Posts made by martin7404

So sad.
RIP

I think it will help a lot if you share your config.g and a few photos of your setup. So guys here can pinpoit the issue. Also if you use the search in the forum you will find similar trouble , together with the solutions.\By experience usualy the problem is the speed of comunication between Duet and the external drivers

Fixed it . It was 2 years old SD card. Good quality card. Formated a new one and created new structure witht the current firmware and config. back to printing

After 2 weeks pause I powered my Duet controled printer with Duet 3 board and I am not able to uplad any file
get this kind of error

I think it is SD card
what is the less painfull way to get it up back to life

M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.5.2 (2024-06-11 17:13:58) running on Duet 3 MB6HC v1.01 (standalone mode)
Board ID: 08DJM-9P63L-DJMSS-6JKDA-3S86L-1BDB9
Used output buffers: 3 of 40 (31 max)
=== RTOS ===
Static ram: 155360
Dynamic ram: 120656 of which 488 recycled
Never used RAM 69488, free system stack 202 words
Tasks: NETWORK(1,ready,38.0%,155) ETHERNET(5,nWait 7,0.1%,318) HEAT(3,nWait 6,0.0%,323) Move(4,nWait 6,0.0%,335) CanReceiv(6,nWait 1,0.0%,794) CanSender(5,nWait 7,0.0%,334) CanClock(7,delaying,0.0%,348) TMC(4,nWait 6,9.3%,53) MAIN(1,running,51.9%,103) IDLE(0,ready,0.7%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:28:20 ago, cause: software
Last software reset at 2024-07-29 21:32, reason: User, Gcodes spinning, available RAM 69340, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0044a000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
MCU temperature: min 29.5, current 29.7, max 30.6
Supply voltage: min 24.1, current 24.1, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min n/a, mspos 4, reads 27541, writes 0 timeouts 0
Driver 1: standstill, SG min n/a, mspos 4, reads 27541, writes 0 timeouts 0
Driver 2: standstill, SG min n/a, mspos 8, reads 27541, writes 0 timeouts 0
Driver 3: standstill, SG min n/a, mspos 8, reads 27541, writes 0 timeouts 0
Driver 4: standstill, SG min n/a, mspos 8, reads 27542, writes 0 timeouts 0
Driver 5: standstill, SG min n/a, mspos 8, reads 27542, writes 0 timeouts 0
Date/time: 2024-07-29 22:00:33
Slowest loop: 536.11ms; fastest: 0.07ms
=== Storage ===
Free file entries: 20
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 42.1ms, write time 9.3ms, max retries 0
=== Move ===
DMs created 125, segments created 0, maxWait 0ms, bed compensation in use: none, height map offset 0.000, max steps late 0, min interval 0, bad calcs 0, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters 2 -1 -1 -1, ordering errs 0
=== GCodes ===
Movement locks held by null, null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x0000000
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== Filament sensors ===
check 0 clear 9325857
Extruder 0 sensor: ok
=== CAN ===
Messages queued 2726, received 6055, lost 0, errs 0, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 6, free buffers 50 (min 50), ts 1514/1514/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 557.27ms; fastest: 0.03ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
= Ethernet =
Interface state: active
Error counts: 0 0 0 0 0 0
Socket states: 5 2 2 2 2 0 0 0
=== Multicast handler ===
Responder is inactive, messages received 0, responses 0

M122 P104
Testing SD card write speed...
Error: Failed to write to file, error code 1. Card may be full.
Error: Failed to write to file. Card may be full.
Error: Failed to write to file, error code 1. Card may be full.
Error: Failed to flush data to file. Card may be full.
Error: M122: Failed to write to timing file

@T3P3Tony Was not able to DM will see you there I would get 2 motors if you have them there

@T3P3Tony I am quite interested too. Will be @ formnext in the same hall I suppose

I am sorry to write on old tread but I have a lamer question is this going ot support duet 2 wifi

@Adamfilip It is already
https://duet3d.dozuki.com/Wiki/Stall_detection_and_sensorless_homing
Just set a macro of what will the printer do when stall detection occurs
By experience, it is a tricky business

@dc42 I have a question
Is there a tested closed loop motor with encoder and magnetic brake, tested to work with DUET3 + HCL board

@sebkritikel Happy new year. Thank you very much for the guidelines. For tool heads I think I will go with Hemera, I have one running in a chamber for more than a year and a half. Another option is biqu h2 500, which is designed for heat chambers, this has the great advantage that the heartbreak can be adjusted in height and one great disadvantage of having not hardened drive gears

Sorry for writing in old theme, but I think it could be useful to be found in the same place.
First @sebkritikel very impressive work. I did build in the past a few machines, including IDEX and actively heated ones, but not in the same setup.
I am planning to build a new one and might be using your design as a foundation.
One thing I do not see in CAD and I think is not mentioned anywhere.
How do you align in the Z axis both IDEX heads? In my experience, this is the key for printing in copy and mirror mode

according to this for 1.1 tool board I have to wire only 2 wires for CAN and solder termination pads on the back. Is this correct?

@tecno link text

P.S.
Snapmaker J1 with 1300 EUR fits too

@tecno try MULDEX it is RepRap DIY and fits in your budget

@fbunel I am running such external drives with duet2 and expansion board and it works. For duet 3 I believe they have a board without drivers

I Got one .
It is fast.
Also very close to experince like geting HP laser jet and runing it. Espesialy with PLA.
This thing will take away the good sleep of Prusa, ultimaker, Raise 3d etc

@owend I see . Most probably it is my mistake, so I did some workaround
In the main program I create a loop calling 50 times a macro that contains 3125 loops of my code with echo in the end

In the end both versions with boolean or , and with mod comand did not work. Both program stops on the second itteration of 3125.
I ended up using 50 while loops calling the same code in a macro that rins 3125 loops.
This works like a charm

While iterations = 50
M98 P"test"

And the test macro is

While iterations = 3125
..........

@owend thank you