 2.1.0
MAC address cc:50:e3:e3:be:42
Module reset reason: Turned on by main processor, Vcc 3.38, flash size 4194304, free heap 39684
WiFi IP address 192.168.86.169
Signal strength -49dBm, channel 6, mode 802.11n, reconnections 0
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0

Output M98 P"config.g":

M98 P"config.g"
HTTP is enabled on port 80
Warning: Heater 0 predicted maximum temperature at full power is 321°C
Warning: Heater 1 predicted maximum temperature at full power is 612°C

@Phaedrux Thank you very much!

; Configuration file for RepRapFirmware on Duet 2 WiFi
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.5.4 on Sat Sep 21 2024 17:05:38 GMT+0200 (Midden-Europese zomertijd)

; General
G90 ; absolute coordinates
M83 ; relative extruder moves
M550 P"Ender 5 Plus" ; set hostname
M911 S19.8 R22 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

; Network
M552 S1 ; configure WiFi adapter
M586 P0 S1 ; configure HTTP

; Smart Drivers
M569 P0 S1 D2 ; driver 0 goes forwards (X axis)
M569 P1 S1 D2 ; driver 1 goes forwards (Y axis)
M569 P2 S0 D2 ; driver 2 goes backwards (Z axis)
M569 P3 S1 D2 ; driver 3 goes forwards (extruder 0)

; Motor Idle Current Reduction
M906 I30 ; set motor current idle factor
M84 S30 ; set motor current idle timeout

; Axes
M584 X0 Y1 Z2 ; set axis mapping
M350 X16 Y16 Z16 I1 ; configure microstepping with interpolation
M906 X800 Y800 Z800 ; set axis driver currents
M92 X80 Y80 Z800 ; configure steps per mm
M208 X0:350 Y6:350 Z0:400 ; set minimum and maximum axis limits
M566 X600 Y600 Z30 ; set maximum instantaneous speed changes (mm/min)
M203 X9000 Y9000 Z499.8 ; set maximum speeds (mm/min)
M201 X1500 Y1500 Z100 ; set accelerations (mm/s^2)

; Extruders
M584 E3 ; set extruder mapping
M350 E16 I1 ; configure microstepping with interpolation
M906 E900 ; set extruder driver currents
M92 E435 ; configure steps per mm
M566 E600 ; set maximum instantaneous speed changes (mm/min)
M203 E6000 ; set maximum speeds (mm/min)
M201 E2000 ; set accelerations (mm/s^2)

; Kinematics
M669 K0 ; configure Cartesian kinematics

; Probes
M558 K0 P9 C"^zprobe.in" H5 F78 T6000 ; configure BLTouch probe via slot #0
G31 P500 X-42 Y-10 Z2.35 ; set Z probe trigger value, offset and trigger height
M950 S0 C"exp.heater3" ; create servo #0 for BLtouch

; Endstops
M574 X2 P"xstop" S1 ; configure X axis endstop
M574 Y2 P"ystop" S1 ; configure Y axis endstop
M574 Z0 ; configure Z axis endstop

; Mesh Bed Compensation
M557 X60:300 Y30:300 S30:30 ; define grid for mesh bed compensation

; Sensors
M308 S0 P"bedtemp" Y"thermistor" A"Heated Bed" T100000 B4012 C7.06e-8 ; configure sensor #0
M308 S1 P"e0temp" Y"thermistor" A"Nozzle" T100000 B4012 C7.06e-8 ; configure sensor #1

; Heaters
M950 H0 C"bedheat" T0 ; create heater #0
M143 H0 P0 T0 C0 S120 A0 ; configure heater monitor #0 for heater #0
M307 H0 R2.43 D5.5 E1.35 K0.56 B1 ; configure model of heater #0
M950 H1 C"e0heat" T1 ; create heater #1
M143 H1 P0 T1 C0 S285 A0 ; configure heater monitor #0 for heater #1
M307 H1 R2.43 D5.5 E1.35 K0.56 B0 ; configure model of heater #1

; Heated beds
M140 P0 H0 ; configure heated bed #0

; Fans
M950 F0 C"fan0" ; create fan #0
M106 P0 C"part-cooling" S0 L0 X1 B0.1 ; configure fan #0
M950 F1 C"fan1" ; create fan #1
M106 P1 C"hotend" S0.65 B0.1 H1 T100 ; configure fan #1
M950 F2 C"fan2" ; create fan #2
M106 P2 S0.85 L0 X1 B0.1 ; configure fan #2

; Tools
M563 P0 D0 H1 F0 ; create tool #0
M568 P0 R0 S0 ; set initial tool #0 active and standby temperatures to 0C

; Miscellaneous
M501 ; load saved parameters from non-volatile memory

; Custom settings
M911 S12 R20 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

I've upgraded my Ender 5 Plus with a Duet2 Wifi mainboard.

