@Veti said in error upgrading:
M558 P8 C"^!zprobe.in" H5 F450 T5000 R1
Yes Awesome !!!! it works,
Cant thank you all enough for being helpful. Now i can sleep.
@Veti said in error upgrading:
M558 P8 C"^!zprobe.in" H5 F450 T5000 R1
Yes Awesome !!!! it works,
Cant thank you all enough for being helpful. Now i can sleep.
@grizewald
Hey thanks for that. Iām not at the printer till tomorrow now but I will defiantly try a few of those settings.
Keep my fingers crossed as I've spent hours trying to solve it.
I'll let you know how it goes.
@deckingman Much appreciated. Looks like i will stick to the 16.
OK, long story short, I tried to go to the 2.05 first but had the same error. Then I copied the missing file "Duet2CombinedIAP.bin" from the v 3.00 and put it into the /sys file on the SD card. Hey hit the money, all the upgrades went as they should.
@grizewald said in Precision piezo auto bed compensation issues. Please help.:
G32
Holy Cow!! How backward can I be. My wires are connected to the endstop. Thanks for the picture, with out it I would have been convinced we where talking about the same thing.
I've just redone it now and started the mess. Looks like its working.
Many Many thanks. You've been a huge help.
You're a Legend, works like a charm. Thank you so much, it seems simple enough when you see it but I was trying all the wrong way. Much appreciated.
Hi all, I have a small issue that I'm hoping is a quick fix. My fan0 on my duet WIFI 2 is not working(no problem its toast) and i have connected my parts cooling fan to fan1. My g code is messed up as it only works as a hot end tool fan. Comes on as soon as the hot end heats up. The actual hot end fan is connected to a 24 v source an is always on already. The fan control on the screen has no effect on the fan speed. my g-code must be messed up, not sure if i have too free up the default F0 first?? the related g-code I have is below. All i would like is to have the parts cooling fan controlled by the screen fan and working on fan1 pin.
Please help this ignorant brain. Thanks.
M950 F0 C"fan0" Q500 ;new settings ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ;new settings ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M563 P0 S"Mosquito" D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0
@Veti said in Fan Control Issue:
find the correct beta value in your thermistor
Evidently my hot end temp sensor
is as follows:
2M NTC 3950 100K Ohm High Temperature Resistance
Could i ask how and what setting to put in to the config.g for this?
Ill go see where it came from. Sorry not a jumper, I meant the connector from the fans that go onto the board.
@Veti said in Fan Controll Issue:
B4138
Thanks for your help.
Regarding the B4138, i don't have any documentation regarding that. Ive looked through old setups and that's the one that its always used. How could i test this is correct?
Jip, everything now seems to work, I'll replace the connector, it looks OK but somethings off.
Ok.. so after plugging the jumper into always on then back to pin 1 they are now working????