Posts made by jer1001

@jay_s_uk I am away at the minute, but will have a look and report back. Many thanks

@jay_s_uk Hi I use events for some of the errors, to filter out other issues. I don't see where the actual measured variable is recorded or how it is named.
something like if measure value is < 0 then..... Many thanks

I have had a couple of circumstances when I have had a negative reading from the filament sensor. I would like to ignore these errors and prevent negative readings causing a pause. Does anyone know the best way to achieve this? Many thanks Jeremy

@gloomyandy I owe you for that one, many thanks indeed. It is homing on this, will revert at end of homing to spreadcycle. Thanks again

; homex.g
; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v3.5.0-rc.2+3 on Mon Jan 15 2024 12:53:37 GMT+0000 (Greenwich Mean Time)
M569 P0 D3 V0
M915 H200 X Y S3 R0 F0        ; set sensorless homing

; lift Z
G91 ; relative positioning
G1 H2 Z5 ; move Z relative to current position to avoid dragging nozzle over the bed
G90 ; absolute positioning

; home X

G1 H1 X-300 F3000 ; coarse home in the -X direction
G1 H2 X20 F1500 ; move back 5mm
;G1 H1 X{-var.maxTravel} F300 ; fine home in the -X direction
;G1 H2 Z-5 F6000 ; lower Z again

Anyone know why stallguard doesn't initiate with duet 3 mini. Changing the sensitivity doesn't work, it is just not responsive. It clatters no matter what. I can get it working on a Duet 2 board without any hiccup at all with a super light touch as well. It doesnt appear to be firmware related as I rolled back to 4.6..

I am not able to get sensorless homing working with a duet 3 mini running firmware 3.5 rc2. I have looked and cannot see where it is going wrong and have tried numerous settings to no avail. Not sure if I should go back to an older version of the firmware. Hopefully I am missing something really stupid. My main config is below followed by my homex file. Many thanks

; Configuration file for RepRapFirmware on Duet 3 Mini 5+ Ethernet
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.5.0-rc.2+3 on Mon Jan 15 2024 12:53:36 GMT+0000 (Greenwich Mean Time)

; General
M550 P"MK3" ; set hostname

; Network
M552 S1                                 ; configure Ethernet adapter

M552 P0.0.0.0 S1                        ; enable network and acquire dynamic address via DHCP
M586 P0 S1                              ; enable HTTP
M586 P1 S0                              ; disable FTP
M586 P2 S0                              ; disable Telnet


; Smart Drivers
M569 P0.0 S1 D2 ; driver 0.0 goes forwards (X axis)
M569 P0.1 S0 D2 ; driver 0.1 goes forwards (Y axis)
M569 P0.2 S1 D2 ; driver 0.2 goes forwards (Z axis)
M569 P0.3 S1 D2 ; driver 0.3 goes forwards (extruder 0)
M569 P0.4 S1 D2 ; driver 0.4 goes forwards (Z axis)

; Motor Idle Current Reduction
M906 I30 ; set motor current idle factor
M84 S30 ; set motor current idle timeout

; Axes
M584 X0.0 Y0.1 Z0.2:0.4 ; set axis mapping
M350 X16 Y16 Z16 I1 ; configure microstepping with interpolation
M906 X800 Y800 Z800 ; set axis driver currents
M92 X100 Y100 Z400  ; configure steps per mm
M208 X0:250 Y0:210 Z0:210 ; set minimum and maximum axis limits
M566 X900 Y900 Z12 ; set maximum instantaneous speed changes (mm/min)
M203 X10000 Y10000 Z180 ; set maximum speeds (mm/min)
M201 X500 Y500 Z20 ; set accelerations (mm/s^2)

; Extruders
M584 E0.3 ; set extruder mapping
M350 E16 I1 ; configure microstepping with interpolation
M906 E400 ; set extruder driver currents
M92 E140 ; configure steps per mm
M566 E120 ; set maximum instantaneous speed changes (mm/min)
M203 E3600 ; set maximum speeds (mm/min)
M201 E250 ; set accelerations (mm/s^2)

; Kinematics
M669 K0 ; configure Cartesian kinematics





; Endstops
M574 X1 S3 ; configure X axis endstop
M574 Y1 S3 ; configure Y axis endstop
M574 Z1 S2 ; configure Z axis endstop

; Probes
M558 K0 P5 C"io2.in" H5 F120 T6000 ; configure digital probe via slot #0
M308 S2 P"temp2" A"Pinda V2" Y"thermistor" T100000 B3950                       ; added from CNC kitch
G31 P500 X0 Y0 Z1 ; set Z probe trigger value, offset and trigger height


