@dc42 ,
Here is the fresh M122 outout:
RepRapFirmware for Duet 2 WiFi/Ethernet Version 2.03 dated 2019-06-13b2
Executing config.g...HTTP is enabled on port 80
FTP is enabled on port 21
TELNET is enabled on port 23
Warning: the height map was loaded when the current Z=0 datum was not determined probing. This may result in a height offset.
Done!
RepRapFirmw
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03 running on Duet WiFi 1.02 or later
Used output buffers: 1 of 24 (8 max)
=== RTOS ===
Static ram: 25680
Dynamic ram: 93696 of which 0 recycled
Exception stack ram used: 440
Never used ram: 11256
Tasks: NETWORK(ready,524) HEAT(blocked,1236) MAIN(running,3756) IDLE(ready,160)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:06:39 ago, cause: software
Last software reset at 2019-08-11 14:36, reason: User, spinning module GCodes, available RAM 11376 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 7
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 7.7ms, max retries 0
MCU temperature: min 26.9, current 28.5, max 28.8
Supply voltage: min 23.2, current 23.9, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max 0/100
Driver 1: ok, SG min/max 0/48
Driver 2: ok, SG min/max 0/1023
Driver 3: standstill, SG min/max not available
Driver 4: ok, SG min/max 0/3
Date/time: 2019-08-11 14:43:31
Cache data hit count 1587842547
Slowest loop: 105.25ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 166, MinFreeDm: 163, MaxWait: 297857ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 8, completed moves: 7, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.6
Heater 1 is on, I-accum = 0.5
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 2 in use
Movement lock held by file
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 43 8 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 200.97ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8
- WiFi -
Network state is running
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 75
Failed to get WiFi status
Socket states: 0 0 0 0 0 0 0 0
ok
Thanks,
Madhu.