Best posts made by MartinNYHC

Is there already a documentation about the new plugin system? I'm interested to know how to implement a new plugin.

After synchronizing with @Argo what already has been tested and what not I wanted to rule out that the problem is caused by the 1LC toolboard.

Top: E stepper comnnected to a Duet3 3HC
Bottom: E stepper connected to 1LC

So at least we are now sure that it is not related to the 1LC.

My setup:

Same printer as @Argo
Duet3 6HC with 1LC and SBC running RRF 3.4.3
LGX extruder with Rapido HF hotend.

config.g

	; General preferences
M111 S0                     							; Debugging off
G21                         							; Work in millimetres
G90                         							; Send absolute coordinates...
M83                         							; ...but relative extruder moves
M669 K1                     							; Select CoreXY mode
M564 S1 H1                  							; Forbid axis movements when not homed
G4 S1   												; wait for expansion boards to start

; Drives

; --- Z Drive map ---
;     _______
;    | 3 | 4 |
;    | ----- |
;    | 2 | 5 |
;     -------
;      front
;

; Drive directions
M569 P0 S1 												; A (X)
M569 P1 S1 												; B (Y)
M569 P2 S1 												; Z1
M569 P3 S0 												; Z2
M569 P4 S1 												; Z3
M569 P5 S0 												; Z4
M569 P121.0 S1 											; E

; Motor mapping and steps per mm
M584 X1 Y0 Z2:3:4:5 E121.0
M350 X16 Y16 Z16 E16 I1         						; Use 1/16 microstepping with interpolation everywhere
M92 X80 Y80 Z400 E414.92683

; Drive currents
M906 X1500 Y1500 Z1500 E650     						; XYZ and E current
M906 I30                        						; Idle current percentage
M84 S300                        						; Idle timeout

; Accelerations and speed
;M566 X600 Y600 Z60 E8000								; Set maximum instantaneous speed changes (mm/min)
M566 X400 Y400 Z60 E8000								; Set maximum instantaneous speed changes (mm/min)
M203 X30000 Y30000 Z3000 E15000 						; Set maximum speeds (mm/min)
M201 X10000 Y10000 Z250 E1800     						; Set maximum accelerations (mm/s^2) 
M204 P4000 T5000

; Accelerometer
;M955 P121.0 I05										; set address and orientation of tool board

; PA, DAA
;M572 D0 S0.05
M572 D0 S0.035
M593 P"zvdd" F35.2

; Axis travel limits
M208 X5 Y-5 Z0 S1               						; Set axis minima
M208 X350 Y350 Z375 S0          						; Set axis maxima

; Endstops
M574 X2 S1 P"^io1.in"          							; Xmax endstop
M574 Y2 S1 P"^io2.in"          							; Ymax endstop
;M574 Z1 S1 P"^io3.in"                                   ; Z endstop switch
M574 Z1 P"nil" 										; No endstop

; Z probes
;M558 K0 P8 C"121.io0.in" I1 H2.5 F250 T18000 A31 S0.0035 R0.2  ; set Z probe type to switch and the dive height + speeds
;G31 K0 P500 X0 Y25 Z8.74
;M558 K1 P8 C"io3.in" I1 H2 F240 T18000 A31 S0.0035 R0.2 ; set Z probe type to switch and the dive height + speeds
;G31 K1 P500 X0 Y0 Z0			                          ; set Z probe trigger value, offset and trigger height -0.8

; Filament Sensor
;M591 D0 P7 C"121.io2.in" S1

; Bed leveling
M671 X-53:-53:400:400 Y-5:420:420:-5 S20      			; Define Z belts locations (Front_Left, Back_Left, Back_Right, Front_Right)
;M557 X20:335 Y20:330 P5:5
M557 X120:235 Y120:230 P2:2

; Bed heater
M308 S0 P"temp0" Y"thermistor" T100000 B3950             ; configure sensor 0 as thermistor
M950 H0 C"out1" T0                                       ; create bed heater output
M307 H0 B0 S1.00                                         ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                                  ; map heated bed to heater 0
M143 H0 S120                                             ; set temperature limit for heater

; Hotend heater
;M308 S1 P"121.temp1" Y"pt1000"
M308 S1 P"121.temp1" A"Heater 1" Y"thermistor" T100000 B4725 C7.06e-8
M950 H1 C"121.out0" T1
;M950 H1 C"out2" T1
M307 H1 B0 S1       		                             ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S300                                             ; Set temperature limit for heater

; Chamber Thermistor
M308 S2 P"temp1" A"Chamber" Y"thermistor" T100000 B3950  ; configure sensor 2 as thermistor

; MCU sensors
M308 S3 Y"mcu-temp" A"MCU"
M308 S4 Y"drivers" A"Drivers"
M912 P0 S-13					                       	 ; MCU temp calibration