;Stall detection
;M915 X Y R0 F0
M915 X Y S1 F0 H200 R4700 ; xand y axes

; Mesh Bed Compensation
M557 X25:225 Y25:185 S50:50 ; define grid for mesh bed compensation

; Sensors
M308 S0 P"temp0" Y"thermistor" A"Heated Bed" T100000 B4725 C7.06e-8 ; configure sensor #0
M308 S1 P"temp1" Y"thermistor" A"Nozzle" T100000 B4725 C7.06e-8 ; configure sensor #1

; Heaters
M950 H0 C"out0" T0 ; create heater #0
M143 H0 P0 T0 C0 S120 A0 ; configure heater monitor #0 for heater #0
M307 H0 R2.43 D5.5 E1.35 K0.56 B0 ; configure model of heater #0
M950 H1 C"out1" T1 ; create heater #1
M143 H1 P0 T1 C0 S285 A0 ; configure heater monitor #0 for heater #1
M307 H1 R2.43 D5.5 E1.35 K0.56 B0 ; configure model of heater #1

; Heated beds
M140 P0 H0 ; configure heated bed #0

; Fans
M950 F0 C"out3" ; create fan #0
M106 P0 S0 L0 X1 B0.1 ; configure fan #0
M950 F1 C"out4" ; create fan #1
M106 P1 S0 B0.1 H1 T45 ; configure fan #1

; Tools
M563 P0 D0 H1 F0 ; create tool #0
M568 P0 R0 S0 ; set initial tool #0 active and standby temperatures to 0C

; Miscellaneous
T0 ; select first tool

; homex.g
; called to home the x axis

G91 							; use relative positioning
M400

M913 X30					    ; drop motor currents to 25%
M201 X1000 Y1000
G1 H2 X0.5 Y-0.5 F10000			; energise motors to ensure they are not stall
M400                            ; make sure everything has stopped before we change the motor currents


M569 P0 V0                      ; force to stealth chop

M915 H200 X Y S1 R0 F0 		    ; set X and Y to sensitivity 3, do nothing when stall, unfiltered

G1 H2 Z3 F5000					; lift Z 3mm
G1 H1 X-300 F4200				; move left 400mm, stopping at the endstop
G1 H1 X100 F2000 				; move away from end
G1 H2 Z-3 F1200					; lower Z
G90 							; back to absolute positioning

M400 							; make sure everything has stopped before we reset the motor currents
M913 X100 Y100 					; motor currents back to 100%

@jer1001 Sorry I should have said V3

Hi I would like to know what is the distance between the magnet and the sensor on the V4 filament sensor should be. The housing designed by Lo-fi gives an error of magnet too strong. The standard housing is working fine but there is a little more filament resistance. If I know the optimum distance I may modify the Lo-fi housing to deal with the change in magnet of the new version (V4) Anyway if someone knows the dimension it would make things very simple. Many thanks Jeremy

Hi Andre
Thanks for your help, makes sense.
Jeremy

I am trying to understand if there are any settings to get the duet to switch off the 24V power supply using the M81 command. As far as I can see the heaters are turned off if it detects an issue, but it does not turn off the power supply. I can switch the power on and off no issues and this is handy at the end of printing. However I am not sure about how error messages can be arranged to power down the 24 volt power supply.

Many thanks

Jeremy

This works perfectly. I can turn the 24 volt power supply on and off and still see what is going on. I would like the machine to turn the 24 volt power supply off on errors eg over temperature on the bed or extruder, no sensor, temperature not rising sufficiently etc. I added M81 to the stop macro and this hasn't worked for error messages. I guess this macro doesn't run on error commands. If someone can tell me how to assign error outputs to run a shut down of the 24 volts power supply I would appreciate. Many thanks Jeremy

Jeremy

PERFECT
MANY THANKS

Jeremy

Duet 2, I want to arrange for the 24 volt power supply to be switched off via a solid state relay in the event of error reports.. and when required at the end of print jobs. I have a secondary 5 volt supply for the duet so if remains on when the 24 volt power supply is switched off. I would like to configure so that the 24 volt power supply is switched on via 5 volts applied to a SSR. I am not clear if or how I can use the PS_ON pin to arrange for this to happen as it goes to ground and I need to arrange 5 volts to get to the SSR via a switch from the duet. I hope this make sense.

Many thanks Jeremy