Topics created by pipersw

In bed.g you should probably use M561 at the start of the file.

So, I will wait for the Duet 3 Mini, for the TMC2209 with steathlchop

@pipersw said in Duet2Wifi not conenct to wifi after reset:

ESP12S

you can use pretty much any ESP module with the same footprint, i.e. ESP12F and ESP12E, or ESP07 all work, but there differences in the certifications like ce/ul/fcc that matter for businesses.

You can use any SD card slot with the same footprint, but the Würth was chosen for superior quality, I opted for cheap chinesium* https://www.aliexpress.com/item/32972228521.html

(ed: * because ordering 1 of the Würth + shipping is crazy, however I will add a proper one next time I have to order from digikey anyway)

@droftarts

I plan to do the same with my IDEX!

I would also like to reference both tools with one piezo sensor each.

Where do you write these commands? Does all of this come to homez.g?

I take a different approach and do things the other way round. That is to say, I keep and maintain "master" copies of everything on a PC and back up to a NAS/cloud storage, then only ever upload to the Duet board.

@bearer thanks

Interpolation is enabled, I will reduce to 800mA my 1.68A motors.
I put some dampers under the printer. Damper on steppers don't reduce the noise.

If you're trying to measure wall thickness for extruder calibration, try this method instead: https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+4:+Calibration/40#s165

Then if you want to measure dimensional accuracy, print a larger complete cube and measure total width on the sides and on the diagonals.

@SIam said in Run-out sensor on duet2 expansion connector:

m591 D0 P2 C"zstop" S1

thanks !!

All the fans connectors are used already.
So I have to

put pump + flowmeter + fan on fan 1 connector ? or just the fan on fan 1 connector, and the pump + flowmeter on 12V (thought DCDC 24V controled by PS_ON) ?

If you mount the duet outside vertically with enough air vents it likely won't need a fan at all unless you're running 2a+ current.

@pipersw said in RRF3 and pb6:

I want monitoring a flow meter, not FAN0.
If I use C"fan0+^exp.pb6", there is a li,k between fan0 and pb6 ?

The link is that Duet Web Control may associate the RPM reading with fan0.

Found : koolance FIT-V03

text alternatif

@lael they’ve been great, and I only need two sets. They are also often used in food service to connect/disconnect fluids like soda syrup, beer taps, etc.

Like you said, it allows me to quick disconnect the hotend for whatever reason without any major disassembly, or if I want to locally drain it without emptying the entire loop.

You are right. I will calibrate the z height.
Thx

It's the peak current I have found a post
https://forum.duet3d.com/topic/5392/does-m906-set-rms-or-peak-current

@pipersw said in Need some advice on my config files for bed levelling:

I have to do a G28 Z or a G30 Z0 at the end of bed.g ?

I would think so, since any tilt correction would have moved the Z0 position at the center of the bed.

@jayjay, international shipping rate is a funny business, I can buy from china products that cost less, including shipping to the US, than it would costs me to ship domestic.

Try for example to ship to China a returned product, it will cost you significantly more than you paid for the product + shipping.

@pipersw This should work. Though for type drivers the P parameter is ignored and can be left out.