Now I'm following the guide for commissioning.
Both Fans are not working when i move the slider!

When i connect the Fan to the ALWAY ON pins, then the fan is working ok.

I used the firmware settings that i found on Github. But these are almost 5 years old...
What can be the problem(s)?

Thanks in Advance!

UPDATE: I tested the extruder Fan with my bench Power Supply. This one is defect!

These are my settings at the moment.

@Phaedrux Sorry, for my late reply! I was very busy the past 2 days. I found a old config file. I'm using the same settings. Now i have another problem with the Fans. But i will post a new question for this.

@droftarts Thank you ver y much!

It is a NEMA 17, that's for sure.
I have the stepper motor installed, so to take a picture is difficult, sorry.
But it looks exactly the same as the one on the picture below.

I'm upgrading a Ender 5 Plus with a Duet2 Wifi, so all the other Stepper motors are from Creality.
I asked a question yesterday, if i could use the same connectors, and just plug them on the Duet2 Wifi.
The answer was that i didn't have to change anything.
So i checked the pancake stepper motor, and it has exactly the same pinout as all the other stepper motors.

Is it correct that this pancake don't use that much current? Because it's used for the extruder (Titan Aero).
I only have to connect the Mosfet and PSU. Then i can power it all up, and hope for the best.

Thank you very much for all the info!!

Last week I bought a, almost new, Ender 5 Plus. Due several circumstances, I couldn't do anything with 3D Printing for 6 years. And I realized that I have forgotten a lot!

Now I want to upgrade the printer with a Duet2 Wifi Mainboard and a direct drive extruder. I have al the parts laying around for about 6 years. So the documents for these parts are lost during these years. There are no Brand or other specs visible on the Pancake stepper motor. And I can hardly remember what I did yesterday, so I can't remember the specs.

What are the best and safest settings in the firmware, to start with?

Thank you in advance!

@jay_s_uk Ohhhh ok! Thank you very much. Due several circumstances i couldn't do anything with 3D Printers for 6 years. But i realized that I've forgotten a lot, to be honest. And now I'm so insecure and doubtful about everything. Thank you!

@SoDamnInsane I'm very sorry, but I'm a little bit confused. Another user posted 4 years ago this picture from his Ender 5 Plus upgrade!.

But when i do a continuous test on the cable, then the connector should be turned 180 degrees. If the schematic of the Nema 17 motor is correct? When i connect it the same way as in the 1st picture, then the first 2 pins from the left are Coil A, instead of coil B...

@jay_s_uk Wauwww. LOL. That was a very quick answer! Thank you very much!!!!!

Hello,

I want to upgrade my Ender 5 Plus form a Creality 4.2.2 mainboard with a Duet2 Wifi mainboard.

Unfortunately i can't find anything about the pinout of the stepper motor connectors on the Creality mainboard.

Can i just unplug them from the Creality mainboard, and connect them straight away on the Duet2 Wifi mainboard?

Thank you in Advance!

@Phaedrux said in Mesh Compensation settings disappear.:

Using always on for the hotend is fine.

If you select tool fan does the slider work to control the tool fan?

Are you sure you have the part cooling fan plugged into the Fan0 port?

I can move the slider(s), but the fan doesn't start.
B.t.w., if I use the FAN1 pins, it works.
Isn't that strange?

@Phaedrux said in Mesh Compensation settings disappear.:

No worries about the questions. We're here to help.

First, the fan question. What exactly doesn't work at this point?

According to your config, you should have Fan0 controllable by slider in the DWC. Fan1 is controlled by the hotend temp.

Your homeall looks fine.

Your slicer start gcode has more than you need. It looks like you've duplicated the entire homeall in there. You only need G28 to call homeall. So remove:

G91 			; relative mode
G1 H2 Z4 F200 		; raise head 4mm
G1 H1 X-240 Y-240 F3000 	; move up to 240mm in the -X and -Y directions until the homing switches are triggered
G1 H2 X4 Y4 F600		; move slowly 6mm in +X and +Y directions
G1 H1 X-10 Y-10 		; move up to 10mm in the -X and -Y directions until the homing switches are triggered
G90 			; back to absolute mode
G1 X80 Y130 F2000 		; put head over the centre of the bed, or wherever you want to probe
G30
G29 S1

And have just G28 instead.

