Posts made by nicaris

Hi all
Could use some help homing my Ender 5 plus running a Duet 2 wifi .
I completely mashed my config (working on a different printer ) but this had been working fine.
Now I can home X and Y but when I try to home Z the print head moves away form the X endstop .

Links to my Config.g and Homeall :
config.g homeall.g

@mesacrash
Either a soldering iron or cigarette lighter will do the trick

@phaedrux Thanks for that... it's happened a couple of times without me realising !

Would it be possible to create an event / shutdown when the heatsink fan is not running?
My fingers are dyslexic and eyes short . Fan is practically silent (wish I could say the same about my wife ).
This would save a lot of jiggery - pokery.

@nicaris Thanks for the swift response -do I just remove the H1 from that line ?

Hi ...I'm back !
I've got things sorted and had some prints at last . Now i need to put everything back in it's box and am having a problem with the fan that will cool the motherboard. this is my Config.g but fan 2 does not show up in the console/dashboard ?
; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; original version generated by RepRapFirmware Configuration Tool v2.1.8 on Fri Apr 10 2020 21:58:05 GMT-0600 (Mountain Daylight Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Nick's Ender +5+ " ; set printer name
M552 S1
; Network
M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S0 ; physical drive 0 goes forewards
M569 P1 S0 ; physical drive 1 goes forewards
M569 P2 S1 ; physical drive 2 goes forewards
M569 P3 S1
M569 P4 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2:4 E3 ; set drive mapping
; Settings w/o interpolation - commented out
;M350 X32 Y32 Z32 E128 I1 ; configure microstepping with interpolation
;M92 X160.00 Y160.00 Z1600.00 E3533 ; set steps per mm
;M566 X600.00 Y600.00 Z60.00 E1200.00 ; set maximum instantaneous speed changes (mm/min)120
;M203 X9000.00 Y9000.00 Z1200.00 E6000.00 ; set maximum speeds (mm/min)
;M201 X3000.00 Y3000.00 Z60.00 E2500.00 ; set accelerations (mm/s^2)250
; Settings w/ interpolation @ 16
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z800.00 E130.15 ; set steps per mm130.15
M566 X600.00 Y600.00 Z30.00 E300.00 ; set maximum instantaneous speed changes (mm/min)300
M203 X9000.00 Y9000.00 Z500.00 E5000.00 ; set maximum speeds (mm/min)
M201 X800.00 Y800.00 Z250.00 E1000.00 ; set accelerations (mm/s^2)1500
M906 X400 Y300 Z350 E900 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y6 Z0 S1 ; set axis minima
M208 X350 Y350 Z400 S0 ; set axis maxima

; Endstops
M574 Z0 ; disabled end stop for z c
M574 X1 S1 P"xstop" ; active low endstop for x-axis
M574 Y1 S1 P"ystop" ; active low endstop for y-axis

; Filament Sensor
M591 D0 P1 S1 C"e0stop"

; Z-Probe
; Based on https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe#Section_Duet_2_WiFi_Ethernet_without_expansion_board
M307 H3 A-1 C-1 D-1
M280 P5 S10 I1 :c
M950 S0 C"exp.heater3" ; Set exp.heater3 (pin8 on expansion socket) as servo pin 0 for BLTouch c
M558 P9 C"^zprobe.in" H5 F120 T6000 A5 R0.1 X0 Y) Z1 ; set Z probe type to bltouch and the dive height + speeds c
G31 P500 X-28 Y-13 Z3.54 ; set Z probe trigger value, offset and trigger height c pla3.65
M557 X0:300 Y0:300 S20 ; define mesh grid
M574 Z1 S2;c
M280 P5 S90 I1
; Sensors
; See https://duet3d.dozuki.com/Wiki/RepRapFirmware_3_overview#Section_Pin_names_for_Duet_2_WiFi_Ethernet
; for pin names
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; Bed Thermistor
; I replaced my original e0temp thermistor, so if you have stock, use the same values as bed
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; Extruder Thermistor