; Fans
;M950 F0 C"121.out1" Q10000                              ; part cooling fan # old Sunon
M950 F0 C"121.out1"			                             ; part cooling fan # new Gsdtime
M106 P0 C"Bed" S0 H-1									 ; part cooling fan
M950 F1 C"121.out2"                                      ; hotend fan
M106 P1 C"Hotend" L0.70 X0.70 H1 T70 S0.70				 ; hotend fan
M950 F2 C"out7" Q10                                      ; air filter fan
M106 P2 C"Filter" S0 H-1 B0.2							 ; air filter fan
M950 F3 C"out4" Q24000                                   ; electronics bay left side
M106 P3 S0.75 H-1 B1 C"Bay"	                             ; electronics bay left side 
;M950 F4 C"1.out3" Q24000                                 ; electronics bay right side
;M106 P4 S0.75 H-1 B1 C"Bay Right"                           ; electronics bay right side
M950 F5 C"out5"	                                    	 ; sbc fan
M106 P5 S0.2 H-1 C"SBC"                         		 ; sbc fan
M950 F6 C"out6"							 			   	 ; chamber light
M106 P6 S1 H-1 C"Light"									 ; chamber light

; Tools
M563 P0 S"Hotend" D0 H1 F0                               ; define tool 0
;G10 P0 X0 Y0 Z-2.75
G10 P0 X0 Y0 Z0
G10 P0 R0 S0                                             ; set initial tool 0 active and standby temperatures to 0C

; Enable debugging via USB
;M111 S1 P0												; Platform
;M111 S1 P1												; Network
;M111 S1 P2												; Webserver
;M111 S1 P3												; GCodes
;M111 S1 P4												; Move
;M111 S1 P5												; Heat
;M111 S1 P6												; DAA
;M111 S1 P7												; Roland
;M111 S1 P8												; Scanner
;M111 S1 P9												; PrintMonitor
;M111 S1 P10											; Storage
;M111 S1 P11											; PortControl
;M111 S1 P12											; DuetExpansion
;M111 S1 P13											; FilamentSensor
;M111 S1 P14 											; Wifi
;M111 S1 P15											; Display
;M111 S1 P16											; LinuxInterface
;M111 S1 P17											; CAN

; Neopixel
M150 X3 Q3000000           ; set LED type to NeoPixel and set SPI frequency to 3MHz
M150 W255 P255 Y255 S3 F0

; Misc
M575 P1 S1 B115200	                					; enable support for PanelDue
M501                                					; load config-override.g
M302 P0													; disallow cold extrudes
T0                                  					; select tool 0

; Auto Z
M98 P"/macros/autoz/edit_me.g" ; load your settings for autoz with klicky probe
M400
M98 P"/macros/autoz/scripts/autoz_globals.g" ; load autoz framework for klicky probe
M400

; ERCF
;M98 P"0:/macros/sys/ercf/lib/init.g"

Gcode file

@Nuramori said in Duet3 Neopixel Wiring:

@MartinNYHC

I have mine working on my BLV with the duet3. It’s actually easier than it was with the duet2. I can share details and pictures in a bit if you’re interested.

Yes please

Here we go....

bossac compiled for MacOS Mojave

@gloomyandy My extruder is clogged Will do the test prints tomorrow.

@Phaedrux Yes, my final way for the future is definitely a tool changer.

At least I got it to run. I'm doing the pre gcode via DWC and then start the main print via Octoprint. I had to block M503 in Octoprint otherwise it stucks in status "starting".

The "slow down during splices" plugin feature seems to work. I printed @100mm and during splices @50mm without any problems.

That's what I was looking for. Very useful. Thx mate!

My fault. I still had an empty SD card inserted into the Duet 3

Sorry for that.

Thanks for pointing out, but I bought a Duet 3 6HC today

Now I need to wait for the ordered frame parts. Did I mention that I hate waiting at all?

To whom it may concern First Beta version.

https://github.com/maziggy/Reprap-Automesh

Got rid of it by disabling DAA for non outer permimeters. Will test this now.

I decided to go with a new PSU. Don't want to start the new build with workarounds

Thanks for your help guys!

Printed the whole day and with the version you provided it works without problems. Thanks again.

@Veti That's what I did

M584 X0.0 Y0.1 Z0.3:0.4:0.5 E0.2                         ; set drive mapping
M671 X-25:-32:398 Y360:10:202 S5			             ; Set up three Z-axis location

Let's see what happens now.

If someone is interested here's the code snippet:

    linesNew = []
    for line in lines:
        if line.startswith('M557'):
            linesNew.append(re.sub(r'^M557 X\d+:\d+ Y\d+:\d+ S\d+:\d+', gridNew, line, flags=re.MULTILINE))
        elif line.startswith('; feature'):
            if "outer perimeter" in line:
                linesNew.append(line + 'M566 X500 Y500\nM201 X6000 Y6000\nM204 P500\nM593 F4.1\n')
            else:
                linesNew.append(line + 'M566 X1000 Y1000\nM201 X2000 Y2000\nM204 P10000\nM593 F0\n')
        else:
            linesNew.append(line)
    return linesNew

Just connected it to the Dotstar connector.

@engikeneer Yes, I already added some additional probing points. Will try it out tomorrow.

Oh yes....and I added a SBC. That's the reason why i changed the board

In the meantime I checked for mechanical issues once again but all seems to be fine.

Why did I touch a running system when I really need to print a lot of stuff. Damn.....

@jay_s_uk NOW i got it I think that's the way for me.

If you say that Sent an email as you suggested.