Good afternoon,
I have a core XY (Voron 2.1) with a bed of 350x350 mm, and when I print before, I make a G29, but it seems that it does not carry the mesh well, because the nozzle does not stick well throughout the bed. Photo command I am using an original BlTouch.
The first thing I do is a Macro to start printing.
I send the files, let's see if there is something wrong.
The M566 (Which has nothing to do with the error, is it correct, for a good operation or E, should it be faster?)
Thank you very much in advance.
CONFIG.G
; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Sun Mar 10 2019 17:30:42 GMT+0100 (hora estándar de Europa central)
; General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M667 S1 ; Select CoreXY mode
M555 P2 ; Set firmware compatibility to look like Marlin
; Network
M550 P"Margarita" ; Set machine name
M552 S1 ; Enable network
M587 S"i" P"mi***" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet
; Drives
M584 X0 Y1 Z5:6:7:8 E3:4:2 ; motor bindings
M671 X400:400:-50:-50 Y355:-85:-85:355 S5 ; Z drive positions
M569 P0 S1 ; X motor direction
M569 P1 S1 ; Y motor direction
M569 P5 S0 ; Z-- motor direction
M569 P6 S1 ; Z-+ motor direction
M569 P7 S0 ; Z++ motor direction
M569 P8 S1 ; Z+- motor direction
M569 P3 S1 ; E0 motor direction
;M569 P4 S1 ; E1 motor direction
;M569 P2 S1 ; E2 motor direction
M350 X256 Y256 Z256 I0 ; Configure microstepping without interpolation
M350 E16 I0 ; Configure microstepping with interpolation
M92 X1280.00 Y1280.00 Z6400.00 E549.00 ; Set steps per mm
M566 X900.00 Y900.00 Z150.00 E120.00 ; Set maximum instantaneous speed changes (mm/min)
M203 X24000.00 Y24000.00 Z1800.00 E6000.00 ; Set maximum speeds (mm/min)
M201 X3600.00 Y3600.00 Z500.00 E3600.00 ; Set accelerations (mm/s^2)
M906 X900.00 Y900.00 Z900.00 E900.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X350 Y350 Z350 S0 ; Set axis maxima
; Endstops
;M574 X1 Y1 Z1 S0 ; Set active low and disabled endstops
M574 X1 Y1 S0
;M574 Z1 S0 ; Set active low and disabled endstops
M98 P"/macros/Zprobe BlTouch"
; Heaters
M305 P0 T100000 B3950 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S150 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4725 C7.060000e-8 R4700
M143 H1 S280 ; Set temperature limit for heater 1 to 280C
; Fans
M106 P2 C"CAPA" ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 T45 H1 C"HOTEND" ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
; Tools
M563 P0 D0 H1 F2 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
; Automatic power saving
M911 S22 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss
;Registro de eventos
M929 P"registro.txt" S1 ; iniciar el registro en el archivo eventlog.txt
; Calibracion de la Temperatura
M912 P0 S-10
M572 D0 S0.15
; Automatic saving after power loss is not enabled
M501
; Custom settings are not configured
MACRO BLTOUCH:
; Z-Probe con BLTouch
M98 P"/macros/Activar EndStop"
M574 Z1 S2 ; Set endstops controlled by probe
M307 H7 A-1 C-1 D-1 ; Disable heater on PWM channel for BLTouch
M558 P9 F400 H5 R0.2 T6000 A5 S0.03 ;B1 ; Set Z probe type to bltouch and the dive height + speeds
G31 P25 X0 Y-26.30 Z1.40 ; Set Z probe trigger value, offset and trigger height
M557 X50:300 Y50:300 S20 ; Define mesh grid
MACRO INICIAR IMPRESION:
;M98 P"/macros/Iniciar Impresion" ; Cargar Parametros de la malla
M561
G29 S2
M280 P7 S160; Liberación de alarma BLTouch
G4 P100; retraso para BLTouch
M98 P"/sys/homeall.g"
G1 X175 Y175 F12000
G30
G32
G1 X175 Y175 F12000
G30
G1 Z10 F36000
G29
Thank you.