; Heaters
M950 H0 C"bedheat" T0 ; Create a heater using the bedheat output and the S0 temp sensor (bed heater)
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M143 H0 S120 ; set temperature limit for heater 0 to 120CC0.0000000706
M140 H0 ; Set heater H0 as the bed heater
M950 H1 C"e0heat" T1 ; Create a heater using the e0heat output and the S1 temp sensor (extruder 0)
M143 H1 S290 ; set temperature limit for heater 1 to 290C

; Bed adjustment screw locations
M671 X15:300:300:15 Y35:40:320:320 P0.7 ; mark leveling screws at (316,295) (316,35) (46,295) (46,35)

; Fans
M950 F0 C"fan0" Q500 ; Set fan 0 to pin "fan0" with PWM freq 500 Hz
M106 P0 C"part-cooling" S0.10 H-1 ; set fan 0 name and fan speed to 65%. Thermostatic control is turned oncp0 h0
M950 F1 C"Fan1" Q500 ; Set fan 1 to pin "fan1" with PWM freq 500 Hz
M106 P1 C"hotend" S0.50 H1 T100 ; set fan 1 name and fan speed. Thermostatic control is turned off
M950 F2 C"fan2" Q500 ; Set fan 2 to pin "fan2" with PWM freq 500 Hz
M106 P2 C"fan2" S0.50 H1 T100 ; set fan 2 speed. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501 ; load saved parameters from non-volatile memory
M911 S12 R20 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
Thanks in anticipation of your help

@nicaris
So at the moment the height map is saved in heightmap.csv
I create a file called mesh.g for that ? and remove the m401 and m402 from bed.g

@fcwilt Thanks again for your help- it will take some time to make the adjustments needed .
These are my Config Files :
; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; original version generated by RepRapFirmware Configuration Tool v2.1.8 on Fri Apr 10 2020 21:58:05 GMT-0600 (Mountain Daylight Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Nick's Ender +5+ " ; set printer name
M552 S1
; Network
M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S0 ; physical drive 0 goes forewards
M569 P1 S0 ; physical drive 1 goes forewards
M569 P2 S1 ; physical drive 2 goes forewards
M569 P3 S1
M569 P4 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2:4 E3 ; set drive mapping
; Settings w/o interpolation - commented out
;M350 X32 Y32 Z32 E128 I1 ; configure microstepping with interpolation
;M92 X160.00 Y160.00 Z1600.00 E3533 ; set steps per mm
;M566 X600.00 Y600.00 Z60.00 E1200.00 ; set maximum instantaneous speed changes (mm/min)120
;M203 X9000.00 Y9000.00 Z1200.00 E6000.00 ; set maximum speeds (mm/min)
;M201 X3000.00 Y3000.00 Z60.00 E2500.00 ; set accelerations (mm/s^2)250
; Settings w/ interpolation @ 16
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z800.00 E140 ; set steps per mm
M566 X600.00 Y600.00 Z30.00 E1200.00 ; set maximum instantaneous speed changes (mm/min)300
M203 X9000.00 Y9000.00 Z500.00 E6000.00 ; set maximum speeds (mm/min)
M201 X800.00 Y800.00 Z250.00 E2500.00 ; set accelerations (mm/s^2)1500
M906 X600 Y600 Z600 E900 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y6 Z0 S1 ; set axis minima
M208 X350 Y350 Z400 S0 ; set axis maxima

; Endstops
M574 Z0 ; disabled end stop for z c
M574 X1 S1 P"xstop" ; active low endstop for x-axis
M574 Y1 S1 P"ystop" ; active low endstop for y-axis

; Filament Sensor
M591 D0 P1 S1 C"e0stop"

; Z-Probe
; Based on https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe#Section_Duet_2_WiFi_Ethernet_without_expansion_board
M307 H3 A-1 C-1 D-1
M280 P5 S10 I1 :c
M950 S0 C"exp.heater3" ; Set exp.heater3 (pin8 on expansion socket) as servo pin 0 for BLTouch c
M558 P9 C"^zprobe.in" H5 F120 T6000 A5 R0.1 X0 Y) Z1 ; set Z probe type to bltouch and the dive height + speeds c
G31 P500 X-28 Y-13 Z3.48 ; set Z probe trigger value, offset and trigger height c
M557 X0:300 Y0:300 S20 ; define mesh grid
M574 Z1 S2;c
M280 P5 S90 I1
; Sensors
; See https://duet3d.dozuki.com/Wiki/RepRapFirmware_3_overview#Section_Pin_names_for_Duet_2_WiFi_Ethernet
; for pin names
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; Bed Thermistor
; I replaced my original e0temp thermistor, so if you have stock, use the same values as bed
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; Extruder Thermistor