You have T0 commented out in your config.g which means you probably don't have a tool selected at the start of the print, which would explain why it's not heating.

At the end of your config.g you have ;T0 ; select first tool remove the ;
You can also add T0 to your slicer start gcode just to ensure you have a tool selected at the start of the print. That should take care of all cases.

Thanks, @Phaedrux !!

I've connected the extruder fan on the ALWAYS ON pin, as advised by Duet3D. And the part cooling fan on the FAN0 pins. That should be the default firmware settings. I connected the extruder cooling on the ALWAYS ON pins, because I'm afraid that I maybe forget to power this one on. And because I have a Titan Aero direct drive extruder, I have to completely remove the x carrier and disassemble everything, just to replace or unclog the heatbreak/nozzle.

But when I heat up the nozzle. Not one of these sliders are working. ( And the Mesh compensation area can't be changed within the browser.

I have changed the homeall.g file, as you said. I took this example from the manual.
I also changed the tool selection about 1 hour ago, lol.

Thanks again man!!

My homeall.g (what is working well now)

; homeall.g
; called to home all axes
;
; 

G91 						; relative mode
G1 H2 Z4 F200 				; raise head 4mm
G1 H1 X-240 Y-240 F3000 	; move up to 240mm in the -X and -Y directions until the homing switches are triggered
G1 H2 X4 Y4 F600			; move slowly 6mm in +X and +Y 
directions
G1 H1 X-10 Y-10 			; move up to 10mm in the -X and -Y directions until the homing switches are triggered
G90 						; back to absolute mode
G1 X100 Y130 F2000 			; put head over the centre of the bed, or wherever you want to probe
G30 						; lower head, stop when probe triggered and set Z to trigger height
G29 S1

My PrusaSlicer START CODE

G91 			; relative mode
G1 H2 Z4 F200 		; raise head 4mm
G1 H1 X-240 Y-240 F3000 	; move up to 240mm in the -X and -Y directions until the homing switches are triggered
G1 H2 X4 Y4 F600		; move slowly 6mm in +X and +Y directions
G1 H1 X-10 Y-10 		; move up to 10mm in the -X and -Y directions until the homing switches are triggered
G90 			; back to absolute mode
G1 X80 Y130 F2000 		; put head over the centre of the bed, or wherever you want to probe
G30
G29 S1

Sample exported G-Code file

; generated by PrusaSlicer 2.2.0+win64 on 2020-04-12 at 16:41:19 UTC

; 

; external perimeters extrusion width = 0.40mm
; perimeters extrusion width = 0.40mm
; infill extrusion width = 0.40mm
; solid infill extrusion width = 0.40mm
; top infill extrusion width = 0.40mm
; support material extrusion width = 0.35mm
; first layer extrusion width = 0.40mm

M107
M190 S70 ; set bed temperature and wait for it to be reached
M104 S227 ; set temperature
G91 			; relative mode
G1 H2 Z4 F200 		; raise head 4mm
G1 H1 X-240 Y-240 F3000 	; move up to 240mm in the -X and -Y directions until the homing switches are triggered
G1 H2 X4 Y4 F600		; move slowly 6mm in +X and +Y directions
G1 H1 X-10 Y-10 		; move up to 10mm in the -X and -Y directions until the homing switches are triggered
G90 			; back to absolute mode
G1 X80 Y130 F2000 		; put head over the centre of the bed, or wherever you want to probe
G30
G29 S1
M109 S227 ; set temperature and wait for it to be reached
G21 ; set units to millimeters
G90 ; use absolute coordinates
M83 ; use relative distances for extrusion
G1 Z0.200 F7800.000
G1 E-2.00000 F2400.00000
G1 X92.159 Y78.538 F7800.000
G1 E2.00000 F2400.00000

@Phaedrux said in Mesh Compensation settings disappear.:

Please post your homeall.g and your slicer start gcode.

@SoDamnInsane said in Mesh Compensation settings disappear.:

I did that, but it reacts strange.

what does it do?

Sorry for my late reply, I was a little bit sick for a few days. ( No, NOT Corona. lol)

Down here I will post my config.g and PrusaSlicer Start code.

The BL-Touch is working well now.

But there are a few questions left.
I posted them also in a Facebook group, but no reply('s)..

When I or especially you guys can help me with these. Then I'll promise you that I will never post a similar question again. LOL.

