Posts made by Polyneutron21

@jay_s_uk I took it out of the printer, connected it to a 24 VDC power supply and the pi to the computer with the USBC and the 24-40 pin cables. The wiring could not be simpler yet there was no change. I updated the firmware in the Pi 5 to 3.5.4 but the transfer pin faulted there as well. The update did finish.

Then I took it all down to pieces and used only the microSD card that came with the board and a USBC cable to the computer and the computer doesn't see it and the device manager doesn't have it.

@Phaedrux I would rather use SBC mode. if I cannot get the SBC mode straight, there is little to no point. I have Two Manta M8P with integrated CM4 with 8 gb memory and 16GB EMMC and I had klipper on the emmc for years. CanFD was the clear choice as Can was too flakey. I still have a couple EBB36 tool boards but UUID's kept getting lost.

@elmoret Let me know what shipping is and preferred way of payment.

@droftarts I just shh into Pi and updated to version 3.5.4 and still waiting for transfer PIN. I will take out the Pi5 again and then put the card in and follow the instructions on getting it to stand alone. What is the point of all this. I think it is time to move past duet.

@Polyneutron21 I looked at the contents of the Micro SD that came with the 6HC and put it back into the 6HC then connected to the ethernet and only the red and green lights are on but I don't see any communication through the router. Do I need a jumper or something to tell it to go to stand alone mode?

@droftarts I did remove the 16GB micro SD but this did not resolve the "Timeout waiting for transfer pin" and I have two Pi 5's and have tried both. The one dedicated to the SBC roll used to work fine. I took the Pi5 off the display and tried that one with a fresh image but that didn't work either. I also have two 24-40 pin cables and neither of those make a difference.

@andywm I have the same issue. I had Chinese boards that played nice until they started getting drop outs. I purchased a genuine Duet 3 6HC and used the included cable to connect the Pi5 to the 6HC and "Timeout waiting for transfer pin. I noticed a 16 gb micro-SD card in the 6HC and thought it may be the issue, but no. Then I tried a new 24-40 pin cable and still had the same issue. Formatted thee 64GB stick with 2024-09-19-DuetPi_arm64.img and tried it after booting all Led's were bright but still had the same issue, tried a different Pi5 with a fresh copy and still "timeout waiting for transfer pin.

I am at the end of my rope,

@T3P3Tony
Thank you for verifying that. Something must have happened to the GPIO of the 6HC or Pi 5.

@lukeatkin
I created on open in the Duet GPIO 26 pin to 40 pin cable. I purchased another one from Geekpi and it will not allow the PI 5 to boot. I believe the Duet cable is wired differently than the downgrade 26 Pin to 40 pin cable. I have wired as pictured and the red light just blinks. There is only one other way to install the 40 pin and that wouldn't work either. Where might I find the original Duet 3 6HC to Pi GIPO cable.

This adapter looks at can A,B,C and FD and communicates between them. I haven't worked on this again up to this point. I was looking forward to the Duet Scanning Z probe but this is the fourth one I have purchased. The first one worked until the cable plug fell off. The second the input shaping loosed a screw and damaged the probe board. The third and fourth where DOA. So, I plan to pick this up again. If I can detect the voltage change as the cartographer sees the bed and lights blue. Then pulling away the light goes off. If I can, I will write the codes into the config. I will also see if this Can FD capable board will communicate through can.

I have had miserable luck with the duet 3 scanning probe. I just purchased a can adapter board from Amazon that is engineered so much better. Surface mount components but through hole tech for USB-C and Can cables. I ran the 5VDC line from the Cartographer 3d v3 to the same 5VDC as the USB and connect the ground can L and Can H to the screw terminals on the adapter board. Then I connected the green (CanH) and white (CanL) to the 1LC and the 5VDC and ground to the 5VDC plug used for the SZP. The blue light on the cartographer is blue when proximity to the bed is close and off when moved away from the bed. I have to enter the codes in the Config, but it appears to be working.

I have been using the Duet 3 scanning z probe and the third one has an internal short. I pugged in the board to the SZP per documentation and no LED lights and didn't show up in the web control. What I did notice was the temp on the hot end probe was now 2000C. I shut the Voron down and unplugged the Z probe board. I then booted it back up and the hot end was 22.8 and active. I checked the red 3.27vdc and black ground. The plug to the probe is black, red 3.3VDC, black Can low and red can High. I am using the supplied wires from the Duet 3 1LC, The other probes were working well this one hasn't worked at all. I have contacted Fila Studer and they asked me to enter it into the forum. Attached is a picture of the setup that was working.
[link text]

The different B values where the key. I tried the probe on temp1 and it worked. The hot end tool board was 23,6°C which is now controllable. I checked the pin connectors and plugged it into Temp0 and after booting it up it works their as well. B values affect the reported temperature.