; Heaters
M950 H0 C"bedheat" T0 ; Create a heater using the bedheat output and the S0 temp sensor (bed heater)
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M143 H0 S120 ; set temperature limit for heater 0 to 120CC0.0000000706
M140 H0 ; Set heater H0 as the bed heater
M950 H1 C"e0heat" T1 ; Create a heater using the e0heat output and the S1 temp sensor (extruder 0)
M143 H1 S290 ; set temperature limit for heater 1 to 290C

; Bed adjustment screw locations
M671 X15:300:300:15 Y35:40:320:320 P0.7 ; mark leveling screws at (316,295) (316,35) (46,295) (46,35)

; Fans
M950 F0 C"fan0" Q500 ; Set fan 0 to pin "fan0" with PWM freq 500 Hz
M106 P0 C"part-cooling" S0.65 H-1 ; set fan 0 name and fan speed to 65%. Thermostatic control is turned oncp0 h0
M950 F1 C"Fan1" Q500 ; Set fan 1 to pin "fan1" with PWM freq 500 Hz
M106 P1 C"hotend" S0.50 H1 T100 ; set fan 1 name and fan speed. Thermostatic control is turned off
M950 F2 C"fan2" Q500 ; Set fan 2 to pin "fan2" with PWM freq 500 Hz
M106 P2 S0.85 H-1 ; set fan 2 speed. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501 ; load saved parameters from non-volatile memory
M911 S12 R20 P"M913 X0 Y0 G91 M83 G1

; bed.g
; called to perform automatic bed compensation via G32
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Thu Feb 17 2022 16:47:45 GMT+0000 (Greenwich Mean Time)
M561 ; clear any bed transform
G29 ; probe the bed and enable compensation
G28 ; home
M401 ; deploy Z probe
G30 P0 X35 Y35 Z-99999 ; probe near an adjusting screw
G30 P1 X300 Y40 Z-99999 ; probe near an adjusting screw
G30 P2 X300 Y320 Z-99999 ; probe near an adjusting screw
G30 P3 X35 Y320 Z-99999 S4 ; 4th adj screw and report adjustments needed
M402 ; retract probe

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Thu Feb 17 2022 16:47:45 GMT+0000 (Greenwich Mean Time)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-355 Y-355 F1800 ; move quickly to X or Y endstop and stop there (first pass)
G1 H1 X-355 ; home X axis
G1 H1 Y-355 ; home Y axis
G1 X5 Y5 F6000 ; go back a few mm
G1 H1 X-355 F360 ; move slowly to X axis endstop once more (second pass)
G1 H1 Y-355 ; then move slowly to Y axis endstop
G90 ; absolute positioning
G1 X15 Y15 F6000 ; go to first bed probe point and home Z
G30 ; home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

Thanks again in advance -I think I'm going to need some help with retraction settings

@fcwilt Yes 4 ( 1in each corner)... how do i use them in reprap ?

@fcwilt Thanks again that has removed the error after bed and mesh levelling but i still have that tilt.

@fcwilt Thanks for the swift reply and yes it was concerning mesh levelling (but I get the same error in bed levelling).
I am new to this and have struggled ..why would the height map appear tilted when the bed definitely isn't ?

Help !
I'm still having problems-this time concerning bed levelling
Unfortunately I have no idea what this means;
Warning: the height map has a substantial Z offset

I have repeatedly calibrated the Z height but nothing seems to make any difference .Needless to say I haven't managed to print anything yet.

Thoughts anyone?