Because it's my first Duet2 Wifi mainboard, I'll get confused about all the different answers and tips i get.
Don't misunderstand me, I REALLY appreciate everything you do to help me out, really.
But when 1 problem is solved, I get another one.
These are my 2 final questions... Related to these problems.. Hahaha
1 is PrusaSlider related, so i completely understand that you can't or won't answer them. Np of course

At this moment I have installed:

• Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.0 (2020-01-03b3)
• Duet WiFi Server Version: 1.23
• And Duet Web Control 2.1.1

The questions / problems.

When installed DWC 2.07

• The part cooling fan sliders not working

When installed DWCB 2.1

• The part cooling fan sliders not working
• And the Extrusion Control not working. ( known issue).

When installed DWC 2.1.1

• All the above are working. (Fan sliders and Extrusion Control)
• Mesh compensation NOT working.

As a noob, i think the DWC files don't change my Fan settings.
So, HOW can it be that these only work in DWB 2.1.1?

There are some people saying to change the Fan settings in the config.g file.
But i can't imagine that this is the problem?? Or am i so wrong?

Last and final question

The manual i used to config the probe, said that I have to change my START-Code.
I did that of course.
But when i read the exported G-Code, I see that the temp settings are mentioned twice.
And when i want to print the part right after exporting the G-Code file, the printer starts printing.
And the temperatures are about 30 degrees celsius

I know i ask a lot guys. And I'm really sorry for that.
But i really, really like this mainboard. And my next printer will have a Duet2 or maybe Duet3 mainboard of course,

So i want, and have to learn as most as i can about Duet3D hardware and RRF.
But when several people are saying completely different things, it's hard to get to the point. (for me at least, lol).
And I haven't mentioned that there are differences between de RRF 2.x and RRF 3.x

So i hope you can understand me, and can clear this for me..

Thanks in advance!!!
Greetzzzzz Raymond.

config.g

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by Raymond Ebbers on Tue Apr 7 2020 13:08:56 GMT+0100 (Midden-Europese standaardtijd)

; General preferences BL-Touch Install

G90                                                     ; send absolute coordinates...
M83                                                     ; ...but relative extruder moves
M550 P"Anet AM6"                                        ; set printer name

; Network
M552 S1                                                 ; enable network
M586 P0 S1                                              ; enable HTTP
M586 P1 S0                                              ; disable FTP
M586 P2 S0                                              ; disable Telnet

; Drives
M569 P0 S1                                              ; physical drive 0 goes forwards
M569 P1 S1                                              ; physical drive 1 goes forwards
M569 P2 S0                                              ; physical drive 2 goes backwards
M569 P3 S0                                              ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3                                        ; set drive mapping
M350 X32 Y32 Z32 I0                                     ; configure microstepping without interpolation
M350 E16 I1                                             ; configure microstepping with interpolation
M92 X200.00 Y200.00 Z800.00 E455.59                     ; set steps per mm
M566 X600.00 Y600.00 Z18.00 E300.00                     ; set maximum instantaneous speed changes (mm/min)
M203 X54000.00 Y54000.00 Z720.00 E6000.00               ; set maximum speeds (mm/min)
M201 X9000.00 Y5000.00 Z100.00 E5000.00                 ; set accelerations (mm/s^2)
M906 X720 Y720 Z1460 E1460 I30                          ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                                 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                     	; set axis minima
M208 X237 Y220 Z240 S0                                  ; set axis maxima

; Endstops
M574 X1 S1 P"xstop"                                     ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                                     ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2 P"zstop"                                     ; configure active-high endstop for low end on Z via pin zstop

; Z-Probe
M558 P9 C"^zprobe.in" H5 F500 T2000						; Specify probe type 9 and the input pin
M950 S0 C"exp.heater3"									; Create a GPIO/Servo pin index using your chosen control pin
M557 X0:220 Y20:220 S20                                 ; define mesh grid
G31 X30 Y-15 Z0.87 P25									; Set up the probe offsets, trigger height and trigger value

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950     ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                              ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
M307 H0 B1 S1.00                                   ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                            ; map heated bed to heater 0
M308 S1 P"e0temp" Y"thermistor" T100000 B3950      ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                               ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S290                                       ; set temperature limit for heater 1 to 280C
M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit

; Fans
M950 F0 C"fan0" Q500                                    ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                          ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                                    ; create fan 1 on pin fan1 and set its frequency
M106 P1 S0.7 H1 T45                                       ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                                        ; define tool 0
G10 P0 X0 Y0 Z0                                         ; set tool 0 axis offsets
G10 P0 R0 S0                                            ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"      ; set voltage thresholds and actions to run on power loss
M501                                                    ; load saved parameters from non-volatile memory
;T0                                                      ; select first tool

@PaulHew said in Mesh Compensation settings disappear.:

You may!

