Hello
I would like to know if you have solved the problem of the zprob, with the pressure sensor.
I only get the first touch, then error!
does not reopen the contact

Hello and thanks
But I didn't understand which line I have to write in config.g, M307 vp13,4 10950 d51,5?
Exact

@Phaedrux
i uploaded frw 2.05.
now the bed, and the rest, works, done autotuning of all the heaters, and the next step is to do the first test pieces, to see the last calibrations.

Hello
I have a problem with the heatbed. after several autopid (m303) and data readings, save and reset.
insists on not functioning normally.
I went from megatronic where it worked, with duet I have a time / c ° error.
the plate is 8mm aluminum + 5mm glass.
My config.g is:

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.2 on Wed Jan 20 2021 20:48:08 GMT+0100 (Ora standard dell’Europa centrale)

; General preferences

G90 ; send absolute coordinates...

M83 ; ...but relative extruder moves

M550 P"Bad Printer 2 (3.2)" ; set printer name

M669 K1 ; select CoreXY mode

; Network

M552 S1 ; enable network

M586 P0 S1 ; enable HTTP

M586 P1 S0 ; disable FTP

M586 P2 S0 ; disable Telnet

; Drives

M569 P0 S1 ; physical drive 0 goes forwards

M569 P1 S1 ; physical drive 1 goes forwards

M569 P2 S0 ; physical drive 2 goes backwards

M569 P3 S1 ; physical drive 3 goes forwards

M569 P4 S0 ; physical drive 4 goes backwards

M584 X0 Y1 Z2 E3:4 ; set drive mapping

M350 X16 Y16 Z16 E16:16 I1 ; configure microstepping with interpolation
M92 X81.00 Y81.00 Z1600.00 E94.00:94.00 ; set steps per mm

M566 X900.00 Y900.00 Z300.00 E300.00:300.00 ; set maximum instantaneous speed changes (mm/min)

M203 X12000.00 Y12000.00 Z600.00 E6000.00:6000.00 ; set maximum speeds (mm/min)

M201 X1500.00 Y1500.00 Z100.00 E10000.00:10000.00 ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E1000:1000 I30 ; set motor currents (mA) and motor idle factor in per cent

M84 S180 ; Set idle timeout

; Axis Limits

M208 X-26 Y-12 Z0 S1 ; set axis minima

M208 X235 Y225 Z215 S0 ; set axis maxima

; Endstops

M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop

M574 Z1 S1 P"zstop" ; configure active-high endstop for low end on Z via pin zstop

; Z-Probe

M558 P0 H10 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed

M557 X10:200 Y10:200 S40 ; define mesh grid

; Heaters

M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 R4700 ; configure sensor 0 as thermistor on pin bedtemp

M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0

M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit

M140 H0 ; map heated bed to heater 0

M143 H0 S100 ; set temperature limit for heater 0 to 100C

M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp

M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1

M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S285 ; set temperature limit for heater 1 to 285
C
M308 S2 P"e1temp" Y"thermistor" T100000 B4138 ; configure sensor 2 as thermistor on pin e1temp

M950 H2 C"e1heat" T2 ; create nozzle heater output on e1heat and map it to sensor 2
M
307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H2 S285 ; set temperature limit for heater 2 to 285C

; Fans

M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency

M106 P0 C"testa" S0 H-1 ; set fan 0 name and value. Thermostatic control is turned off

M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency

M106 P1 C" cpu" S0 H0 T40 ; set fan 1 name and value. Thermostatic control is turned on

; Tools

M563 P0 S"hot end 0" D0 H1 F0 ; define tool 0

G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets

G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

M563 P1 S"hot end 1" D1 H2 F0 ; define tool 1

G10 P1 X0 Y26 Z0 ; set tool 1 axis offsets

G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C
M501

; Custom settings

override.g
M122 ; stop emergenza esterno

M591 ; rilevamento filo inceppato

M500 ; salva eprom

M581 ; configurazione del trigger esterno

M555 ; imposta compatibilità

M501 ; legge i parametri memorizzati

M70 ; caricamento del filamento

M70 ; scaricare il filamento

M90 ; Imposta data e ora locali

; Miscellaneous

M575 P1 S1 B57600 ; enable support for PanelDue

M501 ; load saved parameters from non-volatile memory

M911 S10 R11 P" M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

would it be better to go back to FW 2.05? from the mecatronic switch to duet I have not yet printed anything, I'm curious to see how it works

@Phaedrux I tried again to bring the m303 to 60 ° with the command.
with m307 I have the data but as I said, I have always noticed the same, saved and reset.
Same error in normal set (0.4 ° / sec).

or

@Veti yes I have read various forums, and it is a line that I have added in config.g.
In my stupidity, I doubt that I don't take M500, as every m307 I do, the basic and varied results are identical.

Hello
I am new, I also bought a duet wifi, and loaded FRW 3.2.
also I have the same problem, I have done the pid several times, asked m307 h0 to follow m500, reset at the next restart I get the same error again.
WRONG I something?
Machine stopped on the table, and I can't get it printed