@phaedrux
Thanks for that

@nicaris said in Duet 2 Wifi Problems with BL Touch:

@nicaris said in Duet 2 Wifi Problems with BL Touch:

@nicaris
Hi Thanks for responding THese are my config files.
M401 and 402 do not work (m280 does)

m122

=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9K662-MGPSN-6J1FD-3SJ6M-TBYAW
Used output buffers: 3 of 24 (11 max)
=== RTOS ===
Static ram: 23876
Dynamic ram: 75448 of which 12 recycled
Never used RAM 15080, free system stack 184 words
Tasks: NETWORK(ready,12.2%,237) HEAT(delaying,0.0%,314) Move(notifyWait,0.1%,364) MAIN(running,86.4%,441) IDLE(ready,1.4%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:01:10 ago, cause: power up
Last software reset at 2022-02-20 20:14, reason: User, GCodes spinning, available RAM 12048, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 0
MCU temperature: min 22.1, current 27.3, max 27.4
Supply voltage: min 24.0, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2022-02-21 09:36:00
Cache data hit count 2538616899
Slowest loop: 5.80ms; fastest: 0.17ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 4.9ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0 sensor: ok
=== Network ===
Slowest loop: 40.21ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

• WiFi -
  Network state is active
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.23
  WiFi MAC address d8:f1:5b:0f:ff:9f
  WiFi Vcc 3.35, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 19344
  WiFi IP address 192.168.1.49
  WiFi signal strength -42dBm, mode none, reconnections 0, sleep mode modem
  Clock register ffffffff
  Socket states: 0 0 0 0 0 0 0 0

m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9K662-MGPSN-6J1FD-3SJ6M-TBYAW
Used output buffers: 3 of 24 (11 max)
=== RTOS ===
Static ram: 23876
Dynamic ram: 75448 of which 12 recycled
Never used RAM 15080, free system stack 184 words
Tasks: NETWORK(ready,12.2%,237) HEAT(delaying,0.0%,314) Move(notifyWait,0.1%,364) MAIN(running,86.4%,441) IDLE(ready,1.4%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:01:10 ago, cause: power up
Last software reset at 2022-02-20 20:14, reason: User, GCodes spinning, available RAM 12048, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 0
MCU temperature: min 22.1, current 27.3, max 27.4
Supply voltage: min 24.0, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2022-02-21 09:36:00
Cache data hit count 2538616899
Slowest loop: 5.80ms; fastest: 0.17ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 4.9ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0 sensor: ok
=== Network ===
Slowest loop: 40.21ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

• WiFi -
  Network state is active
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.23
  WiFi MAC address d8:f1:5b:0f:ff:9f
  WiFi Vcc 3.35, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 19344
  WiFi IP address 192.168.1.49
  WiFi signal strength -42dBm, mode none, reconnections 0, sleep mode modem
  Clock register ffffffff
  Socket states: 0 0 0 0 0 0 0 0

homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Thu Feb 17 2022 16:47:45 GMT+0000 (Greenwich Mean Time)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-355 Y-355 F1800 ; move quickly to X or Y endstop and stop there (first pass)
G1 H1 X-355 ; home X axis
G1 H1 Y-355 ; home Y axis
G1 X5 Y5 F6000 ; go back a few mm
G1 H1 X-355 F360 ; move slowly to X axis endstop once more (second pass)
G1 H1 Y-355 ; then move slowly to Y axis endstop
G90 ; absolute positioning
G1 X15 Y15 F6000 ; go to first bed probe point and home Z
G30 ; home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

; deployprobe.g
; called to deploy a physical Z probe
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Thu Feb 17 2022 16:47:45 GMT+0000 (Greenwich Mean Time)
M280 P5 S10 ; deploy BLTouch

; retractprobe.g
; called to retract a physical Z probe
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Thu Feb 17 2022 16:47:45 GMT+0000 (Greenwich Mean Time)
M280 P5 S90 ; retract BLTouch

Update - I had the wrong Pins in Deploy and retractprobe so now my M401 and M402 is working !