Please post your config.g, and firmware version.
What issues are you experiencing?
Do you have a single stepper Z axis or multiple steppers for your Z

Or use the documentation here
https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe
and
https://duet3d.dozuki.com/Wiki/Test_and_calibrate_the_Z_probe

Regards,
Paul.

Hi Paul,

Thx. for replying.

I just downgraded to DWC 2.0.7.
And a few problems are solved now.

But I'm pretty confused, about the settings for the HOME configs ( X, Y, Z and ALL)

And I read that I must also adjust the startcode of the PrusaSlicer.
I did that, but it reacts strange.

I have multiple Z steppers. Upgraded my old Anet A6.

This is my current firmware:

My config.g file

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by Raymond Ebbers on Tue Apr 7 2020 13:08:56 GMT+0100 (Midden-Europese standaardtijd)

; General preferences BL-Touch Install

G90                                                     ; send absolute coordinates...
M83                                                     ; ...but relative extruder moves
M550 P"Anet AM6"                                        ; set printer name

; Network
M552 S1                                                 ; enable network
M586 P0 S1                                              ; enable HTTP
M586 P1 S0                                              ; disable FTP
M586 P2 S0                                              ; disable Telnet

; Drives
M569 P0 S1                                              ; physical drive 0 goes forwards
M569 P1 S1                                              ; physical drive 1 goes forwards
M569 P2 S0                                              ; physical drive 2 goes backwards
M569 P3 S0                                              ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3                                        ; set drive mapping
M350 X32 Y32 Z32 I0                                     ; configure microstepping without interpolation
M350 E16 I1                                             ; configure microstepping with interpolation
M92 X200.00 Y200.00 Z800.00 E430.35                     ; set steps per mm
M566 X600.00 Y600.00 Z18.00 E300.00                     ; set maximum instantaneous speed changes (mm/min)
M203 X54000.00 Y54000.00 Z720.00 E6000.00               ; set maximum speeds (mm/min)
M201 X9000.00 Y5000.00 Z100.00 E5000.00                 ; set accelerations (mm/s^2)
M906 X720 Y720 Z1460 E1460 I30                          ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                                 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                     ; set axis minima
M208 X237 Y220 Z240 S0                                  ; set axis maxima

; Endstops
M574 X1 S1 P"xstop"                                     ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                                     ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2 P"zstop"                                     ; configure active-high endstop for low end on Z via pin zstop

; Z-Probe
M558 P9 C"^zprobe.in" H5 F500 T2000						; Specify probe type 9 and the input pin
M950 S0 C"exp.heater3"									; Create a GPIO/Servo pin index using your chosen control pin
M557 X0:200 Y20:220 S20                                 ; define mesh grid
G31 X39 Y-16 Z2.41 P25									; Set up the probe offsets, trigger height and trigger value

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950     ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                              ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
M307 H0 B1 S1.00                                   ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                            ; map heated bed to heater 0
M308 S1 P"e0temp" Y"thermistor" T100000 B3950      ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                               ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S290                                       ; set temperature limit for heater 1 to 280C
M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit

; Fans
M950 F0 C"fan0" Q500                                    ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                          ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                                    ; create fan 1 on pin fan1 and set its frequency
M106 P1 S0.7 H1 T45                                       ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                                        ; define tool 0
G10 P0 X0 Y0 Z0                                         ; set tool 0 axis offsets
G10 P0 R0 S0                                            ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"      ; set voltage thresholds and actions to run on power loss
M501                                                    ; load saved parameters from non-volatile memory
;T0                                                      ; select first tool

@PaulHew said in Mesh Compensation settings disappear.:

Just upload 2.07 and it will overwrite your current version.
IIRC most of it was bug fixes.
The issue I found was that it did not turn all of my heaters off with 'Turn Everything Off' and there was an issue with the the heightmaps, which may or not be related to your issue.

You could use

M557 X0:200 Y0:220 S20

to define your mesh map.

HTH
Paul.

Thx. Paul. I will try this. Just 1 other question, if I may... What are the best homing configs to use with the BL Touch. I've tried several. But all have other issues.

@PaulHew said in Mesh Compensation settings disappear.:

@SoDamnInsane There has been some issues with the latest version of DWC.
May I suggest you rollback to 2.07, as I had to and wait for the update to 2.1.1

HTH,
Paul.

Thx... I heard this, indeed. But I have the 2.1.1 version already!