Posts made by Printtome3d

Thanks i have put the old DWC and the board work fine, them i have update the DWC to the new 1.21.1 and now works very well this firmware is the better Version of all i have print with the two Duet WiFi and the result is very good. thank for all

ok i try test the DWC on Google Chrome and is Connect to the board but when i click on the settings the DWC disconnect and give me the error SyntaxError: Unexpected token a in JSON at position 216

This is the result of M122 send on USB

< 20:00:39: ResponseBusy
< 20:00:39: Bad recv status size
< 20:00:39: WiFi: avail: 10
< 20:00:39: WiFi: used: 0
< 20:00:39: === Diagnostics ===

< 20:00:39: RepRapFirmware for Duet 2 WiFi/Ethernet version 2.0(RTOS)RC1 running on Duet WiFi 1.02 or later
< 20:00:39: Board ID: 08DDM-9FAM2-LW4S4-6JKF0-3S86J-TLSBX
< 20:00:39: Used output buffers: 1 of 20 (11 max)
< 20:00:39: === RTOS ===
< 20:00:39: Static ram: 28484
< 20:00:39: Dynamic ram: 96036 of whiWiFi: max: 0
< 20:00:39: ch 0 recycled
< 20:00:39: Exception stack ram used: 408
< 20:00:39: Never used ram: 6144
< 20:00:39: Task NETWORK ready, free stack 340
< 20:00:39: Task HEAT blocked, free stack 1260
< 20:00:39: Task MAIN running, free stack 3800
< 20:00:39: === Platform ===
< 20:00:39: Last reset 20:29:50 ago, cause: power up
< 20:00:39: Last software reset at 2018-05-08 00:36, reason: User, spinning module GCodes, WiFi: err: 0
< 20:00:39: available RAM 3848 bytes (slot 2)
< 20:00:39: Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0041f000, BFAR 0xe000ed38, SP 0xffffffff
< 20:00:39: Error status: 0
< 20:00:39: Free file entries: 10
< 20:00:39: SD card 0 detected, inteWiFi:
< 20:00:39: rface speed: 20.0MBytes/sec
< 20:00:39: SD card longest block write time: 0.0ms
< 20:00:39: MCU temperature: min 34.1, WiFi: avail: 4
< 20:00:39: current 34.3, max 38.8
< 20:00:39: Supply voltage: min 0.2, current 0.4, max 12.9, under voltage events: 1, over voltage events: 0
< 20:00:39: Driver 0: standstill, SG min/max not availWiFi: used: 0
< 20:00:39: able
< 20:00:39: Driver 1: standstill, SG min/max not available
< 20:00:39: Driver 2: standstill, SG min/max not available
< 20:00:39: Driver 3: standstill, SG min/maWiFi: max: 0
< 20:00:39: x not available
< 20:00:39: Driver 4: standstill, SG min/max not available
< 20:00:39: Date/time: 2018-05-09 20:00:35
< 20:00:39: Slowest main loop (seconds): 0.0WiFi: err: 0
< 20:00:39: 12307; fastest: 0.000065
< 20:00:39: === Move ===
< 20:00:39: Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm 236, MaxWait: 2696479971ms, Underruns: 0, 0
< 20:00:39: Scheduled moves: 9, completed moves: 9
< 20:00:39: Bed compensation in use: none
< 20:00:39: Bed probe heights: 0.000 0.000 0.000 0.000 0.000
< 20:00:39: === Heat ===
< 20:00:39: Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
< 20:00:39: === GCodes ===
< 20:00:39: Segments left: 0
< 20:00:39: Stack records: 2 allocated, 0 in use
< 20:00:39: Movement lock held by null
< 20:00:39: http is idle in state(s) 0
< 20:00:39: telnet is idle in state(s) 0
< 20:00:39: file is idle in state(s) 0
< 20:00:39: serial is ready with "M122 " in state(s) 0
< 20:00:39: aux is idle in state(s) 0
< 20:00:39: daemon is idle in state(s) 0
< 20:00:39: queue is idle in state(s) 0
< 20:00:39: autopause is idle in state(s) 0
< 20:00:39: Code queue is empty.
< 20:00:39: === Network ===
< 20:00:39: Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
< 20:00:39: HTTP sessions: 0 of 8
< 20:00:39: - WiFi -
< 20:00:39: Network state is running
< 20:00:39: WiFi module is connected to access point
< 20:00:39: Failed messages: pending 0, notready 0, noresp 0
< 20:00:39: WiFi firmware version 1.21
< 20:00:39: WiFi MAC address 60:01:94:34:38:80
< 20:00:39: WiFi Vcc 3.32, reset reason Turned on by main processor
< 20:00:39: WiFi flash size 4194304, free heap 15912
< 20:00:39: WiFi IP address 192.168.1.76
< 20:00:39: WiFi signal strength -62dBm, reconnections 0, sleep mode modem
< 20:00:39: Socket states: 0 0 0 0 0 0 0 0
< 20:00:39: === Expansion ===

this is the error when i try to Connect to the board with the DWC.

SyntaxError: JSON Parse error: Unexpected identifier "nan"

ok i am going to do this and send to you the result of M112

@bmmal said in Firmware 2.0RC1 and 1.21.1RC1 released:

DWC

Hello i have two Duet 3D WiFi and one after Install the new firmware the DWC have crash and reboot when i try to Connect to the board. Can you Help me.

ok i am test and it works very well, thanks

Very good i am going to test thanks.

Hello i use the Cura 3.0.3 with the OctoPrint and now i have by two Duet wifi and i like to do the same on the Duet board, printing direct to the IP but on Cura 3D we need to put API key like Octoprint can you do this on the Duet Wifi?