Another update fixed!!! Homed all axis hope this helps somebody else too

@nicaris said in Duet 2 Wifi Problems with BL Touch:

@nicaris
Hi Thanks for responding THese are my config files.
M401 and 402 do not work (m280 does)

m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9K662-MGPSN-6J1FD-3SJ6M-TBYAW
Used output buffers: 3 of 24 (11 max)
=== RTOS ===
Static ram: 23876
Dynamic ram: 75448 of which 12 recycled
Never used RAM 15080, free system stack 184 words
Tasks: NETWORK(ready,12.2%,237) HEAT(delaying,0.0%,314) Move(notifyWait,0.1%,364) MAIN(running,86.4%,441) IDLE(ready,1.4%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:01:10 ago, cause: power up
Last software reset at 2022-02-20 20:14, reason: User, GCodes spinning, available RAM 12048, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 0
MCU temperature: min 22.1, current 27.3, max 27.4
Supply voltage: min 24.0, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2022-02-21 09:36:00
Cache data hit count 2538616899
Slowest loop: 5.80ms; fastest: 0.17ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 4.9ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0 sensor: ok
=== Network ===
Slowest loop: 40.21ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

• WiFi -
  Network state is active
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.23
  WiFi MAC address d8:f1:5b:0f:ff:9f
  WiFi Vcc 3.35, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 19344
  WiFi IP address 192.168.1.49
  WiFi signal strength -42dBm, mode none, reconnections 0, sleep mode modem
  Clock register ffffffff
  Socket states: 0 0 0 0 0 0 0 0

m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9K662-MGPSN-6J1FD-3SJ6M-TBYAW
Used output buffers: 3 of 24 (11 max)
=== RTOS ===
Static ram: 23876
Dynamic ram: 75448 of which 12 recycled
Never used RAM 15080, free system stack 184 words
Tasks: NETWORK(ready,12.2%,237) HEAT(delaying,0.0%,314) Move(notifyWait,0.1%,364) MAIN(running,86.4%,441) IDLE(ready,1.4%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:01:10 ago, cause: power up
Last software reset at 2022-02-20 20:14, reason: User, GCodes spinning, available RAM 12048, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 0
MCU temperature: min 22.1, current 27.3, max 27.4
Supply voltage: min 24.0, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2022-02-21 09:36:00
Cache data hit count 2538616899
Slowest loop: 5.80ms; fastest: 0.17ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 4.9ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0 sensor: ok
=== Network ===
Slowest loop: 40.21ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

• WiFi -
  Network state is active
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.23
  WiFi MAC address d8:f1:5b:0f:ff:9f
  WiFi Vcc 3.35, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 19344
  WiFi IP address 192.168.1.49
  WiFi signal strength -42dBm, mode none, reconnections 0, sleep mode modem
  Clock register ffffffff
  Socket states: 0 0 0 0 0 0 0 0

homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Thu Feb 17 2022 16:47:45 GMT+0000 (Greenwich Mean Time)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-355 Y-355 F1800 ; move quickly to X or Y endstop and stop there (first pass)
G1 H1 X-355 ; home X axis
G1 H1 Y-355 ; home Y axis
G1 X5 Y5 F6000 ; go back a few mm
G1 H1 X-355 F360 ; move slowly to X axis endstop once more (second pass)
G1 H1 Y-355 ; then move slowly to Y axis endstop
G90 ; absolute positioning
G1 X15 Y15 F6000 ; go to first bed probe point and home Z
G30 ; home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

; deployprobe.g
; called to deploy a physical Z probe
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Thu Feb 17 2022 16:47:45 GMT+0000 (Greenwich Mean Time)
M280 P5 S10 ; deploy BLTouch

; retractprobe.g
; called to retract a physical Z probe
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Thu Feb 17 2022 16:47:45 GMT+0000 (Greenwich Mean Time)
M280 P5 S90 ; retract BLTouch

Update - I had the wrong Pins in Deploy and retractprobe so now my M401 and M402 is working !

