In 3.4rc1 the probe now deploys but doesn't retract after probing.
Machine was completely powered off after the update.
M122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.4.0rc1 (2022-02-09 10:27:22) running on Duet 3 Mini5plus WiFi (SBC mode)
Board ID: W4ZW4-V296U-D65J0-40KM0-LR03Z-H6928
Used output buffers: 1 of 40 (14 max)
=== RTOS ===
Static ram: 103652
Dynamic ram: 102128 of which 0 recycled
Never used RAM 35788, free system stack 134 words
Tasks: SBC(ready,3.9%,504) HEAT(notifyWait,0.0%,356) Move(notifyWait,0.0%,292) CanReceiv(notifyWait,0.0%,942) CanSender(notifyWait,0.0%,356) CanClock(delaying,0.0%,339) TMC(notifyWait,1.1%,114) MAIN(running,93.8%,558) IDLE(ready,0.4%,29) AIN(delaying,0.8%,264), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 00:08:35 ago, cause: software
Last software reset at 2022-02-09 18:36, reason: User, GCodes spinning, available RAM 36076, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x00000000 Task SBC Freestk 0 n/a
Error status: 0x00
MCU revision 3, ADC conversions started 515901, completed 515899, timed out 0, errs 0
Step timer max interval 1489
MCU temperature: min 27.5, current 37.5, max 37.8
Supply voltage: min 0.5, current 24.3, max 24.3, under voltage events: 1, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: pos 3760, standstill, SG min 0, read errors 0, write errors 2, ifcnt 13, reads 44146, writes 25, timeouts 0, DMA errors 0, CC errors 0
Driver 1: pos -1280, standstill, SG min 0, read errors 0, write errors 2, ifcnt 10, reads 44148, writes 23, timeouts 0, DMA errors 0, CC errors 0
Driver 2: pos 3560, standstill, SG min 0, read errors 0, write errors 2, ifcnt 10, reads 44147, writes 23, timeouts 0, DMA errors 0, CC errors 0
Driver 3: pos 17104, standstill, SG min 0, read errors 0, write errors 2, ifcnt 15, reads 44140, writes 29, timeouts 0, DMA errors 0, CC errors 0
Driver 4: pos 0, standstill, SG min 0, read errors 0, write errors 2, ifcnt 15, reads 44142, writes 29, timeouts 0, DMA errors 0, CC errors 0
Driver 5: pos 0, standstill, SG min 0, read errors 0, write errors 2, ifcnt 15, reads 44142, writes 29, timeouts 0, DMA errors 0, CC errors 0
Driver 6: pos 0, standstill, SG min 0, read errors 0, write errors 2, ifcnt 15, reads 44140, writes 29, timeouts 0, DMA errors 0, CC errors 0
Date/time: 2022-02-09 18:46:07
Cache data hit count 1160425780
Slowest loop: 60.47ms; fastest: 0.08ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 0.0MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 6, maxWait 48307ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 39, completed 39, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 1], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== Filament sensors ===
Extruder 0 sensor: ok
=== CAN ===
Messages queued 4633, received 0, lost 0, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 18 (min 18), ts 2578/0/0
Tx timeouts 0,0,2577,0,0,2054 last cancelled message type 4514 dest 127
=== SBC interface ===
Transfer state: 4, failed transfers: 0, checksum errors: 0
RX/TX seq numbers: 20857/20857
SPI underruns 0, overruns 0
State: 5, disconnects: 0, timeouts: 0, IAP RAM available 0x0f624
Buffer RX/TX: 0/0-0, open files: 0
=== Duet Control Server ===
Duet Control Server v3.4-rc1
Code buffer space: 4096
Configured SPI speed: 8000000Hz, TfrRdy pin glitches: 0
Full transfers per second: 40.50, max time between full transfers: 47.1ms, max pin wait times: 46.5ms/6.9ms
Codes per second: 0.45
Maximum length of RX/TX data transfers: 3592/1136