I have tried different configurations of 308 in relation to B and C values and nothing changes, the Tool temperature is reporting 2000C, My current 308 command is: M308 S1 P"121.temp0" Y"thermistor" T10000 B4725 C7.06e-8 ;

Everything else on the tool board is working but the nozzle will not heat until the temperature probe reads correctly.
I have changed the B and C values and nothing changes it is always 20000C.

The original probe was faulty and reported 2000C and -273 or disconnected. This is a brand new probe from Revo.

This is all mounted on a Voron 2.4 R2 with the Duet 3 6HC with Duet 3 1LC and Duet 3 SZP. I am at the end of my rope and thinking about scrapping all of it for a different printer.

The SZP show up in the Duet Web control, and communication looks great, the problem is with M308 is says S10 is not a valid sensor pin.

I have the X on drive 0 , Y on drive 1, Z FR on drive 2, Z RR on drive 3 and Z RL on drive 4 and z FL on drive 5. When I home the X and Y work but the Z front left and the Z rear left go up while Z rear left and Z on front right go done binding the gantry. All Kysan Ocean motors are left to right (Red, Green, Yellow, Blue) and the are all paired the same. Do I need to re-wire rear right and front left motors or am I missing something. The printer is a Voron 2.4 R2.

The config.g:

; Configuration file for RepRapFirmware on Duet 3 Main Board 6HC
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.5.8 on Mon Nov 25 2024 09:23:39 GMT-0600 (Central Standard Time)

; General
G90 ; absolute coordinates
M83 ; relative extruder moves
M550 P"Duet 3" ; set hostname

; Network
M551 P"Voron24" ; set UI password

; Accelerometers


; Smart Drivers
M569 P0.0 S1 D2 ; driver 0.0 goes forwards (X axis)
M569 P0.1 S1 D2 ; driver 0.1 goes forwards (Y axis)
M569 P0.2 S1 D2 ; driver 0.2 goes forwards (Z axis)
M569 P0.3 S1 D2 ; driver 0.3 goes forwards (Z axis)
M569 P0.4 S1 D2 ; driver 0.4 goes forwards (Z axis)
M569 P0.5 S1 D2 ; driver 0.5 goes forwards (Z axis)

; Motor Idle Current Reduction
M906 I30 ; set motor current idle factor
M84 S30 ; set motor current idle timeout

; Axes
M584 X0.0 Y0.1 Z0.2:0.3:0.4:0.5 ; set axis mapping
M350 X16 Y16 Z16 I1 ; configure microstepping with interpolation
M906 X800 Y800 Z800 ; set axis driver currents
M92 X80 Y80 Z80 ; configure steps per mm
M208 X0:350 Y0:350 Z0:300 ; set minimum and maximum axis limits
M566 X900 Y900 Z900 ; set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z6000 ; set maximum speeds (mm/min)
M201 X500 Y500 Z500 ; set accelerations (mm/s^2)

; Kinematics
M669 K1 ; configure CoreXY kinematics

; Endstops
M574 X1 P"io0.in" S1 ; configure X axis endstop
M574 Y1 P"io1.in" S1 ; configure Y axis endstop


; Sensors
M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermister on pins to temp0

; Heaters
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 S1.00 ;disable bang bang mode for the bed heater and set PWM limit
M143 H1 S320 ; Set temperature range for heater 0-320C

; Heated beds
M140 H0 ; map heated bed to heater 0


; Fans
M950 Fo C'121.out1" Q500 ;Ceate fan0 on pin 121.out1 and set frequency
M106 P0 S0 H-1 ;set fan 0 value
M950 F0 C"out7" ; create fan #0
M106 P0 S0.5 L0 X1 B0.1 ; configure fan #0
M950 F1 C"out8" ; create fan #1
M106 P1 S0.5 B0.1 H1 T0 ; configure fan #1

; Tools
M563 P0 D0 H1 F0 ; create tool #0
M568 P0 R0 S0 ; set initial tool #0 active and standby temperatures to 0C

; Miscellaneous
M501 ; load saved parameters from non-volatile memory

Re: [Duet 3 6HC + Scanning Z Probe](not connecting)
Using the Duet 3 1LC tool board and scanning Z probe, I think the board is DOA. I get no LED light. I verified I am getting 4.99VDC at the SZP board, I also verified the CanH and CanL which are black and red wires. The tool board is working to control nozzle temp, extruder motor, hear break fan, filament fan and a BTT smart filament sensor. The SZP led is bad or the board is bad.