Oops ! Forgot the following:

M98 P"config.g"

Error: in file macro line 12 column 7: M552: expected string expression
HTTP is enabled on port 80
FTP is disabled
TELNET is enabled on port 23
Error: Heater 3 not found

@nicaris
Hi Thanks for responding THese are my config files.
M401 and 402 do not work (m280 does)

m122

=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9K662-MGPSN-6J1FD-3SJ6M-TBYAW
Used output buffers: 3 of 24 (11 max)
=== RTOS ===
Static ram: 23876
Dynamic ram: 75448 of which 12 recycled
Never used RAM 15080, free system stack 184 words
Tasks: NETWORK(ready,12.2%,237) HEAT(delaying,0.0%,314) Move(notifyWait,0.1%,364) MAIN(running,86.4%,441) IDLE(ready,1.4%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:01:10 ago, cause: power up
Last software reset at 2022-02-20 20:14, reason: User, GCodes spinning, available RAM 12048, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 0
MCU temperature: min 22.1, current 27.3, max 27.4
Supply voltage: min 24.0, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2022-02-21 09:36:00
Cache data hit count 2538616899
Slowest loop: 5.80ms; fastest: 0.17ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 4.9ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0 sensor: ok
=== Network ===
Slowest loop: 40.21ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

• WiFi -
  Network state is active
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.23
  WiFi MAC address d8:f1:5b:0f:ff:9f
  WiFi Vcc 3.35, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 19344
  WiFi IP address 192.168.1.49
  WiFi signal strength -42dBm, mode none, reconnections 0, sleep mode modem
  Clock register ffffffff
  Socket states: 0 0 0 0 0 0 0 0

m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9K662-MGPSN-6J1FD-3SJ6M-TBYAW
Used output buffers: 3 of 24 (11 max)
=== RTOS ===
Static ram: 23876
Dynamic ram: 75448 of which 12 recycled
Never used RAM 15080, free system stack 184 words
Tasks: NETWORK(ready,12.2%,237) HEAT(delaying,0.0%,314) Move(notifyWait,0.1%,364) MAIN(running,86.4%,441) IDLE(ready,1.4%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:01:10 ago, cause: power up
Last software reset at 2022-02-20 20:14, reason: User, GCodes spinning, available RAM 12048, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 0
MCU temperature: min 22.1, current 27.3, max 27.4
Supply voltage: min 24.0, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2022-02-21 09:36:00
Cache data hit count 2538616899
Slowest loop: 5.80ms; fastest: 0.17ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 4.9ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0 sensor: ok
=== Network ===
Slowest loop: 40.21ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

• WiFi -
  Network state is active
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.23
  WiFi MAC address d8:f1:5b:0f:ff:9f
  WiFi Vcc 3.35, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 19344
  WiFi IP address 192.168.1.49
  WiFi signal strength -42dBm, mode none, reconnections 0, sleep mode modem
  Clock register ffffffff
  Socket states: 0 0 0 0 0 0 0 0

homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Thu Feb 17 2022 16:47:45 GMT+0000 (Greenwich Mean Time)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-355 Y-355 F1800 ; move quickly to X or Y endstop and stop there (first pass)
G1 H1 X-355 ; home X axis
G1 H1 Y-355 ; home Y axis
G1 X5 Y5 F6000 ; go back a few mm
G1 H1 X-355 F360 ; move slowly to X axis endstop once more (second pass)
G1 H1 Y-355 ; then move slowly to Y axis endstop
G90 ; absolute positioning
G1 X15 Y15 F6000 ; go to first bed probe point and home Z
G30 ; home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

; deployprobe.g
; called to deploy a physical Z probe
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Thu Feb 17 2022 16:47:45 GMT+0000 (Greenwich Mean Time)
M280 P5 S10 ; deploy BLTouch

; retractprobe.g
; called to retract a physical Z probe
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Thu Feb 17 2022 16:47:45 GMT+0000 (Greenwich Mean Time)
M280 P5 S90 ; retract BLTouch

Hi
I am new to 3D printing but have an ender 5 plus to which I have recently added the Duet 2 Wifi v 1.04.
Wiring has all gone well and everything seems to be in working order ... except for a couple of things :
BL Touch -I can home X and Y no problem But not Z it crashes into the nozzle whatever I do !
The probe deploys and retracts (M280 P0 S10/S90).
As I have not got past this I haven't looked at the other issue which will be the filament runout sensor!
Any Help would be much appreciated
This is my Config.G :
; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; original version generated by RepRapFirmware Configuration Tool v2.1.8 on Fri Apr 10 2020 21:58:05 GMT-0600 (Mountain Daylight Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P" Nick's ender 5 plus" ; set printer name
M552 S1
; Network
M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S1 ; enable Telnet

; Drives
M569 P0 S0 ; physical drive 0 goes forewards
M569 P1 S0 ; physical drive 1 goes forewards
M569 P2 S1 ; physical drive 2 goes forewards
M569 P3 S1
M569 P4 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2:4 E3 ; set drive mapping
; Settings w/o interpolation - commented out
;M350 X32 Y32 Z32 E128 I1 ; configure microstepping with interpolation
;M92 X160.00 Y160.00 Z1600.00 E3533 ; set steps per mm
;M566 X600.00 Y600.00 Z60.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
;M203 X9000.00 Y9000.00 Z1200.00 E6000.00 ; set maximum speeds (mm/min)
;M201 X3000.00 Y3000.00 Z60.00 E250.00 ; set accelerations (mm/s^2)
; Settings w/ interpolation @ 16
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z800.00 E435 ; set steps per mm
M566 X600.00 Y600.00 Z30.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z500.00 E6000.00 ; set maximum speeds (mm/min)
M201 X1500.00 Y1500.00 Z100.00 E1500.00 ; set accelerations (mm/s^2)
M906 X600 Y600 Z600 E600 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y6 Z0 S1 ; set axis minima
M208 X350 Y350 Z400 S0 ; set axis maxima

; Endstops
M574 Z1 S2 ; disabled end stop for z c
M574 X1 S1 P"xstop" ; active low endstop for x-axis
M574 Y1 S1 P"ystop" ; active low endstop for y-axis

; Filament Sensor
M591 D0 P1 S1 C"e0stop"

; Z-Probe
; Based on https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe#Section_Duet_2_WiFi_Ethernet_without_expansion_board
M307 H3 A-1 C-1 D-1
M280 P5 S10 I1 :c
M950 S0 C"exp.heater3" ; Set exp.heater3 (pin8 on expansion socket) as servo pin 0 for BLTouch c
M558 P9 C"^zprobe.in" H5 F120 T6000 A5 R0.1 X0 Y) Z1 ; set Z probe type to bltouch and the dive height + speeds c
G31 P500 X-28 Y-13 Z1.475 ; set Z probe trigger value, offset and trigger height c
M557 X60:300 Y30:300 S20 ; define mesh grid
M574 Z1 S2;c
M280 P5 S90 I1
; Sensors
; See https://duet3d.dozuki.com/Wiki/RepRapFirmware_3_overview#Section_Pin_names_for_Duet_2_WiFi_Ethernet
; for pin names
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; Bed Thermistor
; I replaced my original e0temp thermistor, so if you have stock, use the same values as bed
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; Extruder Thermistor

; Heaters
M950 H0 C"bedheat" T0 ; Create a heater using the bedheat output and the S0 temp sensor (bed heater)
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M143 H0 S120 ; set temperature limit for heater 0 to 120CC0.0000000706
M140 H0 ; Set heater H0 as the bed heater
M950 H1 C"e0heat" T1 ; Create a heater using the e0heat output and the S1 temp sensor (extruder 0)
M143 H1 S290 ; set temperature limit for heater 1 to 290C

; Bed adjustment screw locations
M671 X316:316:46:46 Y295:35:295:35 P0.7 ; mark leveling screws at (316,295) (316,35) (46,295) (46,35)

; Fans
M950 F0 C"fan0" Q500 ; Set fan 0 to pin "fan0" with PWM freq 500 Hz
M106 P0 C"part-cooling" S0.65 H0 ; set fan 0 name and fan speed to 65%. Thermostatic control is turned on
M950 F1 C"fan1" Q500 ; Set fan 1 to pin "fan1" with PWM freq 500 Hz
M106 P1 C"hotend" S0.65 H-1 T100 ; set fan 1 name and fan speed. Thermostatic control is turned off
M950 F2 C"fan2" Q500 ; Set fan 2 to pin "fan2" with PWM freq 500 Hz
M106 P2 S0.85 H-1 ; set fan 2 speed. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501 ; load saved parameters from non-volatile memory
M911 S12 R20 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss